OCMJ中文模块液晶图文显示器使用说明.doc

OCMJ中文液晶显示模块说明书 35 OCMJ中文模块系列液晶图文显示器 使用说明书- 感谢您购买和使用我们的 OCMJ(奥可拉中文集成模块)系列液晶显示器产品， 我们非常重视您的意见和建议，欢迎拨打热线电获取技术咨询与服务，或浏览http:/WWW.GPT.COM.CN 了解最新的产品与应用信息。产品简介： OCMJ中文模块系列液晶显示器内含 GB 2312 16*16点阵国标一级简体汉字和 ASCII8*8点阵英文字库，用户输入区位码或 ASCII 码即可实现文本显示。 OCMJ中文模块系列液晶显示器同时为用户提供位点阵和字节点阵两种图形显示功能，用户可在指定的屏幕位置上以位为单位或以字节为单位进行图形显示。 位点阵图形方式适用于显示例如股票走势曲线/电流电压波形等；字节点阵图形方式除用于造字外，实际上可用于编制和显示任何可以以图形方式表达的内容。 用户可以清除或上/下/左/右移动当前显示屏幕。 所有的用户接口命令都是高级语言格式，规划整齐的9个用户接口命令代码非常容易记忆。OCMJ 系列液晶显示器致力于减轻编程负担。 用户硬件接口采用 ASK/ANSWER 握手协议,采用 8 位并行数据格式。独立于 CPU 硬件的 ASK/ANSWER 握手协议简单可靠。 让繁杂的寄存器资料和手册成为过去 - 从 OCMJ中文模块开始。用户命令: 用户通过用户命令调用 OCMJ 系列液晶显示器的各种功能。用户命令分为 3 类9 条。分别是： 一) 字符显示命令：1)显示国标汉字 2)显示ASCII字符 二) 图形显示命令： 3)显示位点阵 4)显示字节点阵三) 屏幕控制命令： 5)清屏 6)上移 7)下移 8)左移 9)右移命令格式一) 字符显示命令:1) 显示国标汉字: 操作码 操作数 F0 XX YY QQ WW 注:5 字节命令XX YY：以 16*16 点阵为单位的屏幕坐标值QQ WW：GB 2312 汉字区位码2) 显示ASCII字符: 操作码 操作数 F1 XX YY AS 注:4 字节命令XX YY：以 8*8 点阵为单位的屏幕坐标值 AS：ASCII 字符代码 二) 图形显示命令:3) 显示位点阵:操作码 操作数 F2 XX YY 注:3 字节命令XX YY：以 1*1 点阵为单位的屏幕坐标值4) 显示字节点阵：操作码 操作数 F3 XX YY BT 注：4 字节命令XX YY：以 1*8 点阵为单位的屏幕坐标值 BT：字节像素值，0 显示白点，1 显示黑点三) 屏幕控制命令：5) 清屏:操作码 F4 注：单字节命令 6) 上移：操作码 F5 注：单字节命令7) 下移：操作码 F6 注：单字节命令8) 左移：操作码 F7 注：单字节命令9) 右移：操作码 F8 注：单字节命令硬件接口: 接口协议为 ASK/ANSWER 握手方式。ASK=1 表示 OCMJ 忙于内部处理，不能接收用户命令；ASK=0 表示 OCMJ 空闲，等待接收用户命令。发送用户命令到 OCMJ可在 ASK=0 后的任意时刻开始，先把用户命令的当前字节放到数据线上，接着发高电平ANSWER 脉冲把当前用户命令字节锁存到 OCMJ 中。然后判断OCMJ模块是否在忙于内部处理数据，（ASK=1？）如果ASK=1，那么把ANSWER拉低，等待下一次（ASK=0）再送下一个数据。引脚排列及引脚说明： AVR单片机ATmega103/128与OCMJ4X8接线: D0D7 接PORTA.0PORTA.7; ASK接PORTE.6; ANSWER接PORTE.7; RESET接PORTC.3 附源程序:megaled.c中文模块外部接口连接: 以上接法为AT89C52/AT90S8515/ATmega103/128与OCMJ4X8模块连接，仅供参考注：模块电源VDD与LED背光电源最好取两组电源分开供，以免背光源功耗相对大一点而影响模块显示。另外，LCD+/LCD-为背光源引脚，PCB板连线途经两焊盘（断开），由用户接上相应的电阻调整LED背光亮度，电阻阻值在10欧-30欧之间。RT1/RT2接脚为辉度调节电位器接脚，接20K左右电位器可调节辉度。AT89C52单片机RESET为低电平有效。AVR AT90S8515/ATmega103/128单片机RESET为高电平有效。OCMJ4X8每个中文字符占用16X16点阵,1行8个汉字,即8X16=128点阵OCMJ4X8每个中文字符占用16X16点阵,4行4个汉字,即4X16=64点阵所以OCMJ液晶显示器也是64X128点阵,可由用户组成你所需大小的汉字、符号、图形,参考实验例子可上双龙网站老耿专栏下载!以上列表为汉字、ASC码显示屏幕坐标（ASC码Y坐标一点阵坐标为准）如显示图形点阵，则以128*64（OCMJ4X8）或128*32（OCMJ2X8）点阵坐标为准，可在屏幕任意位置显示。软件编程：(MCS-51单片机为例)1、握手协议：（子程序）SUB1：MOV P1,A;送数NOPSETB ANSWER;置1NOP HE3:JNB ASK,HE3;ASK=0等,送数CLR ANSWER;ASK=1,则使ANSWER=0 HE4:JB ASK,HE4;ASK=1等,ASK=0顺执RET ;返回2、初始化：ORG 000H;程序首址 LJMP 100H;跳过中断区 ORG 100H; MOV SP,#60H;设堆栈 CLR ANSWER;ANSWER=0 SETB ASK;ASK=13、显示一个汉字“啊” ：MOV A,#0F0H;送汉字命令HE:JB ASK,HE;ASK=1,忙,等,ASK=0顺执ACALL SUB1;调用握手协议送数MOV A,#02H;02H,XX,16*16点阵为单位的屏幕座标ACALL SUB1;调用 MOV A,#00H;00H,YY,16*16点阵为单位的屏幕座标 ACALL SUB1MOV A,#10H;10H,QQ, GB2312汉字区位码高位ACALL SUB1 MOV A,#01H;01H,WW, GB2312汉字区位码低位 ACALL SUB14、显示一个ASC码 “A” ： MOV A,#0F1H;显示ASCII字符HE:JB ASK,HE;ASK=1,忙,等,ASK=0 顺执ACALL SUB1;调用MOV A,#04H;04H,XX,8*8点阵为单位的屏幕座标值XACALL SUB1 MOV A,#00H;00H,YY, 8*8点阵为单位的屏幕座标值Y ACALL SUB1MOV A,#41H;AS-ASCII字符代码AACALL SUB1 5、显示一点（1*1点阵）：MOV A,#0F2H;显示位点阵HE:JB ASK,HE;ASK=1,忙,等,ASK=0 顺执ACALL SUB1;调用MOV A,#20H;20H,XX,以1*1点阵为单位的屏幕座标值XACALL SUB1 MOV A,#00H;00H,YY,以1*1点阵为单位的屏幕座标值Y ACALL SUB16、显示一字节（1*8点阵，横向）：MOV A,#0F3H; 显示字节点阵HE:JB ASK,HE; ASK=1,忙,等,ASK=0 顺执ACALL SUB1;调用MOV A,#20H;20H,XX,以1*8点阵为单位的屏幕座标值XACALL SUB1 MOV A,#00H;00H,YY,以1*8点阵为单位的屏幕座标值Y ACALL SUB17、控制指令（以清屏为例）：MOV A,#0F4H;清屏HE:JB ASK,HE; ASK=1,忙,等,ASK=0 顺执ACALL SUB1;调用以上程序坐标值为OCMJ4X8模块坐标;OCMJ2X8模块坐标请参考OCMJ2X8坐标表;ASCLL码表符 号十进制十六进制符 号十进制十六进制符 号十进制十六进制3220H6440Ha9761H!3321HA6541Hb9862H3422HB6642Hc9963H#3523HC6743Hd10064H$3624HD6844He10165H%3725HE6945Hf10266H&3826HF7046Hg10367H3927HG7147Hh10468H)4028HH7248Hi10569H(4129HI7349Hj1066AH422AHJ744AHk1076BH432BHK754BHl1086CH，442CHL764CHm1096DH452DHM774DHn1106EH462EHN784EHo1116FH472FHO794FHp11270H04830HP8050Hq11371H14931HQ8151Hr11472H25032HR8252Hs11573H35133HS8353Ht11674H45234HT8454Hu11775H55335HU8555Hv11876H65436HV8656Hw11977H75537HW8757Hx12078H85638HX8858Hy12179H95739HY8959Hz1227AH:583AHZ905AH1237BH;593BH915BH1247CH623EH945EH?633FH955FH 新增加符号： 7FH 80H 81H 82H 83H 84H 85H 86H 87H 127 128 129 130 131 132 133 134 135以上符号可用(F1)指令输入注: 局部清屏指令 F0 XX YY 55D 90D 此指令可清屏16X16点阵区域单片机与OCMJ4X8模块的实验源程序可上双龙网站下载http:WWW.SL.COM.CN以下程序均在广州天河双龙电子有限公司的SL-AVR及SL-MEGA103开发实验器上验证通过! ;/* ; OCMJ4X8汉字液晶显示器测试程序 * ; PB0-PB7: lcd的数据线 * ; PD0 : lcd的ASK * ; PD1 : lcd的ANSWER * ; PD2 : lcd的RESET * ; 本实验用8515在SL-AVR通过 * ; 广州双龙电子有限公司 吴春生编程实验于01/8/28 *;*/.included:0000rjmpreset.deftemp=r16.defsenddr=r17.defdt=r18.defxx=r19 ;坐标X.defyy=r20 ;坐标Y.def qq=r21;汉字高字节 区位码.defww=r22 ;汉字低字节.defasc=r23;ASCII码.defbt=r24;字节象素值 0:白点 1:黑点.equask=0.equanswer=1.equlcdreset=2.org0x0010reset:lditemp,high(ramend) ;设置堆栈outsph,templditemp,low(ramend)outspl,templdidt,42rcallinit ;初始化 rcallclr ;清屏 ldixx,0x02ldiyy,0x03ldiqq,0x37ldiww,0x33rcalldishzaa:rcalldelayrcallrightrcallrightrjmpaa dishz: ;显示16*16汉字ldisenddr,0xf0rcallsendmovsenddr,xx ;xx:X坐标(0x02-0x09)rcallsendmovsenddr,yy ;yy:Y坐标(0x00-0x03)rcallsendmovsenddr,qq rcallsendmovsenddr,wwrcallsendretdisasc: ;显示8*8ASCII码ldisenddr,0xf1rcallsendmovsenddr,xx ;xx:X坐标(0x04-0x13)rcallsend movsenddr,yy ;yy:Y坐标(0x00-0x39)rcallsendmovsenddr,ascrcallsendretdisbit: ;以1*1显示位点阵ldisenddr,0xf2rcallsendmovsenddr,xx ;xx:X坐标(0x20-0x9f)rcallsendmovsenddr,yy ;yy:Y坐标(0x00-0x3f)rcallsendretdisdb: ;以1*8点阵为单位的坐标值ldisenddr,0xf3rcallsendmovsenddr,xx ;xx:X坐标(0x04-0x13)rcallsendmovsenddr,yy ;yy:Y坐标(0x00-0x3f)rcallsendmovsenddr,btrcallsendretclr16: ;局部清屏，清16*16点阵区域ldisenddr,0xf0rcallsendmovsenddr,xx ;xx:X坐标(0x02-0x09)rcallsendmovsenddr,yy ;yy:Y坐标(0x00-0x03)rcallsendldisenddr,55rcallsendldisenddr,90rcallsendretclr: ;清屏ldisenddr,0xf4rcallsendretup: ;上移ldisenddr,0xf5rcallsendretdown: ;下移ldisenddr,0xf6rcallsendretleft: ;左移ldisenddr,0xf7rcallsendretright: ;右移ldisenddr,0xf8rcallsendretinit: ;初始化lditemp,0xff ;B口为数据线，输出outddrb,templditemp,0xf8|(1lcdreset)|(1answer)|(0ask)outddrd,temp ;D口为控制线lditemp,0xf8|(1lcdreset)|(0answer)|(0ask) outportd,temp ;ASK三态输入，ANSWER=0，LCDRESET=1retsend:sbicpind,ask ;检查ASK=0? (0:空闲 1:忙)rjmpsend ;ASK=1 等待outportb, senddr ;ASK=0 执行nopsbi portd,answer ;ANSWER置高,把用户命令锁存到OCMJnopsend1:sbispind,ask ;检查ASK=1?rjmpsend1 ;ASK=0 等待 cbiportd,answer ;ASK=1 ANSWER置1retdelay: push dt del0: push dtdel1: push dt del2: push dtdel3: dec dt brne del3 pop dt dec dt brne del2 pop dt dec dt brne del1 pop dt dec dt brne del0 pop dt ret用AVR单片机AT90S8515与OCMJ4X8模块做演示实验源程序LCD.C/* 双龙电子公司-中文LCD演示程序(ICCAVR) 作者：詹卫前 1、应包含头文件slavr.h 2、在工程选项中的Additional Lib中填入slavr 使编译器使用附加库文件libslavr.a 3、数据线D0D7接PORTA ASK=PORTD.2 ANSWER=PORTD.3 RESET=PORTC.3 */#include #include /* 定义OCMJ4X8端口 */DATA_PORT=PORTA#define data_port PORTA/ASK=PORTD.2#define ask (PIND&0x04)/ANSWER=PORTD.3#define set_answer asm(sbi 0x12,3)#define clr_answer asm(cbi 0x12,3)/RESTE=PORTC.3#define set_reset asm(sbi 0x15,3)#define clr_reset asm(cbi 0x15,3) #define wait asm(nopn nop)/*- 双龙公司图标数据 -*/*- 宽度x高度=32x32 -*/const unsigned char sl_ico128=0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFE,0x7F,0xFF,0xFF,0xF8,0x3F,0xFF,0xFF,0xE0,0x1F,0xFF,0xFF,0x80,0x1F,0xFF,0xFF,0x00,0x3F,0xFF,0xFE,0x01,0xFF,0xFF,0xFC,0x07,0xFF,0xFF,0xF0,0x1F,0xFF,0xFF,0xF0,0x3F,0xFF,0xFF,0xF0,0x3F,0xFF,0xFF,0xF0,0x7F,0xFF,0xFF,0xE0,0x7F,0xFF,0xFF,0xF0,0x3F,0xFF,0xFF,0xF0,0x1F,0xFF,0xFF,0xF8,0x0F,0xFF,0xFF,0xFC,0x0F,0xFF,0xFF,0xFC,0x07,0xFF,0xFF,0xFE,0x03,0xFF,0xFF,0xFF,0x03,0xFF,0xFF,0xFF,0x03,0xFF,0xFF,0xFF,0x01,0xFF,0xFF,0xFF,0x81,0xFF,0xFF,0xFF,0x01,0xFF,0xFF,0xFF,0x03,0xFF,0xFF,0xFE,0x03,0xFF,0xFF,0xF8,0x03,0xFF,0xFF,0xE0,0x07,0xFF,0xFE,0x00,0x2F,0xFF,0xFF,0xC0,0x3F,0xFF,0xFF,0xFD,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF;/*- ATMEL位图文件数据 -*/*- 宽度x高度=104x49 -*/const unsigned char atmel_bmp637=0x00,0x00,0x0F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF8,0x00,0x00,0x0F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF8,0x00,0x00,0x1F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF8,0x00,0x00,0x1F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF8,0x00,0x00,0x3F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF8,0x00,0x00,0x7F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF8,0x00,0x00,0x7F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF8,0x00,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF8,0x00,0x00,0x00,0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xFC,0x7F,0x9F,0xFF,0xFF,0xF8,0x3F,0xFF,0xE7,0xF8,0x00,0x00,0x03,0xFC,0x7F,0x9F,0xFF,0xFF,0xFC,0x3F,0xFF,0xE7,0xF8,0x00,0x00,0x07,0xFC,0x7F,0x9F,0xFF,0xFF,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x00,0x07,0xFC,0x7F,0x9F,0xC7,0xF9,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x00,0x0F,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x00,0x0F,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x00,0x1F,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x00,0x1F,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x00,0x3F,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0x00,0x07,0xF8,0x00,0x00,0x3F,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0x00,0x07,0xF8,0x00,0x00,0x7F,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x00,0x7F,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x00,0xFF,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x00,0xFF,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x01,0xFF,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x01,0xFF,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x03,0xFF,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x03,0xFF,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x07,0xFB,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0x00,0x07,0xF8,0x00,0x07,0xF3,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0x00,0x07,0xF8,0x00,0x0F,0xF3,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xF8,0x00,0x1F,0xE3,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xFF,0xF8,0x1F,0xE3,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xFF,0xF0,0x3F,0xC3,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xFF,0xF0,0x3F,0xC3,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xFF,0xE0,0x7F,0xF3,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xFF,0xE0,0x7F,0xF3,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xFF,0xC0,0xFF,0xF3,0xFC,0x7F,0x9F,0xC7,0xF8,0xFE,0x3F,0xFF,0xE7,0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFE,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFE,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFC,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFC,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF8,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00;/*- 文字: 和 -*/*- 楷体_GB231248; 此字体下对应的点阵为：宽x高=64x64 -*/const unsigned char hz1480=0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xFC,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0xE0,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xFF,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x87,0xC0,0x00,0x00,0x00,0x00,0x00,0x18,0x07,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x87,0xC0,0x00,0x00,0x00,0x00,0x00,0x03,0xFF,0xE0,0x00,0x06,0x00,0x00,0x00,0x0F,0xFF,0xC0,0x00,0x1F,0x80,0x00,0x00,0xFF,0xF8,0x00,0x01,0xFF,0xE0,0x00,0x0F,0xFF,0x80,0x7F,0xFF,0xFF,0xF0,0x07,0xFF,0xE7,0x80,0x7F,0xFF,0xFF,0xF0,0x1F,0xFE,0x0F,0x80,0x7F,0x80,0x07,0xE0,0x0F,0xF0,0x1F,0x80,0x3E,0x00,0x07,0xC0,0x07,0x80,0x3F,0x80,0x1E,0x00,0x07,0xC0,0x00,0x00,0x3F,0x80,0x1E,0x00,0x07,0x80,0x00,0x00,0x7F,0x80,0x1E,0x00,0x07,0x80,0x00,0x00,0xFB,0x80,0x0E,0x00,0x07,0x80,0x00,0x00,0xF3,0xF8,0x0E,0x00,0x0F,0x00,0x00,0x01,0xE3,0xFE,0x0E,0x00,0x0F,0x00,0x00,0x03,0xE3,0xBF,0x0E,0x00,0x0F,0x00,0x00,0x07,0xC3,0x9F,0x07,0x00,0x0E,0x00,0x00,0x07,0x83,0x8F,0x07,0x00,0x0E,0x00,0x00,0x0F,0x03,0x83,0x07,0x00,0x1F,0x00,0x00,0x1E,0x03,0x80,0x07,0x1F,0xFF,0x80,0x00,0x3C,0x03,0x80,0x07,0xFF,0xFF,0x80,0x00,0x78,0x03,0x80,0x07,0xFF,0x00,0x00,0x00,0x70,0x03,0x80,0x03,0x00,0x00,0x00,0x00,0xE0,0x03,0x80,0x03,0x00,0x00,0x00,0x01,0xC0,0x03,0x80,0x03,0x00,0x00,0x00,0x03,0x80,0x07,0x80,0x03,0x00,0x00,0x00,0x06,0x00,0x07,0x80,0x01,0x00,0x00,0x00,0x0C,0x00,0x07,0x80,0x00,0x00,0x00,0x00,0x10,0x00,0x07,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00;const unsigned char hz2132=/*- 文字: 欢 -*/*- 楷体_GB231224; 此字体下对应的点阵为：宽x高=32x33 -*/0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x70,0x00,0x00,0x00,0x70,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0xC0,0x00,0x00,0x00,0xC0,0x00,0x00,0x60,0x81,0x00,0x03,0xF1,0x8F,0xC0,0x3E,0x71,0xF9,0xE0,0x10,0x63,0x01,0x80,0x00,0x62,0x03,0x00,0x08,0x64,0xC2,0x00,0x04,0x60,0x60,0x00,0x06,0xC0,0x60,0x00,0x03,0xC0,0x60,0x00,0x01,0xC0,0x60,0x00,0x01,0xC0,0xD0,0x00,0x01,0x60,0xD8,0x00,0x03,0x70,0xCC,0x00,0x06,0x31,0x8C,0x00,0x04,0x11,0x86,0x00,0x08,0x03,0x03,0x80,0x10,0x06,0x03,0xC0,0x20,0x0C,0x01,0xF0,0x00,0x18,0x00,0xFC,0x00,0x20,0x00,0x70,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00;const unsigned char hz3132=/*- 文字: 迎 -*/*- 楷体_GB231224; 此字体下对应的点阵为：宽x高=32x33 -*/0x00,0x00,0x