RIP与EIGRP重分布.doc

RIP与EIGRP重分布一、 网络拓扑图二、 设备配置R1：RouterRouterenaRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hos R1R1(config)#int f 0/0R1(config-if)#ip address 192.168.1.254 255.255.255.0R1(config-if)#no shutdown R1(config-if)#exit%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upR1(config)#int s 2/0R1(config-if)#ip address 192.168.2.1 255.255.255.0R1(config-if)#clo ra 64000R1(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial2/0, changed state to downR1(config-if)#exiR1(config)#router rip R1(config-router)#ve 2R1(config-router)#network 192.168.1.0R1(config-router)#network 192.168.2.0R1(config-router)#exR1(config)#do wrBuilding configuration.OKR2:RouterRouterenaRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hos R2R2(config)#int s 2/0R2(config-if)#ip address 192.168.2.2 255.255.255.0R2(config-if)#no shutdown R2(config-if)#exit%LINK-5-CHANGED: Interface Serial2/0, changed state to upR2(config)#int s 3/0%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to upR2(config-if)#ip address 192.168.3.1 255.255.255.0R2(config-if)#clo ra 64000R2(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial3/0, changed state to downR2(config-if)#exiR2(config)#R2(config)#router rip R2(config-router)#ve 2R2(config-router)#network 192.168.2.0R2(config-router)#redistribute eigrp 1 metric 3R2(config-router)#exiR2(config)#router eigrp 1R2(config-router)#network 192.168.3.0R2(config-router)#redistribute rip metric 1000 100 1 250 150R2(config-router)#exiR2(config)#do wrBuilding configuration.OKR3:RouterRouterenaRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#int f 0/0Router(config-if)#ip address 192.168.4.254 255.255.255.0Router(config-if)#no shutdown Router(config-if)#exit%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upRouter(config)#int s 2/0Router(config-if)#ip address 192.168.3.2 255.255.255.0Router(config-if)#no shutdown Router(config-if)#exit%LINK-5-CHANGED: Interface Serial2/0, changed state to upRouter(config)#router eigrp 1Router(config-router)#network 192.168.4.0%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to upRouter(config-router)#network 192.168.3.0%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 192