HGU网管培训手册(上海贝尔).doc

BELL-HGU网管培训BELL-HGU网管培训1一.7360配置命令如下：2(一）7360创建HGU命令2（二）7360删除SFU和HGU的命令2（三）7360创建SFU的命令3（四）7360删除SFU和HGU的命令3二.7342&META配置命令如下：3（一）7342&META创建HGU的命令3（二）7342&META删除HGU的命令3（三）7342&META创建SFU的命令3(四）7342&META删除SFU的命令3三.业务VLAN的创建3(一）关于7360的vlan 创建3(二）关于7342&META的vlan 创建3(三）VLAN的透传3四.常见障碍处理命令3错误！超链接引用无效。一.7360配置命令如下：(一）7360创建HGU命令1. 配置ONT数据，LOID为CS3001configure equipment ont interface 1/1/6/10/90 sw-ver-pland disabled log-auth-id ALCLF891B7CE cvlantrans-mode localconfigure equipment ont interface 1/1/8/8/88 admin-state up2.配置ONTCARD数据，并开启。模式为VEIP模式，CARD为14，中兴，华为，烽火统一为card 14configure equipment ont slot 1/1/8/8/88/14 planned-card-type veip plndnumdataports 1 plndnumvoiceports 0 configure equipment ont slot 1/1/8/8/88/14 admin-state up 3. 配置上行速率20Mconfigure interface port uni:1/1/8/8/88/14/1 admin-upconfigure qos interface 1/1/8/8/88/14/1 upstream-queue 0 bandwidth-profile name:10M4.配置下行速率20Mconfigure qos interface 1/1/8/8/88/14/1 queue 0 shaper-profile name:10M5. 配置对应VLAN透传，49Rms管理vlan，2414:3900 为宽带管理vlan，503为语音vlanconfigure bridge port 1/1/8/8/88/14/1 max-unicast-mac 8configure bridge port 1/1/8/8/88/14/1 vlan-id 49 tag single-tagged vlan-scope local network-vlan 49configure bridge port 1/1/8/8/88/14/1 vlan-id 3138 tag single-tagged vlan-scope local network-vlan 3138configure bridge port 1/1/8/8/88/14/1 vlan-id 3900 tag single-tagged vlan-scope local network-vlan stacked:2414:3900configure bridge port 1/1/8/8/88/14/1 vlan-id 101 tag single-tagged vlan-scope local network-vlan stacked:2414:101（二）7360删除SFU和HGU的命令configure equipment ont interface 1/1/8/8/88 admin-state downconfigure equipment ont no interface 1/1/8/8/88（三）7360创建SFU的命令1、创建宽带数据configure equipment ont interface 1/1/6/10/100 sw-ver-pland DISABLED log-auth-id ALCLF891B7CE voip-allowed enableconfigure equipment ont slot 1/1/8/8/88/1 planned-card-type 10_100base plndnumdataports 2 plndnumvoiceports 0configure interface port uni:1/1/8/8/88/1/1.2 admin-upconfigure qos interface 1/1/8/8/88/1/1.2 upstream-queue 0 bandwidth-profile name:10Mconfigure qos interface 1/1/8/8/88/1/1.2 queue 0 shaper-profile name:10Mconfigure vlan id stacked:2414:3900 mode residential-bridge in-qos-prof-name name:PQ0 name HSIconfigure bridge port 1/1/8/8/88/1/1 max-unicast-mac 2configure bridge port 1/1/8/8/88/1/1 vlan-id 3900 network-vlan stacked:2414:3900 vlan-scope localconfigure bridge port 1/1/8/8/88/1/1 pvid 3900configure vlan id stacked:2414:101 mode residential-bridge in-qos-prof-name name:PQ0 name HSIconfigure bridge port 1/1/8/8/88/1/2 max-unicast-mac 2configure bridge port 1/1/8/8/88/1/2 vlan-id 101 network-vlan stacked:2414: 101vlan-scope localconfigure bridge port 1/1/8/8/88/1/2 pvid 1012、 创建语音数据configure qos interface 1/1/8/8/88/voip upstream-queue 0 priority 8 bandwidth-profile name:1M_2M_VOIPconfigure equipment ont slot 1/1/8/8/88/2 planned-card-type pots plndnumdataports 0 plndnumvoiceports 1 admin-state upconfigure bridge port 1/1/8/8/88/voipconfigure bridge port 1/1/8/8/88/voip vlan-id 3138configure bridge port 1/1/8/8/88/voip pvid 3138configure voice ont service 1/1/8/8/88/1 ip-address 0 net-mask 48 default-router mgc-ip-addr 2 sec-mgc-ip-addr vlan 3138 admin-state unlocked voip-mode softswitch-h248 conf-file-name cn+m-hrb.lzs.0+dts-4+dt-n.xmlconfigure voice ont pots 1/1/8/8/88/2/1 termination-id P1 admin-state unlockedconfigure bridge port 1/1/8/8/88/voip vlan-id 3138 static-user ip-address 0/32（四）7360删除SFU和HGU的命令configure equipment ont interface 1/1/8/8/88 admin-state downconfigure equipment ont no interface 1/1/8/8/88二.7342&META配置命令如下：（一）7342&META创建HGU的命令1.配置ONT数据，LOID为CS3001ent-ont:ont-1-1-9-4-16:LOID=4510000293780154,SWVERPLND=DISABLE,FECUP=DISABLE:IS;2.配置ONTCARD数据，并开启。模式为VEIP模式，CARD为14ENT-ONTCARD:ONTCARD-1-1-9-4-16-14:VEIP:IS; 3、 创建ONTVEIP,最大用户数量8ENT-ONTVEIP:ONTVEIP-1-1-9-4-16-14-1:NAME=,CUSTINFO=,CVLANDEF=0,SESSPROFID=11,SESSPROFNM=,MAXMACNUM=8;3.创建portal模板，引用速率模板，上行10（索引），下行11（索引）ENT-SERVICE-PORTAL:PORTAL-1-1-9-4-16-1:SVLAN=0,BWPROFUPID=200,BWPROFDNID=200; 4.配置对应VLAN透传，49Rms管理vlan，2414:3900 为宽带管理vlan，503为语音vlanENT-SERVICE-FLOW:FLOW-1-1-9-4-16-14-1-1:PORTAL=1,SVLAN=3999,PQPROFID=1,UNISIDEVLAN=2101,NETWORKSIDEVLAN=2101; ENT-SERVICE-FLOW:FLOW-1-1-9-4-16-14-1-2:PORTAL=1,SVLAN=3999,PQPROFID=1,UNISIDEVLAN=101,NETWORKSIDEVLAN=101; ENT-SERVICE-FLOW:FLOW-1-1-9-4-16-14-1-3:PORTAL=1,SVLAN=3770,PQPROFID=1,UNISIDEVLAN=2103,NETWORKSIDEVLAN=2103;ENT-SERVICE-FLOW:FLOW-1-1-9-4-16-14-1-4:PORTAL=1,SVLAN=3770,PQPROFID=10,UNISIDEVLAN=104,NETWORKSIDEVLAN=104; ENT-SERVICE-FLOW:FLOW-1-1-9-4-16-14-1-5:PORTAL=1,SVLAN=503,PQPROFID=10,UNISIDEVLAN=503,NETWORKSIDEVLAN=503; ENT-SERVICE-FLOW:FLOW-1-1-9-4-16-14-1-6:PORTAL=1,SVLAN=49,PQPROFID=10,UNISIDEVLAN=49,NETWORKSIDEVLAN=49; 5. 创建语音ARPENT-PONARPENT:PONVLAN-503:,BRGPORT-1-1-9-4-16-14-1:CVLAN=0;（二）7342&META删除HGU的命令ED-SERVICE-FLOW:FLOW-1-1-9-4-16-14-1-1&-8:OOS;DLT-SERVICE-FLOW:FLOW-1-1-9-4-16-14-1-1&-8;ED-SERVICE-PORTAL:PORTAL-1-1-9-4-16-1&-8:OOS;DLT-SERVICE-PORTAL:PORTAL-1-1-9-4-16-1&-8;ED-ONTVEIP:ONTVEIP-1-1-9-4-16-14-1:OOS;DLT-ONTVEIP:ONTVEIP-1-1-9-4-16-14-1;ED-ONTCARD:ONTCARD-1-1-9-4-16-14:OOS;DLT-ONTCARD:ONTCARD-1-1-9-4-16-14;ED-ONT:ONT-1-1-9-4-16:OOS;DLT-ONT:ONT-1-1-9-4-16;（三）7342&META创建SFU的命令1、创建宽带数据ENT-ONT:ONT-1-1-9-4-16:LOID=A00609,SWVERPLND=AUTO,RATELIMITOPT=enable:oos;ED-ONT:ONT-1-1-9-4-16:IS;ENT-ONTCARD:ONTCARD-1-1-9-4-16-1:10_100BASET:IS;ent-service-portal:portal-1-1-9-4-16-1:SVLAN=3770,BWPROFUPID=200,BWPROFDNID=200,SCHEDSERVPROFDNID=21;ent-service-portal:portal-1-1-9-4-16-2:SVLAN=3770,BWPROFUPID=200,BWPROFDNID=200,SCHEDSERVPROFDNID=21;ent-ontenet:ontenet-1-1-9-4-16-1-1:AUTODETECT=AUTO,CVLANDEF=3900,SESSPROFID=31,MAXMACNUM=128;ent-ontenet:ontenet-1-1-9-4-16-1-2:AUTODETECT=AUTO,CVLANDEF= 101,SESSPROFID=31,MAXMACNUM=128;ent-service-flow:flow-1-1-9-4-16-1-1-1:PORTAL=1,SVLAN=3770,PQPROFID=45,UNISIDEVLAN=3900,NETWORKSIDEVLAN=3900;ent-service-flow:flow-1-1-9-4-16-1-2-1:PORTAL=2,SVLAN=3770,PQPROFID=45,UNISIDEVLAN= 101,NETWORKSIDEVLAN= 101;2、创建语音数据ENT-SERVICE-VOIP:VOIP-1-1-9-4-16-1:BWPROFUPID=20,BWPROFDNID=20,PQPROFID=47,SVLAN=503,SRCVLANID=503,IPADDRLOC=46,NETMASKLOC=,DEFROUTER=,IPADDRMGC=2,IPADDRMGCSEC=2,IPADDRFTP=,VOIPMODE=SSH248,PORTMGC=2944,CONFIGFILE=cn+t-RTP/0000+dt-n+t38-n+zt-n.xml,FTPUSERNAME=ngn,FTPPASSWORD=softswitch:IS;ENT-ONTCARD:ONTCARD-1-1-9-4-16-2:pots:IS;ENT-ONTPOTS:ONTPOTS-1-1-9-4-16-2-1:VOIPSERV=1,TERMID=P1:IS;ENT-PONARPENT:PONVLAN-503:46,VOIPBRGPORT-1-1-9-4-16-1:CVLAN=0;(四）7342&META删除SFU的命令1、 删除宽带数据dlt-ponigmpchn:flow-1-1-9-4-16-1-4-1;dlt-ponigmpchn:flow-1-1-9-4-16-1-4-2;dlt-ponigmpchn:flow-1-1-9-4-16-1-2-1;dlt-ponigmpchn:flow-1-1-9-4-16-1-2-2;ed-service-flow:flow-1-1-9-4-16-1-1-1&-2:oos;ed-service-flow:flow-1-1-9-4-16-1-2-1&-2:oos;ed-service-flow:flow-1-1-9-4-16-1-3-1&-2:oos;ed-service-flow:flow-1-1-9-4-16-1-4-1&-2:oos;dlt-service-flow:flow-1-1-9-4-16-1-1-1&-2;dlt-service-flow:flow-1-1-9-4-16-1-2-1&-2;dlt-service-flow:flow-1-1-9-4-16-1-3-1&-2;dlt-service-flow:flow-1-1-9-4-16-1-4-1&-2;ed-service-portal:portal-1-1-9-4-16-1&-8:oos;dlt-service-portal:portal-1-1-9-4-16-1&-8;ed-ontenet:ontenet-1-1-9-4-16-1-1&-4:oos;dlt-ontenet:ontenet-1-1-9-4-16-1-1&-4;ed-ontcard:ontcard-1-1-9-4-16-1:oos;dlt-ontcard:ontcard-1-1-9-4-16-1;ed-ont:ont-1-1-9-4-16:oos;dlt-ont:ont-1-1-9-4-16;2、 删除语音数据ED-ONTPOTS:ONTPOTS-1-1-9-4-16-2-1&-2:OOS;DLT-ONTPOTS:ONTPOTS-1-1-9-4-16-2-1&-2;ED-ONTCARD:ONTCARD-1-1-9-4-16-2:OOS;DLT-ONTCARD:ONTCARD-1-1-9-4-16-2;ED-SERVICE-VOIP:VOIP-1-1-9-4-16-1:OOS;DLT-SERVICE-VOIP:VOIP-1-1-9-4-16-1;三.业务VLAN的创建(一）关于7360的vlan 创建1、单层VLAN，一般包括TR069的vlan，语音VLANconfigure vlan id 49 mode residential-bridge in-qos-prof-name name:PQ0 new-broadcast enableconfigure vlan id 830 mode residential-bridge in-qos-prof-name name:PQ0 new-broadcast enable2、双层VLAN，一般指宽带和IPTV业务VLANconfigure vlan id stacked:2414:0 mode residential-bridge in-qos-prof-name name:PQ0 name HSI configure vlan id stacked:2414:3900 mode residential-bridge in-qos-prof-name name:PQ0 name HSI (二）关于7342&META的vlan 创建1、单层VLAN，一般包括TR069的vlan，语音VLANENT-PONVLAN:PONVLAN-49:MODE=RBRIDGE,NAME=VLAN49,DHCPRELAY=ENABLED,TAGMODE=passthru,PPPOERELAY=DISABLED;ENT-PONVLAN:PONVLAN-503:MODE=RBRIDGE,NAME=ARPSNPG_503,DHCPRELAY=enable,TAGMODE=passthru,PPPOERELAY=DISABLED2、双层VLAN，一般指宽带和IPTV业务VLANENT-PONVLAN:PONVLAN-2414:MODE=CVLANLEARN,NAME=VLAN2414,DHCPRELAY=ENABLED,TAGMODE=STACKED;(三）VLAN的透传1、7360配置configure service vpls 49 customer 1 v-vpls vlan 49 create configure service vpls 49 sap lag-20:49 create configure service vpls 49 sap lt:1/1/1:49 create configure service vpls 49 sap lt:1/1/2:49 create configure service vpls 49 sap lt:1/1/3:49 create configure service vpls 49 sap lt:1/1/4:49 create configure service vpls 49 sap lt:1/1/5:49 create configure service vpls 49 sap lt:1/1/6:49 create configure service vpls 49 sap lt:1/1/7:49 create configure service vpls 49 sap lt:1/1/8:49 create configure service vpls 49 no shutdownconfigure service vpls 830 customer 1 v-vpls vlan 830 createconfigure service vpls 830 sap nt-a:xfp:3:830 create configure service vpls 830 sap lt:1/1/1:830 create configure service vpls 830 sap lt:1/1/2:830 create configure service vpls 830 sap lt:1/1/3:830 create configure service vpls 830 sap lt:1/1/4:830 create configure service vpls 830 sap lt:1/1/5:830 create configure service vpls 830 sap lt:1/1/6:830 create configure service vpls 830 sap lt:1/1/7:830 create configure service vpls 830 sap lt:1/1/8:830 create configure service vpls 830 no shutdownconfigure service vpls 2414 customer 1 v-vpls