跨阻抗放大器.docx

Transimpedance amplifierFrom Wikipedia, the free encyclopediaFig. 1. Simplified transimpedance amplifierInelectronics, atransimpedanceamplifier(TIA) is a current-to-voltage converter, most often implemented using anoperational amplifier. The TIA can be used to amplify1the current output ofGeigerMller tubes, photo multiplier tubes,accelerometers, photo detectors and other types of sensors to a usable voltage. Current-to-voltage converters are used with sensors that have a current response that is more linear than the voltage response. This is the case withphotodiodeswhere it is not uncommon for the current response to have better than 1% linearity over a wide range of light input. The transimpedance amplifier presents a low impedance to the photodiode and isolates it from the output voltage of the operational amplifier. In its simplest form a transimpedance amplifier has just a large valued feedback resistor, Rf. The gain of the amplifer is set by this resistor and because the amplifier is in an inverting configuration, has a value of Rf. There are several different configurations of transimpedance amplifiers, each suited to a particular application. The one factor they all have in common is the requirement to convert the low-level current of a sensor to a voltage. The gain, bandwidth, as well as current and voltage offsets change with different types of sensors, requiring different configurations of transimpedance amplifiers.In the circuit shown in Fig. 1 the photodiode is connected between ground and the inverting input of the op-amp. The other input of the op-amp is also connected to ground. This provides a low impedance load for the photodiode, which keeps the photodiode voltage low. The photodiode is operating in photovoltaic mode with no external bias. The high gain of the opamp keeps the photodiode current equal to the feedback current through Rf. The input offset voltage due to the photodiode is very low in this self-biased photovoltaic mode. This permits a large gain without any large output offset voltage. This configuration is used with photodiodes that are illuminated with low light levels and require a lot of gain.Fig. 2. Transimpedance amplifier with a reverse biased photodiode The above equation is the DC and low frequency gain of a transimpedance amplifier. If the gain is large anyinput offset voltageat the non-inverting input of the opamp will result in an output DC offset. An input bias current on the inverting terminal of the opamp will similarly result in an output offset. To minimize these effects transimpedance amplifiers are usually designed with FET input op-amps that have very low input offset voltages.3Fig. 2 shows a inverting TIA with the photodiode driven by a laser diode and operating in thephotoconductivemode. A positive voltage at the cathode of the photodiode applies a reverse bias. This reverse bias increases the width of the depletion region and lowers the junction capacitance, improving the high frequency performance. The photoconductive configuration of a transimpedance photodiode amplifier is used where fast switching speed is required but high gain is not. The feedback capacitor, Cfis usually required to improve stability.Bandwidth and stabilityFig. 3. Incremental model showing sensor capacitanceThe frequency response of a transimpedance amplifier is inversely proportional to the gain set by the feedback resistor. The product of the gain, Vin/Vo, is very close to being a constant for any given op-amp. The sensors that transimpedance amplifiers are used with usually have more capacitance than an op-amp can handle. Fig. 3 models the sensor as a current source and a capacitor, Ci.4This capacitance across the input terminals of the op-amp, which includes the internal capacitance of the op-amp, introduces a low-pass filter in the feedback path. The low pass response of this filter can be characterized as the feedback factor , which attenuates the feedback signal. This places a greater demand on the amplifier gain.where is the reactance of the capacitance Ci.When the effect of this low-pass filter response is considered, the circuits response equation becomes the following:Where is the open loop gain of the op-amp.Fig. 4. Bode plot of uncompensated transimpedance amplifier5At low frequencies the feedback factor, , has little effect on the amplifier response. The amplifier response will be close to the ideal,as long as the loop gain,is much greater than unity. TheBode plotof a transimpedance amplifier with no compensation is shown in Fig. 4. The vertical axis represents logarithmic gain and the horizontal axis the log of frequency. The flat curve with the peak, labeled I-TO-V GAIN, is the frequency response of the transimpedance amplifier. The peaking of the gain curve is typical of uncompensated or poorly compensated transimpedance amplifiers. The curve labeled AOLis the open-loop response of the amplifier. The feedback factor, plotted as a reciprocal, is labeled 1/. In Fig. 5 the 1/ curve and AOLform an equilateral triangle with the frequency axis. The two sides have equal but opposite slope since one is the result of a first orderpoleand the other a first orderzero. Each slope has a magnitude of 20 dB/decade, corresponding to a phase shift of 90. When the amplifiers 180 of phase inversion is added to this the result is a full 360 at the fiintercept, indicated by the dashed vertical line. At that intercept 1/ = AOL, for a loop gain of AOL = 1. Oscillation will occur at the fifrequency because of the 360 phase shift, or positive feedback, and the unity gain.6To mitigate these effects, designers of transimpedance amplifiers add a small value compensating capacitor. Fig. 3 shows a capacitor, Cfin parallel with the feedback resistor. When this feedback capacitor is considered, the compensated feedback factor becomes:The feedback capacitor produces a zero, or deflection in the response curve, at the frequencyThis counteracts the pole produced by Ciat the frequencyFig. 5. Bode plot of compensated transimpedance amplifier7Fig. 5 shows the bode plot of a transimpedance amplifier that has a compensation capacitor in the feedback path, as shown in Fig. 3. The compensated feedback factor, plotted as a reciprocal, 1/, starts to roll off before fi, reducing the slope at the intercept. The loop gain is still unity but the total phase shift is not a full 360. One of the requirements for oscillation is eliminated with the addition of the compensation capacitor and so