SIEI变频器参数设置一览表

SIEI 变频器参数设置一览表 OH CON 以 1 0m s 载重 1000kg 平衡系数 45 变频器 11kw 电动机 8 5kw 13VTR 为例 菜单 参数设定值备注菜单 参数设定值备注 Starup Regulation mode Speed reg gains Regulation Mode Field oriented SpdP1 gain 20 00 SpdI1 gain 10 00 Starup Starup config setup mode Drive data SpdP2 gain 20 00 Main voltage 400 380VDefault SpdI2 gain 20 00 Ambient temp 40 度 Default Speed thresholds Switching freq 8kDefault Spd 0 ref thr 5rpm Spd ref fbk res 0 125 Spd 0 ref delay 500msDefault Setup mode Motor data Spd 0 speed thr 5rpm Rated voltage 380V 主机参 数 Spd 0 spd delay 500msDefault Rated frequency 50Hz SGP tran21 h thr 15 00 Rated current 20A SGP tran32 I thr 0 00 Rated speed1462rpm SGP tran 21 band 10 00 Rated power8 5kw SGP tran32 band 0 00 Cosfi0 76 Pre torque Effocoemcy80 Int pre torque 0 Startup Startup config Mechanical Pre torque src Int pre torque Travel units sel Millimeter REGULATION PARAM Spd regulator Spdregulator base values Gearbox ratio 44 SpdP base value 3A rpm Pulley diameter 575mm SpdI base value 93 6A rpm s Full scale speed 1500rpm I O CONFIG Analog inputs Std analog inps Analog input 2 An inp 2 cfg Weights An inp 2 thr 10000cnt Cabin weight 1200 kg An inp 2 scale 1 若抱闸反 馈接常开 触点 则 参数值为 负 Counter weight 1650 kg 根据 P Q 情 况酌情 调整 Digital inputs Std digital inps Std dig inp cfg Load weight1000kg 额定载 重 DI 3 inversion Inverted Default Landing zone Digital outputs Std digital outs Std dig out src Landing control Enabled DO 0 srcDrive OK 端子 80 82 Landing init src DI 7 monitor 端子 39 DO 1 src BRAKE cont mon 端子 83 85 Landing distance 70 mm DO 2 src RUN cont mon 端子 41 46 Pos speed limit 20rpm DO 3 src Door open mon 端子 42 46 Encoders config Speed fbk sel Std encoder ALARM CONFIG Undervoltage Std enc type Digital UV restart On Std enc pulses 1024ppr UV restart 5000ms Std dig enc mode FP mode Default External fault Std enc supply 6 16V EF src Compare 2 output Std sin enc type 0 5VDefault EF activity Disable drive SpdReg gain calc 勿改此 菜单参 数 EF restart Off Calc method Variable bandw Default EF hold off 2000ms BU protection Contact feedback BU controlInternal Default CNT feedback src DI 3 monitor 端子 15 BU resistance 50 CNT activity Disable drive BU res cont pwr 2Kw CNT hold off 800ms Brake feedback TRAVEL Speed profile BRK feedback src An inp 2 thr Multi speed 1 1000mm s 额定速 度 BRK activity Disable drive Multi speed 2 50mm s 爬行速 度 BRK hold off 1000ms Multi speed 3 200mm s 检修速 度 Drive overload Ramp profile DOL activity Disable drive MR0 acc ini jerk 250 mm s3 Overspeed MR0 acceleration 600 mm s2 OS activity Disable drive MR0 acc end jerk 650 mm s3 OS threshold 1500rpm MR0 dec ini jerk 650 mm s3 OS hold off 0ms MR0 deceleration 650 mm s2 UV repetitive MR0 dec end jerk 630 mm s3 UVR attempts 3 Mr0 end decel 580 mm s2 UVR delay10s Lift sequence Cont close delay 200ms CUSTOM FUNCTION Compare Compare 1 Compare 1 src Brake open delay 304ms Cmp 1 inp 0 src Speed ref Brake close dly 200ms Cmp 1 inp 1 src Norm Speed Cont open delay 304ms Compare 1 cfg Start fwd src DI 1 monitor 端子 13 Spd ref fbk res I0 I1 Start rev src DI 2 monitor 端子 14 Cmp 1 inversion Not inverted Default Mlt spd s 0 src DI 4 monitor 端子 36 Compare 2 Compare 2 src Mlt spd s 1 src DI 5 monitor 端子 37 Cmp 2 inp 0 src Compare 1 output Door open src DI 7 monitor 端子 39 Cmp 2 inp 1 src DI 0 Enable mon Door fbk src DI 6 monitor 端子 38 Cmp 2 inp 2 src ONE Door