TRT程序.doc

1 STARTSTOP：验*)TestRS( Set := Test_Set, R1 := Test_Reset or Stop_Reset, Q1 = Test_Status );(*启动条件具备*)Start_Allow:=not PE511_L and not PE401_LL and not PI601_L and PSA413 and PSA303 and PSB303 and PdS524 and not Stop_Signal and PE301_H;(*透平申请启动*)StartApplyRS( Set := Start_Allow and Start_Apply, R1 := Stop_Signal or Start_Cancel, Q1 = PDC429 );(*PDC438:=PDC429 and (SE801C_H or SE801A_H or SE801B_H);*)(*系统闭锁解除*)SystermReleaseRS( Set := PDC429 and Start_Allow and PdS567, R1 := Stop_Signal, Q1 = SystermInterlock_Release );(*透平停机条件*)(*透平前轴振动A*)StopSignalRS1( Set := XT801A_HH, R1 := Stop_Reset, Q1 = StopSignal_Cond1 );(*透平前轴振动B*)StopSignalRS16( Set := XT801B_HH, R1 := Stop_Reset, Q1 = StopSignal_Cond16 );(*透平后轴振动A*)StopSignalRS17( Set := XT802A_HH, R1 := Stop_Reset, Q1 = StopSignal_Cond17 );(*透平后轴振动B*)StopSignalRS18( Set := XT802B_HH, R1 := Stop_Reset, Q1 = StopSignal_Cond18 );(*发电机前轴振动B*)StopSignalRS19( Set := XT803B_HH, R1 := Stop_Reset, Q1 = StopSignal_Cond20 );(*发电机前轴振动A*)StopSignalRS2( Set := XT803A_HH , R1 := Stop_Reset, Q1 = StopSignal_Cond2 );(*透平位移A*)StopSignalRS3( Set := ZT801A_HH OR ZT801A_LL, R1 := Stop_Reset, Q1 = StopSignal_Cond3 );(*透平位移B*)StopSignalRS20( Set := ZT801B_HH OR ZT801B_LL, R1 := Stop_Reset, Q1 = StopSignal_Cond20 );(*透平转速*)StopSignalRS4( Set := (SE801A_HH AND SE801B_HH) OR (SE801B_HH AND SE801C_HH) OR (SE801C_HH AND SE801A_HH), R1 := Stop_Reset, Q1 = StopSignal_Cond4 );(*润滑油*)StopSignalRS5( Set := PE401_LL or (PS402A and PS402B) or (PS402A and PS402C) or (PS402B and PS402C), R1 := Stop_Reset, Q1 = StopSignal_Cond5 );(*液压油*)StopSignalRS6( Set := PE511_LL, R1 := Stop_Reset, Q1 = StopSignal_Cond6 );(*透平前轴温度A*)StopSignalRS7( Set := PE201A_HH , R1 := Stop_Reset, Q1 = StopSignal_Cond7 );(*透平前轴温度B*)StopSignalRS21( Set := PE201B_HH , R1 := Stop_Reset, Q1 = StopSignal_Cond21 );(*透平后轴温度A*)StopSignalRS22( Set := PE202A_HH , R1 := Stop_Reset, Q1 = StopSignal_Cond22 );(*透平后轴温度B*)StopSignalRS23( Set := PE202B_HH , R1 := Stop_Reset, Q1 = StopSignal_Cond23 );(*发电机前轴温度*)StopSignalRS8( Set := TISA206_HH , R1 := Stop_Reset, Q1 = StopSignal_Cond8 );(*发电机后轴温度*)StopSignalRS24( Set := TISA207_HH , R1 := Stop_Reset, Q1 = StopSignal_Cond24 );stop_ftrig( Clk := PdS565 );StopSignalRS10( Set := PdS560 or stop_ftrig.Q , R1 := Stop_Reset, Q1 = StopSignal_Cond10 );(*氮气支管压力*)StopSignalRS11( Set := PI601_LL, R1 := Stop_Reset, Q1 = StopSignal_Cond11 );(*紧急停车*)StopSignalRS12( Set := StopSignal_Set OR PDS100, R1 := Stop_Reset, Q1 = StopSignal_Cond12 );(*透平前止推轴温度A*)StopSignalRS13( Set := PE203A_HH , R1 := Stop_Reset, Q1 = StopSignal_Cond13 );(*透平前止推轴温度B*)StopSignalRS9( Set := PE203B_HH, R1 := Stop_Reset, Q1 = StopSignal_Cond9 );(*透平后止推轴温度A*)StopSignalRS24( Set := PE204A_HH , R1 := Stop_Reset, Q1 = StopSignal_Cond24 );(*透平后止推轴温度B*)StopSignalRS25( Set := PE204B_HH, R1 := Stop_Reset, Q1 = StopSignal_Cond25 );(*快切阀关*)QuickCloseRtrig( Clk := PdS521 );StopSignalRS15( Set := QuickCloseRtrig.Q , R1 := Stop_Reset, Q1 = StopSignal_Cond15 );Stop_Signal1:=StopSignal_Cond1 or StopSignal_Cond2 or StopSignal_Cond3 or StopSignal_Cond4 or StopSignal_Cond5 or StopSignal_Cond6 or StopSignal_Cond7 or StopSignal_Cond8 or StopSignal_Cond9 ;Stop_Signal2:=StopSignal_Cond11 or StopSignal_Cond12 or StopSignal_Cond13 or StopSignal_Cond10 or StopSignal_Cond14 or StopSignal_Cond15 or StopSignal_Cond16 or StopSignal_Cond19 or StopSignal_Cond17 or StopSignal_Cond18 ;Stop_Signal3:=StopSignal_Cond21 or StopSignal_Cond22 or StopSignal_Cond23 or StopSignal_Cond24 or StopSignal_Cond25 or StopSignal_Cond26 or StopSignal_Cond27 or StopSignal_Cond20;Stop_Signal:=Stop_Signal1 or Stop_Signal2 or Stop_Signal3;PDC434:=Stop_Signal;PDC436:=Stop_Signal;(*if Stop_Signal then FIC101.Value:=0;end_if;*)StopSignalNormalRS( Set := StopSignal_Normal, R1 := Stop_Reset, Q1 = PDC433 );2 PUMP：(*润滑油辅泵控制*) LubOilAidPump_RS( Set := LubOilAidPump_Start or PE401_l, R1 := LubOilAidPump_Stop or not PdS530, Q1 = PDC401 ); (*润滑油排雾风机启停*)LubOilFan_RS( Set := LubOilFan_Start, R1 := LubOilFan_Stop or not PdS531, Q1 = PDC402 );(*润滑油电加热器启停*)LubOilHeater_RS( Set := LubOilHeater_Start or TIA401_L, R1 := LubOilHeater_Stop or TIA401_H or not PdS532, Q1 = PDC403 );(*液压油1号泵启停*)HydOilPump1_RS( Set := HydOilPump1_Start or PE511_L, R1 := HydOilPump1_Stop or not PdS539 , Q1 = PDC404 );(*液压油2号泵启停*)HydOilPump2_RS( Set := HydOilPump2_Start or PE511_L, R1 := HydOilPump2_Stop or not PdS540 , Q1 = PDC405 );(*液压油电加热器启停*)HydOilHeater_RS( Set := HydOilHeater_Start or TI511_L, R1 := HydOilHeater_Stop or not PdS541 or TI511_H or LE511_L, Q1 = PDC406 );(*液压油自过滤泵启停*)HydOilFilter_RS( Set := HydOilFilter_Start, R1 := HydOilFilter_Stop or not PdS542, Q1 = PDC407 );(*盘车电机启停*)TurningMotor_RS( Set := TurningMotor_Start, R1 := TurningMotor_Stop or not PdS554 or (SE801A50) and (SE801B50) or (SE801B50) and (SE801C50) or (SE801A50) and (SE801C50) or PE401_L , Q1 = PDC416 );3 AIAlarm：(*主油泵出油压力报警*)PE401_LevelL( Enable := 1, In := PE402, Hysteresis := 0.01, Level1 := 0.05, InLtLevel1 = PE401_LL, Level2 := 0.12, InLtLevel2 = PE401_L );(*液压油总管出口压力报警*)PE511_LevelLL( Enable := 1, In := PE511, Hysteresis := 0.1, Level1 := 8, InLtLevel1 = PE511_LL );PE511_LevelL( Enable := 1, In := PE511, Hysteresis := 0.1, Level1 := 11, InLtLevel1 = PE511_L );(*静叶开度报警*)VZ512_LevelL( Enable := 1, In := VZ512, Hysteresis := 0.2, Level1 := 0, InLtLevel1 = VZ512_L );(*氮气支管压力低报警*)PI601_LevelL( Enable := 1, In := PI601, Hysteresis := 0.01, Level1 := 0.3, InLtLevel1 = PI601_L, Level2 := 0.2, InLtLevel2 = PI601_LL );PI601_LevelH( Enable := 1, In := PI601, Hysteresis := 0.02, Level1 := 0.32, InGtLevel1 = PI601_H );(*透平超速*)SE801A_LevelH( Enable := 1, In := SE801A, Hysteresis := 5, Level1 := 3150, InGtLevel1 = SE801A_HH, Level2 := 3100, InGtLevel2 = SE801A_H );(*透平超速*)SE801B_LevelH( Enable := 1, In := SE801B, Hysteresis := 5, Level1 := 3150, InGtLevel1 = SE801B_HH, Level2 := 3100, InGtLevel2 = SE801B_H );(*透平超速*)SE801C_LevelH( Enable := 1, In := SE801C, Hysteresis := 5, Level1 := 3150, InGtLevel1 = SE801C_HH, Level2 := 3100, InGtLevel2 = SE801C_H );(*透平前轴振动A报警*)XT801A_LevelH( Enable := 1, In := XT801A, Hysteresis := 1, Level1 := 120, InGtLevel1 = XT801A_HH, Level2 := 80, InGtLevel2 = XT801A_H );(*透平前轴振动B报警*)XT801B_LevelH( Enable := 1, In := XT801B, Hysteresis := 1, Level1 := 120, InGtLevel1 = XT801B_HH, Level2 := 80, InGtLevel2 = XT801B_H);(*透平后轴振动A报警*)XT802A_LevelH( Enable := 1, In := XT802A, Hysteresis := 1, Level1 := 120, InGtLevel1 = XT802A_HH, Level2 := 80, InGtLevel2 = XT802A_H );(*透平后轴振动B报警*)XT802B_LevelH( Enable := 1, In := XT801B, Hysteresis := 1, Level1 := 120, InGtLevel1 = XT802B_HH, Level2 := 80, InGtLevel2 = XT802B_H );(*透平位移A报警*)ZT801A_LevelH( Enable := 1, In := ZT801A, Hysteresis := 0.01, Level1 := 0.5, InGtLevel1 = ZT801A_HH, Level2 := 0.3, InGtLevel2 = ZT801A_H );(*透平位移B报警*)ZT801B_LevelH( Enable := 1, In := ZT801B, Hysteresis := 0.01, Level1 := 0.5, InGtLevel1 = ZT801B_HH, Level2 := 0.3, InGtLevel2 = ZT801B_H );(*透平位移A报警*)ZT801A_LevelL( Enable := 1, In := ZT801A, Hysteresis := 0.01, Level1 := -0.5, InLtLevel1 = ZT801A_LL, Level2 := -0.3, InLtLevel2 = ZT801A_L );(*透平位移B报警*)ZT801B_LevelL( Enable := 1, In := ZT801B, Hysteresis := 0.01, Level1 := -0.5, InLtLevel1 = ZT801B_LL, Level2 := -0.3, InLtLevel2 = ZT801B_L );(*发电机前轴振动A报警*)XT803A_LevelH( Enable := 1, In := XT803A, Hysteresis := 1, Level1 := 120, InGtLevel1 = XT803A_HH, Level2 := 80, InGtLevel2 = XT803A_H );(*发电机前轴振动B报警*)XT803B_LevelH( Enable := 1, In := XT803B, Hysteresis := 1, Level1 := 120, InGtLevel1 = XT803B_HH, Level2 := 80, InGtLevel2 = XT803B_H );(*透平前轴承温度A报警*)PE201A_LevelH( Enable := 1, In := PE201A, Hysteresis := 1, Level1 := 75, InGtLevel1 = PE201A_HH, Level2 := 70, InGtLevel2 = PE201A_H );(*透平前轴承温度B报警*)PE201B_LevelH( Enable := 1, In := PE201B, Hysteresis := 1, Level1 := 75, InGtLevel1 = PE201B_HH, Level2 := 70, InGtLevel2 = PE201B_H );(*透平后轴承温度A报警*)PE202A_LevelH( Enable := 1, In := PE202A, Hysteresis := 1, Level1 := 75, InGtLevel1 = PE202A_HH, Level2 := 70, InGtLevel2 = PE202A_H );(*透平后轴承温度B报警*)PE202B_LevelH( Enable := 1, In := PE202B, Hysteresis := 1, Level1 := 75, InGtLevel1 = PE202B_HH, Level2 := 70, InGtLevel2 = PE202B_H );(*透平前止推轴承温度A报警*)PE203A_LevelH( Enable := 1, In := PE203A, Hysteresis := 1, Level1 := 75, InGtLevel1 = PE203A_HH, Level2 := 70, InGtLevel2 = PE203A_H );(*透平前止推轴承温度B报警*)PE203B_LevelH( Enable := 1, In := PE203B, Hysteresis := 1, Level1 := 75, InGtLevel1 = PE203B_HH, Level2 := 70, InGtLevel2 = PE203B_H );(*透平后止推轴承温度A报警*)PE204A_LevelH( Enable := 1, In := PE204A, Hysteresis := 1, Level1 := 75, InGtLevel1 = PE204A_HH, Level2 := 70, InGtLevel2 = PE204A_H );(*透平后止推轴承温度B报警*)PE204B_LevelH( Enable := 1, In := PE204B, Hysteresis := 1, Level1 := 75, InGtLevel1 = PE204B_HH, Level2 := 70, InGtLevel2 = PE204B_H );(*快切阀门油压低*)PE512_LevelL( Enable := 1, In := PE512, Hysteresis := 0.2, Level1 := 2, InLtLevel1 = PE512_L );(*润滑油箱温度高*)TIA401_LevelH( Enable := 1, In := TIA401, Level1 := 40, InGtLevel1 = TIA401_H );TIA401_LevelL( Enable := 1, In := TIA401, Level1 := 15, InLtLevel1 = TIA401_L );(*润滑油箱液位低*)LE401_LevelL( Enable := 1, In := LE401, Level1 := 200, InLtLevel1 = LE401_L );(*液压油箱温度高*)TI511_LevelH( Enable := 1, In := TI511, Level1 := 40, InGtLevel1 = TI511_H );TI511_LevelL( Enable := 1, In := TI511, Level1 := 20, InLtLevel1 = TI511_L );(*液压油箱液位低*)LE511_LevelL( Enable := 1, In := LE511, Level1 := 15, InLtLevel1 = LE511_L );(*高炉顶压*)DingYaCL1_LevelH( Enable := 1, In := DingYaCL1, Hysteresis := 1, Level1 := 180, InGtLevel1 = DingYaCL1_H, Level2 := 220, InGtLevel2 = DingYaCL1_HH );DingYaCL2_LevelH( Enable := 1, In := DingYaCL2, Hysteresis := 1, Level1 := 180, InGtLevel1 = DingYaCL2_H, Level2 := 220, InGtLevel2 = DingYaCL2_HH ); (*透平入口煤气*)PE102_LevelH( Enable := 1, In := PE102, Hysteresis := 1, Level1 := 120, InGtLevel1 = PE102_H, Level2 := 200, InGtLevel2 = PE102_HH );(*发电机定子温度*)TISA205_1LevelH( Enable := 1, In := TISA205_1, Hysteresis := 1, Level1 := 130, InGtLevel1 = TISA205_1HH, Level2 := (80+TISA208A), InGtLevel2 = TISA205_1H );TISA205_2LevelH( Enable := 1, In := TISA205_2, Hysteresis := 1, Level1 := 130, InGtLevel1 = TISA205_2HH, Level2 := (80+TISA208A), InGtLevel2 = TISA205_2H );TISA205_3LevelH( Enable := 1, In := TISA205_3, Hysteresis := 1, Level1 := 130, InGtLevel1 = TISA205_3HH, Level2 := (80+TISA208A), InGtLevel2 = TISA205_3H );TISA205_4LevelH( Enable := 1, In := TISA205_4, Hysteresis := 1, Level1 := 130, InGtLevel1 = TISA205_4HH, Level2 := (80+TISA208A), InGtLevel2 = TISA205_4H );TISA205_5LevelH( Enable := 1, In := TISA205_5, Hysteresis := 1, Level1 := 130, InGtLevel1 = TISA205_5HH, Level2 := (80+TISA208A), InGtLevel2 = TISA205_5H );TISA205_6LevelH( Enable := 1, In := TISA205_6, Hysteresis := 1, Level1 := 130, InGtLevel1 = TISA205_6HH, Level2 := (80+TISA208A), InGtLevel2 = TISA205_6H );TISA205_7LevelH( Enable := 1, In := TISA205_7, Hysteresis := 1, Level1 := 130, InGtLevel1 = TISA205_7HH, Level2 := (80+TISA208A), InGtLevel2 = TISA205_7H );TISA205_8LevelH( Enable := 1, In := TISA205_8, Hysteresis := 1, Level1 := 130, InGtLevel1 = TISA205_8HH, Level2 := (80+TISA208