scop 定向井 资料 中英(1).doc

Shandong Kerui International Oil & Gas Engineering Co., LTd Address: No. 233, Naner Road, Dongying, Shandong, PRC 257067Tel: +86-546-7773321 E-mail: ogsales Fax: +86-546-7773321 Content1. Well Information.22. Equipment Requirement.23. Service Base.84. Reliability Record .85. New Technology.96. Tool Operating Parameters.96.1.1 Down Hole Motor For 23-1/2 Hole Size.96.1.2 Down Hole Motor For 17 1/2 Hole Size.96.1.3 Down Hole Motor For 12 1/4 Hole Size.106.1.4 Down Hole Motor For 8 3/8 Hole Size.106.2.1 MWD & Gamma Ray For Hole Size 23 1/ MWD & Gamma Ray For Hole Size 17 1/ MWD & Gamma Ray For Hole Size 12 1/ MWD & Gamma Ray For Hole Size 8 1/2.141. Well InformationThe Well Information is provided in Geological and Drilling Program (Document attached PH14/South Pars)2. Equipment RequirementsThe Contractor shall provide on request all the equipment as follows for two jobs simultaneous on two Drilling Rigs: Mud Motors Measuring While Drilling with Gamma Ray (Optional) Drilling Jar Stabilizers NMDC (Optional) HWDP Logging While Drilling (Optional) Gyroscopic Survey Tools Jar Accelerator Torque Reducer (Optional) RSS (Optional) Roller Reamer Shock Sub (Optional) Circulating Sub (Optional)Contractor is requested to provide the equipment listed herein in accordance with the relevant applicable technical specifications. Anyhow based on the scope of requested service and according for the program as specified in information provided by Company (south pars/PH14), Contractor is free to propose alternatives and/or deletion/integration of items requested herein, provided that the tender requirements as per notes; please complete the Equipment required Table. Contractor shall provide copy of the technical specification sheet for all equipment offered. Contractor shall state his availability to provide quantity enough to accomplish with work requirements, maintenance and all consumables, replacement/spare parts necessary to fulfill the equipments requirements. Contractor shall acknowledge and state compliance with technical requirements as per the applicable technical specifications document. In case, Contractor shall Cleary indicate non-conformance of alternatives. (+) To be specified by contractor Required: means item that contractor shall be able to supply on request for each job (one Rig) Optional: Means item that contractor may or may not have available in its stock. Contractor shall state, in contract offer, whether optional items are included or not in tender offer.ItemDescriptionUnitCompany RequestContractor Offer1Down Hole Tools-1.1Roller Reamers and Relevant Spare PartsOptional-1.1.1OD Size 16-17 Optional As Req. (2)Equipped already1.1.2Make(+)Grant Petroleum Tool Company-USA1.1.3Type(+)17 1.2AIntegral Blade Stabilizers (String Stabilizer)Provided by the contractor1.2.1AOD Size 22 - 23 1/2Min. Required (2)Equipped already1.2.2AOD Size 14 1/2 - 17 Min. Required (2)Equipped already1.2.3AOD Size 11 1/2 - 12 1/4 Min. Required (2)Equipped already1.2.4AOD Size 7 1/2 - 8 1/2Min. Required (2)Equipped already1.2.5AMakeGrant Petroleum Tool Company-USA1.2.6ATypeIntegral Spiral Type1.2BIntegral Blade Stabilizers(Near Bit Stabilizer)Min. Required (2)Equipped already1.2.1BOD Size 22 1/2 - 23 1/2Min. Required (2)Equipped already1.2.2BOD Size 17 Min. Required (2)Equipped already1.2.3BOD Size 12 1/4 Min. Required (2)Equipped already1.2.4BOD Size 8 1/2Min. Required (2)Equipped already1.2.5BMake(+)North Shuangjia-CN1.2.6BType(+)Integral Spiral Type1.3Non Magnetic Drill CollarsProvided by the contractor1.3.1OD 9 1/2 x 30 LengthRequired (2)SMFI Nonmagnetic steel1.3.2OD 8 x 30 LengthRequired (2)SMFI Nonmagnetic steel1.3.3OD 6 3/4 x 30 LengthRequired (2)SMFI Nonmagnetic steel1.3.4Make(+)Grant Petroleum Tool Company-USA1.3.5Type(+)SMFI Nonmagnetic steel1.4Heavy Weight Drill PipeRequired (2)Provided by the well drilling team1.4.1OD 5 1/2 Required (2)1.4.2Make(+)Grant Petroleum Tool Company-USA(if provided by the contractor)1.4.3Type(+)S135(if provided by the contractor)1.5Drilling JarsRequired (2)Provided by the contractor1.5.1OD 9 1/2 Required (2)QJ241K(if provided by the contractor)1.5.2OD 8 Required (2)QJ203K(if provided by the contractor)1.5.3OD 6 3/4 Required (2)QJ170K(if provided by the contractor)1.5.4Make(+)Halliburton Company1.5.5Type(+)QJ1.6Shock SubProvided by the contractor1.6.1OD 9 1/2 OptionalModel: YBJ241B(if provided by the contractor)1.6.2OD 8 Optional As Req. (2)Model: YBJ203B(if provided by the contractor)1.6.3OD 6 3/4 Optional As Req. (2)Model: YBJ170B(if provided by the contractor)1.6.4Make(+)Halliburton Company1.6.5Type(+)YBJ1.7Subs (X- Over, )OptionalProvided by the contractor1.7.1For all Group 1 ItemsOptional As Req. (15)Equipped already1.8Other Down Hole Tools (Supplier to Specify)Specify2Mud Motors & DD Tools2.1Mud MotorsProvided by the contractor2.1.1OD 9 1/2 OR 9 5/8Required (3)PDM9 1/22.1.2OD 8 Required (3)PDM82.1.3OD 6 3/4 OR 6 1/2 Required (3)PDM 6 3/42.1.4Make(+)Weatherford company2.1.5Type(+)PDM2.2Circulating Sub (Multi Actived)OptionalProvided by the well drilling team2.2.1OD 9 1/2 OR 9 5/8Optional As Req. (2)DGXJ241(if provided by the contractor)2.2.2OD 8 Optional As Req. (2)DGXJ203(if provided by the contractor)2.2.3OD 6 3/4 Optional As Req. (2)DGXJ170(if provided by the contractor)2.2.4Make(+)haliburton (if provided by the contractor)2.2.5Type(+)DGXJ(if provided by the contractor)2.3Other DD Equipment (Supplier to Specify)Specify 3MWD With Gamma RayProvided by the contractor3.1For Nominal Hole Size 23 1/2Required (2)MWD3.2For Nominal Hole Size 17 1/2Required (2)MWD3.3For Nominal Hole Size 12 1/4Required (2)MWD3.4For Nominal Hole Size 8 1/2Required (2)MWD3.5Make(+)Geolink Negative3.6Type(+)MWD4Logging While Drilling (LWD)( Optional )LWD4.1DensityOptionalLWD4.1.1For Nominal Hole Size 12 1/4Optional As Req. (2)LWD4.1.2For Nominal Hole Size 8 1/2Optional As Req. (2)LWD4.1.3Make(+)Geolink Negative4.1.4Type(+)LWD4.2ResistivityOptionalLWD4.2.1For Nominal Hole Size 12 1/4Optional As Req. (2)LWD4.2.2For Nominal Hole Size 8 1/2Optional As Req. (2)LWD4.2.3Make(+)Geolink Negative4.2.4Type(+)LWD4.3Gamma RayOptionalLWD4.3.1For Nominal Hole Size 12 1/4Optional As Req. (2)LWD4.3.2For Nominal Hole Size 8 1/2Optional As Req. (2)LWD4.3.3Make(+)Geolink Negative4.3.4Type(+)LWD4.4SonicOptionalLWD4.4.1For Nominal Hole Size 12 1/4Optional As Req. (2)LWD4.4.2For Nominal Hole Size 8 1/2Optional As Req. (2)LWD4.4.3Make(+)Geolink Negative4.4.4Type(+)LWD5GYRORequired (2)Scientific Drilling5.1For Nominal Hole Size 23 1/2 Required (2)Equipped already5.2Make(+)5.3Type(+)Keeper6Jar AcceleratorRequired (2)Provided by the contractor6.1OD 8 Required (2)Model: ZJS203B (if provided by the contractor)6.2OD 6 1/2 Required (2)Model: ZJS165B(if provided by the contractor)6.3Make(+)haliburton6.4Type(+)ZJS (if provided by the contractor)2.1 Mud MotorsContractor shall provide down hole motors for directional drilling for: Minimization of trip Maximization of penetration rates as per drilling program Provide adequate spare parts for all the equipment to be used in connection with the directional drilling operations and Maintenance of tools and back ups. Contractor shall provide down hole motor with high performance2.2 Measuring While Drilling (MWD) with Gamma Ray Contractor shall provide MWD with Gamma Ray Equipment With regards to equipped NIDC with Geolink Negative MWD System; perfectly, contractor will be supplied Geolink Negative MWD System. But if Contractor could not supply Geolink Negative MWD System, other MWD system is acceptable that: Contractor shall provide and certified for 8 NIDCs Experts for running MWD. NIDC will not any charges to contractor for Personnel (For Geolink Type or other types) Accuracy and frequency documents shall provide. Contractor shall provide quality assurance, quality control and calibration documentation for all the equipment. Contractor shall provide MWD for directional drilling for: Minimization of trip-Provide adequate spare parts for all the equipment to be used in connection with the directional drilling operations, Maintenance and Calibration of tools and backups.3. Service Base Contractor shall guarantee base availability in the Kish Island with the main following: Adequate inventory of equipment and relevant consumable and spare parts General Maintenance and repairs of the equipment Sensors calibration Inspection of the equipment prior each job at rig siteContractor BasePurpose of FacilityLocationDescription Major EquipmentsStorage of equipment and spare partsMaintenance of down hole tools and auxiliary equipmentStorage of spare equipmentCalibration of Sensors NDTCalibration and repairs of all electrical electronic equipment 4. Reliability Record Tender has achieved the following reliability record, in the Middle East Area, from January 2006. A separate shall be given for each of the following equipment: Mud Motors Measuring While Drilling with Gamma Ray (Optional) Drilling Jar Stabilizers NMDC (Optional) HWDP Logging While Drilling (Optional) Gyroscopic Survey Tools Jar Accelerator Torque Reducer (Optional) RSS (Optional) Roller Reamer Shock Sub (Optional) Circulating Sub (Optional)5. New Technology Contractor shall itself and NIDC updated on the development of all new equipment and running procedures. 6. Tool Operating ParametersThe technical data are given in the following that shall be completed by contractor6.1 Down Hole Motor: for Directional Drilling and in case for performance Drilling6.1.1 for 23 1/2 Hole sizeDown hole Motors for 23 1/2 hole size aContractors DataUnitDescriptionItem11 1/4(inch)Nominal OD of motor19.82(m)Length: 2Y(Y/N)Surface adjustable 30-4(0)Deviation angle from tool axis414(0/30 m)Dogleg capabilities57(0/30 m)Max dogleg allowed for rotation67 5/8 REGTop connection type77 5/8 REGBottom connection type880,000(Lb.Ft)Max make-up torque91500(GPM) )Max flow rate10311.3(Psi)Pressure loss, max flow rate, .55sg111000(GPM)Minimum flow rate 1211597(15724N*M)(Lb.Ft)Torque at max flow rate13120(c)Max temperature 14655(Psi)Max differential pressure 1567.5(K.LB)Max WOB 1697/148/196(rpm)Min/Optimum/Max string RPM17677.3(Psi)Pres. loss at max flow rate, 1.55 sg (off btm)18196RpmMotor RPMs at max flow rate196.1.2 for 17 Hole sizeDown hole Motors for 17 hole sizebContractors DataUnitDescriptionItem9 5/8(inch)Nominal OD of motor 19(m)Length: 2Y(Y/N)Surface adjustable 30 or 1(0)Deviation angle from tool axis 414(0/30 m)Dogleg capabilities 57(0/30 m)Max dogleg allowed for rotation66 5/8 REGTop connection type 77 5/8 REGBottom connection type 851,000(Lb.Ft) Max make-up torque 91100(GPM) Max flow rate 1039.3(Psi)Pressure loss, max flow rate, .55sg11600(GPM)Minimum flow rate 1221460(Lb.Ft)Torque at max flow rate 13120(c)Max temperature 14934(Psi) Max differential pressure 157.92(K.LB)Max WOB 1672/102/132(rpm) Min/Optimum/Max string RPM17102.3(Psi)Pres. loss at max flow rate, 1.55 sg (off btm) 18132RpmMotor RPMs at max flow rate 196.1.3 for 12 1/4 Hole sizeDownhole Motors for 12 1/4 hole sizecContractors DataUnitDescriptionItem71/4(inch) Nominal OD of motor 19(m)Length: 2Y(Y/N)Surface adjustable 30-4(0)Deviation angle from tool axis414(0/30 m)Dogleg capabilities 57(0/30 m)Max dogleg allowed for rotation 64 1/2REGTop connection type 76 5/8 REGBottom connection type 851000(Lb.Ft) Max make-up torque9520(GPM) Max flow rate 10263.25(Psi) Pressure loss, max flow rate 45sg 11260(GPM) Minimum flow rate125779(Lb.Ft)Torque at max flow rate 13120(c)Max temperature 14824(Psi) Max differential pressure 1537.4(K.LB)Max WO 1691/136/182(rpm) Min/Optimum/Max string RPM17819(Psi)Pres. loss at max flow rate, 1.4sg (off btm) 18182Motor RPMs at max flow rate 196.1.4 for 8 1/2 Hole sizeDownhole Motors for 8 1/2 hole sizedContractors DataUnitDescriptionItem6 3/4(inch) Nominal OD of motor 19(m) Length: 2Y(Y/N)Surface adjustable 30-4(0)度Deviation angle from tool axis416(0/30 m)Dogleg capabilities 58(0/30 m)Max dogleg allowed for rotation64 1/2REGTop connection type 74 1/2REGBottom connection type 821000(Lb.Ft) Max make-up torque9237(GPM) Max flow rate 10559.2(Psi) Pressure loss, max flow rate, 1.2sg11119(GPM) Minimum flow rate 12997(Lb.Ft) Torque at max flow rate 13150(c)Max temperature 14466(Psi) Max differential pressure 1535.2(K.LB)Max WOB 16191/286/382(rpm) Min/Optimum/Max string RPM 17(Psi) Pres. loss at max flow rate, 1.2sg (off btm)18382Motor RPMs at max flow rate 19 6.2 MWD & GAMMA RAY: for Directional & Horizontal Drilling6.2.1 MWD & Gamma Ray for Hole size 23 1/2 Down hole Equipment MWD ToolaContractors DataUnitDescriptionItem 241.3 mmCollar, outside diameter, nominal1241.3 mmCollar, outside diameter, maximum276.2 mmCollar, inside diameter, average39.14/7.62mCollar, ength, max/min, m43064KgWeight with internal assembly57 5/8 REGTop connection, thread type680,000Top connection, make up torque, ( LB.FT )77 5/8 REGBottom connection, thread type880,000Bottom connection, make-up torque,(LB.FT)9Hot Dip Galvanizing bar steelCollar material type (for use with high KCI content in mud)10Maximum weight on bit, ( LB )11Maximum over pull , ( LB )12Maximum torque, with operation, ( LB )13Moment of inertia14Equivalent stiffness156Max dogleg, sliding, deg/30m163Max dogleg,rotating,deg/30m1715Max mudflow, with operation, GPM183Min mudflow, with operation, GPM1915Max mudflow, without operation, GPM20150Max temperature, with operation21180Max survival temperature, without operation2260KNMax pressure across tool, with operation23120Max rotary speed, with operation24100%Stabilization on tool2590%Stabilization on BHA26check valveSaver subs required27SpringPreferred pulsation dampener setting281%Max solids content in mud 291%Max sand content in mud 302mmMax particle size through tool 31Max conc./type LCM, with operation32Max conc./ type LCM, without operation3380 eyesSurface mud screen required34Down hole mud screen required3550-200PsiPressure drop through MWD tool with operation3620-100PsiBit Pressure drop for good date transmission3720Max H2S in mud, p.p.m38No limitationMax CO2 in mud, ppm39No limitationLimitations to mud type for tool operation40density no less