Documents WriteSN User Guide

WriteSNxxx User GuideWriteSN User GuideVersion: 1.0.1DocCode: Date: 2013-02-01Important NoticeCopyright NoticeCopyright 2013, Spreadtrum Communications, Inc. All rights reserved.TrademarksSpreadtrum Communications, Inc. and Spreadtrum Communications, Inc.s products are exclusively owned by Spreadtrum Communications, Inc. References to other companies and their products use trademarks owned by the respective companies and are for reference purpose only.Warranty DisclaimerSpreadtrum Communications, Inc. makes no representations or warranties, either expressed or implied, by or with respect to anything in this document, and shall not be liable for any implied warranties of merchantability or fitness for a particular purpose or for any indirect, special or consequential damages.ConfidentialityThe information contained herein (including any attachments) is confidential. The recipient hereby acknowledges the confidentiality of this document, and except for specific purposes, this document shall not be disclosed to any third party.About This DocumentPurposeThis document describes how to write SN , WIFI address and so on into phone.Intended AudienceThis document is intended for: l Installation and commissioning engineerl Technical support engineer OrganizationThis document consists of five chapters as follows.ChapterDescribesOverviewIntroduce function, runtime environment, and so on.Quick StartIntroduce basic operation of the tool.Operation GuideIntroduce detail operation of the tool.ConfigurationIntroduce some useful settings of the tool.FQASome useful answer and question.ConventionsSymbol ConventionsThe symbols that may be found in this document are defined as follows.SymbolDescriptionIndicates a hazard with a high level of risk that, if not avoided, will result in death or serious injury.Indicates a hazard with a medium or low level of risk which, if not avoided, could result in minor or moderate injury.Indicates a potentially hazardous situation that, if not avoided, could cause equipment damage, data loss, and performance degradation, or unexpected results.Indicates a tip that may help you solve a problem or save time.Provides additional information to emphasize or supplement important points of the main text.Frequently Used AbbreviationsAbbreviationDescriptionGUI ConventionsConventionDescriptionBoldfaceButtons, menus, parameters, tabs, windows, and dialog titles are in boldface. For example, click OK.Multi-level menus are in boldface and separated by the signs. For example, choose File Create Folder.Keyboard OperationFormatDescriptionKeyPress the key. For example, press Enter and press Tab.Key 1+Key 2Press the keys concurrently. For example, pressing Ctrl+Alt+A means the three keys should be pressed concurrently.Key 1, Key 2Press the keys in turn. For example, pressing Alt, A means the two keys should be pressed in turn.Mouse OperationActionDescriptionClickSelect and release the primary mouse button without moving the pointer.Double-clickPress the primary mouse button twice continuously and quickly without moving the pointer.DragPress and hold the primary mouse button and move the pointer to a certain position.ReferenceContents1 Overview2-11.1 Introduction2-21.2 Runtime environment2-21.2.1 Hardware2-21.2.2 Software2-22 Quick Start2-12.1 Main User Interface2-22.2 Quick Operation2-32.2.1 Step by Step2-33 Operation Guide3-13.1 Set3-24 Configuration4-14.1 WriteSN.ini4-25 FQA5-4Issue 01 (2013-02-01)Spreadtrum Communications Inc.5-5FiguresFigure 21 Main user interface2-2Figure 22 Setting dialog2-3Figure 23 Test result: PASS2-3Figure 25 Test result: FAIL2-4Figure 26 Test result: time out2-5Figure 31 Set Dialog3-3xxx User Guide5 FQA1 Overview1.1 IntroductionWriteSN is a tool that can be used to write SN and Bluetooth to the phone.WriteSN supports two modes to connect with phone, “Calibration Mode” and “Normal Mode”.Calibration Mode: Connected phone to PC with USB cable which V-BUS is disconnected, and then powered on it for test.Normal Mode: Powered on phone normally, and then connect to PC for test.1.2 Runtime environment1.2.1 Hardwaren A phone that needs to test.n A USB cable with V-BUS is disconnected (If you want to use “Calibration Mode”).n A normal USB cable (If you want to use “Normal Mode”).1.2.2 Softwaren Microsoft Windows 2000 or XP, Vista, Win7 or advanced operation system.2 Quick Start2.1 Main User InterfaceFigure 21 Main user interfaceThe major elements on the interface are described as follows:l 1. Port Select. If want to use “Calibration Mode”, then select USB. Otherwise, select COMX.l 2. Set Dialog. Some useful configuration can be set in this, please reference to 3.1 Set.l 3. Operation area. Write button is for writing SN/Bluetooth to the phone. Stop button is for stopping writing operation.l 4. Prompt for testing. All test information will be displayed is this area.l 5. Test items. These items can be set in the Set dialog. They are maybe generated automatically by default, or generated by inputting manually, or generated by scanner.2.2 Quick Operation2.2.1 Step by StepStep 1 Click “WriteSN.exe” to open the tool.Step 2 Click Set button to open setting dialog for some basic configuration.If you want to know more settings, please reference to 3.1 Set.Figure 22 Setting dialoglIf you want to use this tool to test WCDMA data card, then the switch mode without rebooting DUT (only for WCDMA data card) must be selected.Step 3 Select USB int Port.Step 4 Input, SN or bluetoothI, and then press Write button to write SN and other items to the phone.Step 5 Test finished.:Figure 23 Test result: PASSlIf you select Normal Mode, you must first power on the phone and connected it with PC, and then click Read or Write button to begin test.If you select Calibration Mode, you must first click Read or Write button, and then powered on the phone.-End3 Operation Guide3.1 Set Figure 31 Set Dialogl 1. PhaseCheck: Phase check or not. If you want to initialize product information, please check Initialize Product Info. (PhaseCheck).SN1: write SN1 or not. You can generated it automatically or by manually or by scanner.SN2: write SN2 or not. You can generated it automatically or by manually or by scanner.BlueTooth Address: write Blurtooth or not. You can generated it automatically or by manually or by scanner.l 2. Check the forepart of SN number by inputting in EDIT.l 3. If you want to use this tool to test WCDMA data card, then the switch mode without rebooting DUT (only for WCDMA data card) must be selected.l 4. Hardware Test. Click it and the dialog is shown as bellow:If Hardware Test is checked, the items of the “1” place will be enabled. Check the detail item that you want to test.l 5. Operation area.4 Configuration4.1 WriteSN.iniWriteSN.ini configures the common settings, such as UART port, instrument, cable lossetc. As most of the settings could be configured by UI directly, we only describe the useful items which should be configures by manually:GeneralTimeout=30000EntrerModeWait=3000WriteTimeCheck=0WriteTime=20000HardwareTest_PreWait=4000CheckStationName=CFTCurrentStationName=IMEITimeout: Specifies the wait time after DUT is under calibration mode. (Only available while calibration mode).EntrerModeWait: Wait time for enter mode.WriteTimeCheck: When write items