品质专业英语大全零件材料类的专有名词.doc

品质专业英语大全零件材料类的专有名词CPU: central processing unit(中央处理器)IC: Integrated circuit(集成电路)Memory IC: Memory Integrated circuit（记忆集成电路）RAM: Random Access Memory（随机存取存储器）DRAM: Dynamic Random Access Memory（动态随机存取存储器）SRAM: Staic Random Access Memory（静态随机存储器）ROM: Read-only Memory（只读存储器）EPROM:Electrical Programmable Read-only Memory（电可抹只读存诸器）EEPROM: Electrical Erasbale Programmable Read-only Memory（电可抹可编程只读存储器）CMOS: Complementary Metal-Oxide-Semiconductor（互补金属氧化物半导体）BIOS: Basic Input Output System（基本输入输出系统）Transistor：电晶体LED:发光二极体Resistor：电阻Variator：可变电阻Capacitor:电容Capacitor array：排容Diode：二极体Transistor：三极体Transformer：变压器（ADP）Oscillator：频率振荡器（0sc）Crystal：石英振荡器XTAL/OSC:振荡产生器（X）Relay：延时器Sensor：感应器Bead core：磁珠Filter:滤波器Flat Cable：排线Inductor：电感Buzzer：蜂鸣器Socket：插座Slot：插槽Fuse：熔断器Current：电流表Solder iron：电烙铁Magnifying glass：放大镜Caliper：游标卡尺Driver：螺丝起子Oven：烤箱TFT:液晶显示器Oscilloscope：示波器Connector：连接器PCB: printed circuit board（印刷电路板）PCBA: printed circuit board assembly（电路板成品）PP:并行接口HDD:硬盘FDD:软盘PSU: power supply unit（电源供应器）SPEC:规格Attach:附件Case: 机箱，盖子Cover：上盖Base：下盖Bezel：面板（panel）Bracket：支架，铁片Label ：贴纸Guide：手册Manual：手册，指南Card：网卡Switch：交换机Hub：集线器Router：路由器Sample：样品Gap：间隙Sponge：海绵Pallet：栈板Foam：保利龙Fiber：光纤Disk：磁盘片PROG:程序Barcode：条码System：系统System Barcode：系统条码M/B: mother board：主板CD-ROM:光驱FAN:风扇Cable：线材Audio：音效K/B: Keyboard（键盘）Mouse：鼠标Riser card：转接卡Card reader：读卡器Screw：螺丝Thermal pad：散热垫Heat sink：散热片Rubber：橡胶垫Rubber foot：脚垫Bag：袋子Washer：垫圈Sleeve：袖套Configuration：机构Label hi-pot：高压标签Firmware label：烧录标签Metal cover：金属盖子Plastic cover：塑胶盖子Tape for packing：包装带Bar code：条码Tray：托盘Collector ：集线夹Holder：固定器,L 铁Connecter：连接器IDE:集成电路设备，智能磁盘设备SCSI:小型计算机系统接口Gasket：导电泡棉AGP:加速图形接口PCI:周边组件扩展接口LAN:局域网USB:通用串形总线架构Slim：小型化COM:串型通讯端口LPT:打印口，并行口Power cord：电源线I/O:输入，输出Speaker：扬声器EPE:泡棉Carton：纸箱Button：按键，按钮Foot stand：脚架部门名称的专有名词QS: Quality system 品质系统CS: Customer Service 客户服务QC: Quality control 品质管理IQC: Incoming quality control 进料检验LQC: Line Quality Control 生产线品质控制IPQC: In process quality control 制程检验FQC: Final quality control 最终检验OQC: Outgoing quality control 出货检验QA: Quality assurance 品质保证SQA: Source(supplier) Quality Assurance 供应商品质保证(VQA)CQA：Customer Quality Assurance 客户质量保证PQA : Process Quality Assurance 制程品质保证QE: Quality engineer 品质工程CE: component engineering 零件工程EE: equipment engineering 设备工程ME: manufacturing engineering 制造工程TE: testing engineering 测试工程PE: Product Engineer 产品工程IE: Industrial engineer 工业工程ADM: Administration Department 行政部RMA:客户退回维修CSDI:检修PC: producing control 生管MC: master control 物管GAD: General Affairs Dept 总务部A/D: Accountant /Finance Dept 会计LAB: Laboratory 实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department 生产部PA:采购(PUR: Purchasing Dept)SMT: Surface mount technology 表面粘着技术MFG :Manufacturing 制造MIS: Management information system 资迅管理系统DCC: document control center 文件管制中心厂内作业中的专有名词QT: Quality target 品质目标QP: Quality policy 目标方针QI: Quality improvement 品质改善CRITICAL DEFECT:严重缺点（CR）MAJOR DEFECT: major defect主要缺点（MA）MINOR DEFECT: minor defect次要缺点（MI）MAX: Maximum 最大值MIN: Minimum 最小值DIA : Diameter 直径DIM : Dimension 尺寸LCL: Lower control limit 管制下限UCL: Upper control limit 管制上限EMI:电磁干扰ESD:静电防护EPA:静电保护区域ECN:工程变更ECO: Engineering change order 工程改动要求（客户）ECR:工程变更需求单CPI: Continuous Process Improvement 连续工序改善Compatibility：兼容性Marking：标记DWG: Drawing 图纸Standardization：标准化Consensus：一致Code：代码ZD: Zero defect 零缺陷Tolerance：公差Subject matter：主要事项Auditor：审核员BOM: Bill of material 物料清单Rework：重工ID：identification 识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR：First Piece Inspection Report 首件检查报告FAA:首件确认SPC：统计制程管制CP: capability index（准确度）CPK: capability index of process(制程能力)PMP:制程管理计划（生产管制计划）MPI:制程分析DAS : Defects Analysis System 缺陷分析系统PPB：十亿分之一Flux：助焊剂P/N:料号L/N：Lot Number 批号Version：版本Quantity：数量Valid date：有效日期MIL-STD：Military-Standard 军用标准ICT: In Circuit Test (线路测试)ATE：Automatic Test Equipment 自动测试设备MO: Manufacture Order 生产单T/U: Touch Up (锡面修补)I/N:手插件P/T:初测F/T: Function Test (功能测试-终测)ASSY : 组装P/K:包装TQM: Total quality control 全面品质管理MDA: manufacturing defect analysis 制程不良分析(ICT)RUN-IN:老化实验HI-pot：高压测试FMI：Frequency Modulation Inspect 高频测试DPPM: Defect Part Per Million(不良率的一种表达方式：百万分之一) 1000PPM 即为0.1%Corrective Action: (CAR 改善对策)ACC：允收REJ:拒收S/S：Sample size 抽样检验样本大小SI-SIV：Special I-Special IV 特殊抽样水平等级CON：Concession / Waive 特采ISO:国际标准化组织ISA：Industry Standard Architecture 工业标准体制结构OBA:开箱稽核FIFO:先进先出PDCA:管理循环Plan do check action 计划，执行，检查，总结WIP:在制品（半成品）S/O: Sales Order (业务订单)P/O: Purchase Order (采购订单)P/R: Purchase Request (请购单)AQL: acceptable quality level 允收品质水准LQL : Limiting quality level 最低品质水准QVL: qualified vendor list 合格供应商名册AVL ：认可的供货商清单(Approved Vendor List)QCD: Quality cost delivery（品质，交期，成本）MPM: Manufacturing project management 制造专案管理KPI: Key performance indicate 重要绩效指标MVT: Manufacturing Verification Test 制造验证试产Q/R/S：Quality/Reliability/Service 质量/可靠度/服务STL: ship to line（料到上线）NTF: No trouble found 误判CIP: capacity improvement plan（产能改善计划）MRB: material review board（物料审核小组）MRB: Material reject bill 退货单JIT: just in time（即时管理）5S:seiri seiton seiso seiketsu shitsuke（整理，整顿，清扫，清洁，修养）SOP: standard operation process（标准作业程序）SIP: Specification inspection process 制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction（作业指导书）SMD: surface mounting device（表面粘着原件）FAR: failure analysis report 故障分析报告CAR: Corrective action report 改善报告BPR： 企业流程再造 (Business Process Reengineering)ISAR ：首批样品认可(Initial Sample Approval Request)-JIT：实时管理 (Just In Time)QCC ：品管圈 (Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面品质环境管理)PD: Production Department (制造)LOG: Logistics (后勤支持)Shipping: (进出口)AOQ：Average Output Quality 平均出货质量AOQL：Average Output Quality Level 平均出货质量水平FMEA：failure model effectiveness analysis 失效模式分析CRB: Change Review Board (工程变更会议)CSA：Customer Simulate Analysis 客户模拟分析SQMS：Supplier Quality Management System 供应商品质管理系统QIT: Quality Improvement Team 品质改善小组QIP：Quality Improvement Plan 品质改善计划CIP：Continual Improvement Plan 持续改善计划M.Q.F.S: Material Quality Feedback Sheet (来料品质回馈单)SCAR: Supplier Corrective Action Report (供货商改善对策报告)8D Sheet: 8 Disciplines sheet ( 8D 单)PDCA：PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知)QAPS: Quality Assurance Process Sheet (品质工程表)DRP ：运销资源计划 (Distribution Resource Planning)DSS：决策支持系统 (Decision Support System)EC ：电子商务 (Electronic Commerce)EDI ：电子资料交换 (Electronic Data Interchange)EIS ：主管决策系统 (Executive Information System) ：企业资源规划 (Enterprise Resource Planning)FMS ：弹性制造系统 (Flexible Manufacture System)KM ：知识管理 (Knowledge Management)4L ：逐批订购法 (Lot-for-Lot)LTC ：最小总成本法 (Least Total Cost)LUC ：最小单位成本 (Least Unit Cost)MES ：制造执行系统 (Manufacturing Execution System)MPS ：主生产排程 (Master Production Schedule)MRP ：物料需求规划 (Material Requirement Planning)MRP：制造资源计划 (Manufacturing Resource Planning)OEM ：委托代工 (Original Equipment Manufacture)ODM ：委托设计与制造 (Original Design & Manufacture)OLAP：线上分析处理 (On-Line Analytical Processing)OLTP：线上交易处理 (On-Line Transaction Processing)OPT ：最佳生产技术 (Optimized Production Technology)PDCA：PDCA 管理循环 (Plan-Do-Check-Action)PDM：产品数据管理系统 (Product Data Management)RCCP：粗略产能规划 (Rough Cut Capacity Planning)SCM ：供应链管理 (Supply Chain Management)SFC ：现场控制 (Shop Floor Control)TOC：限制理论 (Theory of Constraints)TQC ：全面品质管制 (Total Quality Control)FYI/R: for your information/reference 仅供参考ASAP:尽快S/T: Standard time 标准时间TPM: total production maintenance：全面生产保养ESD Wrist strap：静电环IT: information technology 信息技术，资讯科学CEO：Chief Executive Officer 执行总裁COO：Chief Operating Officer 首席业务总裁SWOT：Strength, Weakness, Opportunity, Threat优势弱点机会威胁Competence：专业能力Communication：有效沟通Cooperation：统御融合Vibration Testing：振动测试IDP：Individual Development Plan 个人发展计划MRP：Material Requirement Planning 物料需求计划MATS：Material 材料LRR：Lot Reject Rate 批退率ATIN：Attention 知会3C：Computer ,Communication , Consumer electronic消费性电子5W1H：When , Where , Who , What , Why , Ho时间，地点，人物，干什么，为什么，？5M: Man , Machine , Material , Method , Measurement人,机器,材料,方法,测量4MIE: Man, Material, Machine, Method, Environment人力,物力,财务,技术,时间(资源)7M1I: Manpower , Machine , Material , Method, Market , Management , Money ,Information人力， 机器， 材料， 方法, 市场， 管理， 资金， 资讯1 Accuracy 准确度2 Action 行动3 Activity 活动4 Analysis Covariance 协方差分析5 Analysis of Variance 方差分析6 Approved 承认7 Attribute 计数值8 Average 平均数9 Balance sheet 资产负债对照表10 Binomial 二项分配11 Brainstorming Techniques 脑力风暴法12 Cause and Effect Matrix 因果图(鱼骨图)13 CL: Center Line 中心线14 Check Sheets 检查表15 Complaint 投诉16 Conformity 合格（符合）17 Control 控制18 Control chart 控制(管制)图19 Correction 纠正20 Correlation Methods 相关分析法21 CPI: continuous Process Improvement 连续工序改善22 Cross Tabulation Tables 交叉表23 CS: Customer Service 客（户）服（务）中心24 DSA: Defects Analysis System 缺陷分析系统25 Data 数据Description:品名26 DCC: Document Control Center 文控中心27 Decision 决策、判定28 Defects per unit 单位缺点数29 Description 描述30 Device 装置31 Do 执行32 DOE: Design of Experiments 实验设计33 Element 元素34 Engineering technology 工程技35 Environmental 环境36 Equipment 设备37 Estimated accumulative frequency 计算估计累计数38 EV Equipment Variation 设备变异39 External Failure 外部失效,外部缺陷40 FA: Failure Analysis 失效分析41 Fact control 事实管理42 Fatigue 疲劳43 FMEA: Failure Mode and Effect Analysis 失效模式与效果分析44 FPY : First-Pass Yield （第一次通过）合格率45 FQA: Final Quality Assurance 最终品质保证46 FQC: Final Quality control 最终品质控制47 Gauge system 测量系统48 Grade 等级49 Histogram 直方图50 Improvement 改善51 Initial review 先期审查52 Inspection 检验53 Internal Failure 内部失效、内部缺陷54 IPQC: In Process Quality Control 制程品质控制55 IQC: Incoming Quality Control 来料品质控制56 IS International Organization for Standardization 国际标准化组织57 LCL: Lower Control limit 管制下限58 LQC: Line Quality Control 生产线品质控制59 LSL: Lower Size Limit 规格下限60 Machine 机械61 Manage 管理62 Materials 物料63 Measurement 测量64 Median 中位数65 MSA: Measurement System Analysis 测量系统分析66 Occurrence 发生率67 Operation Instruction 作业指导书68 Organization 组织69 Pareto 柏拉图70 PPM : Parts per Million （百万分之）不良率71 Plan 计划72 Policy 方针73 Population 群体74 PQA: Process Quality Assurance 制程品质保证75 Practice 实务(践)76 Prevention 预防77 Probability 机率78 Probability density function 机率密度函数79 Procedure 流程80 Process 过程81 Process capability analysis 制程能力分析（图）82 Process control and Process capability 制程管制与制程能力83 Product 产品84 Production 生产85 Projects 项目86 QA: Quality Assurance 品质保证87 QC: Quality Control 品质控制88 QE: Quality Engineering 品质工程89 QFD: Quality Function Design 品质机能展开(法)90 Quality 质量91 Quality manual 品质手册92 Quality policy 品质政策(质量方针)93 Random experiment 随机试验94 Random numbers 随机数95 R: Range 全距（极差）96 Reject 拒收97 Repair 返修98 Repeatability 再现性99 Reproducibility 再生性100 Requirement 要求101 Responsibilities 职责102 Review 评审103 Reword 返工104 Rolled yield 直通率105 RPN: Risk Priority Number 风险系数106 Sample 抽样,样本107 Sample space 样本空间108 Sampling with replacement 放回抽样109 Sampling without replacement 不放回抽样110 Scatter diagram 散布图分析111 Scrap 报废112 Simple random sampling 简单随机取样113 Size 规格114 SL: Size Line 规格中心线115 Stratified random sampling 分层随机抽样116 SOP: Standard Operation Procedure 标准作业书117 SPC: Statistical Process Control 统计制程管制118 Specification 规范119 SQA: Source(Supplier) Quality Assurance 供货商品质保证120 Stage sampling 分段随机抽样121 Standard Deviation 标准差122 Sum of squares 平方和123 Taguchi-method 田口(试验)方法124 Theory 原理125 TQC: Total Quality Control 全面品质控制126 TQM: Total Quality Management 全面品质管理127 Traceability 追溯128 Training 培训129 UCL: Upper Control Limit 管制（控制）上限130 USL: Upper Size Limit 规格上限131 Validation 确认132 Variable 计量值133 Verification 验证134 Version 版本135 VOC: Voice of Customer 客户需求136 VOE: Voice of Engineer 工程需求137 Inventory stock report:庫存清单报告138 Sales order report:出货报告质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商质量评估FMEA failure model effectiveness analysis 失效模式分析FQC 运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 质量/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproducibility & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它质量术语类QIT Quality Improvement Team 质量改善小组ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准CGOO China General PCE 龙华厂文件IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 资料中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASSY Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WDR Weekly Delivery Requirement 周出货要求PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 发光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessAVL Approved vendor list通用类president 董事长operator 作业员position 职务general manager 总经理special assistant 特助deputy manager |depjuti| =vice manager 副理deputy supervisor =vice supervisor 副课长group leader 组长line leader 线长supervisor 课长responsible department 负责单位Human Resources Department人力资源部Head count 人头数production department 生产部门planning department 企划部QC Section 品管课stamping factory 冲压厂painting factory 烤漆厂molding factory 成型厂administration/general affairs dept./总务部production unit 生产单位meeting minutes 会议记录distribution department 分发单位subject 主题conclusion 结论decision items 决议事项pre-fixed finishing date 预定完成日Color management 颜色管理Visual management 目视管理production capacity 生产力first count 初盘first check 初盘复棹second count 复盘second check 复盘复核quantity of physical inventory second count 复盘点数量physical inventory 盘点数量physical count quantity 账面数量difference quantity 差异量spare parts physical inventory list 备品盘点清单cause analysis 原因分析waste materials 废料description 品名specification 规格model 机种work order 工令revision 版次remark 备注registration 登记registration card 登记卡to control 管制appl