英汉日模具用语大辞典.docx

英汉日模具用语集uz英语汉语日语U flexure diesU型弯曲模U)U字形曲型U-bendingU形弯曲U曲UF urea resin尿素树脂)尿素樹脂ultimate strength极限强度)極限強ultraprecision processing超精度加工)超仕上ultrasonic carver超声波加工机)超音波加工機ultrasonic cleaning超声波清洗)超音波洗浄ultrasonic machine超声波加工机床)超音波加工機ultrasonic weld超声波溶接)超音波溶接ultra-sophisticated moldings超精密成形品)超精密成型品un loader取出装置unanimous一致）合uncoiler开卷送料机under annealing不完全退火under cut横抽芯脱模部位under cut型腔脱模凹处倒扣under cut milling清角铣刀under cut to process横抽芯处理処理(undercooling state过冷却状态)過冷却状態under-part drive pattern下部驱动模式undertake从事）持undertaking事业）事業under-writers LaboratoryUL规格UL規格(unfilling未填充)未充unflappability不慌张）慌unilateral datum joiners gauge单侧基准划线规)片unit capacity weight单位容积重量)単位容積重unit mold工序模unit mold单工序模unit number组合序Unit of measure计量单位UOMunit price to process加工单价)加工単价unitizing to exchange die凸模成组互换模金型universal die组合冲模)万能universal machine通用设备)汎用機universal milling machine万能铣)万能盤universal mold通用模)普遍型universal old通用模具universal tool grinding万能工具磨床)万能工具研削盤universal tool grinding machine万能工具磨床)万能工具研削盤universal vice万能老虎钳）万能universaljoint万向节unlike material shear strength不同材质的剪切强度)材質別剪断抵抗unloader carrier卸料装置动作unloading device出件装置)取出機Unofficial notification order内部定单)内示unscrewing mold螺纹嵌件模 抜型unworked casting不再加工铸件)鋳放up向上up and down at the same time to press way上下同时压方式)両押方式UP dope不饱和聚酯涂料)不飽和樹脂塗料up empty out state向上腾空状态)浮上状態UP unsaturated polyester resin非饱和聚酯树脂)不飽和樹脂Upgrade升级upper bolster上模座）上型upper die上模)上型upper shor、上模座）上型upright立柱upright drilling machine立钻)直立盤upset forging machine镦锻机機upsetter镦锻机upsetter镦锻Upsetting自由锻)自由据込()upsetting镦粗加工)据加工upsetting镦粗込（upsetting镦粗込作業upsetting die镦锻模型upsetting rivetter镦粗铆接upward view仰视图)下面図upwards向上）向上Use of every day每天使用的)日活用user用户user用户User Interface用户界面user pleased用户满意质量工程)後向品貭user pleased用户满意）顧客満足Users manual用户手册utensil hematology检验用具)検査用機器utensil jostle皿型推挤)皿utensil pin皿形销)皿V flexure dieV型弯曲模V)V曲型V jigV形夹具（轴类VV Process decompression molding casing减压造型铸造法V鋳造法(V、L flexual to unfoldV、L弯曲的展开VL曲展開(vacuum carbonitriding渗碳氮化)真空浸炭窒化vacuum carburizing渗碳)真空浸炭vacuum drier真空干燥机)真空乾燥機vacuum evaporation真空蒸镀)真空蒸着vacuum hardening真空淬火)真空焼入vacuum heat treatment真空热处理)真空熱処理vacuum physics electroplate真空物理电镀TiCvaenish清漆Validation Switch function确认开关功能機能value价值value价值)価値value-added rates附加价值率)付加価値率valve阀valve pressure活塞压圧(VAM vinyl acetate醋酸盐)酢酸vanadium钒(V)variable clamping plate动模侧安装模板）可変定盤variable transformer可变变压器variable voltage regulator变压器)可変電圧調整器Variation变化Variation reduction偏差缩减variety leave ratio品种别比例)品種別比率various containers各种容器)各種Various numbers of commands各种指令数)各種数Various products多种多样产品)多種多様製品V-bendingV弯曲V曲V-blockV形块规VVCM vinyl chloride monomer氯乙烯单体)塩化vehicle运输工具velocity of flow流速)流速vent拉深排气孔ventical machine center立式加工中心)立形verify sensor request and not确认传感器要否)確認要否vernier caliper游标卡尺M形vernier graduation data游标刻度数据vertical垂直)垂直vertical compression type直压式)直圧式vertical drill立钻)直立盤vertical equipment立式设备)立型機vertical grinder立磨vertical injection machine立式注塑机)竪型射出成形機vertical lathe立式车床)立旋盤vertical load to morph deformation temperuu垂直负重变形温度)荷重温度vertical milling machine立铣)立盤vertical nodulus of elasticity纵弹性率率（vertical projecting plane垂直投影面)垂直投影面vertical type vice立式老虎钳)立万力verticalcompression matched molds直压式合模机构)直圧式型締機構vesicant发泡剂)発泡剤vestige痕迹vestigital internal stress shaped成形残留变形)成形残留vibrating body action振动体作用)振動体作用vibrating feeder振动送料机vibration few振动少)振動少vibration to resolve振动解析)振動解析vibrin聚酯树脂樹脂vice老虎钳vice台式老虎钳)横万力vice jaw spacing老虎钳钳口垫片）口金vice president副社长、副总经理）副社長vigorous旺盛)旺盛vinyl tapped steel sheet塑胶覆面钢板鋼板virgin原始的virtual shearing force设计剪断力剪)仮想剪断力virtual travel空行程)空打virus病毒viscosity粘度)粘度vision视觉visualization可视化)見化visurl inspection外观检查）外観検査vitrified陶瓷VMI Vendor Managed Inventory供应商管理库存主導型店舗在庫管理voic content空洞率)空洞率void焊接空隙volume contraction体积收缩)体積収縮Volume of data数据量量volume of trial shot goods试注射件体积品体積volume-produce大批量生产冲床)量産voluntary liquidation自动清理)自動v-ring齿圈（精冲模）板押V突起wages工资)給料waling纵向加强筋wall thickness off-the-shelf成形品的壁厚)成形品肉厚wall thickness products厚壁制品)厚肉製品warm pressing常温压机)温間warp翘曲warp翘曲warp翘曲(warp翘曲)曲warpage翘曲、)反warpage矫曲warpage test翘曲试验試験warped弯曲)反washer垫片washer垫圈washer垫圈waster损耗watch dog frame监视器画面画面water absorbing capacity吸水率)吸水率water channel冷却）水路）水路water jet machine高压液体研磨机加工機(water pipe inside diameter水管内径)水路内径Water temperature and water pipe tie up水温与水管拴）水温水道栓water temperature control水温调节装置)温水調節装置water temperature sensor温度感应器)温度waviness波痕waviness波痕)波waving. phenomenon波浪现象)波打現象wax pouring mould失蜡浇注用模具鋳造用金型W-bendingW弯曲W曲WBS Work Breakdown Structure工作分解结构)仕事破壊構造wear磨损）摩耗wear and tear磨损)摩耗状況wear resistance耐磨性)耐磨耗性weather fastness耐气候性)耐候性weather fastness modifier耐气候性改质剂)耐候性改質剤wedding agent结合剂)結合剤wedge斜锲weight重量weight荷重)荷重weld焊接weld line注塑件冷隔线weld mark溶接痕welding溶接）溶接welding distontion焊接变形)溶接welding flux焊剂welding jig焊接工夹具)溶接治工具welding part augmentation熔结部分增大)溶着部分増大welding strain焊接应变）溶接歪well type nozzle单位组合电子元件wetmilling湿磨)湿式研削wetout浸润处理wharf码头)波止場wheel轮when demould become deformed脱模时的变形)離型際変形When upgrading corresponding exchange function升级时对应互换功能)外部機能When you use off-the-shelf parts completely使用在库品的变更)在庫部品使切whire cast iron白口铸铁鋳物whirl vessel processing从平板旋转容器加工加工white-collar family白领阶层族(white-collar worker公司职员）会社員whitening白化)白化whole die cavity kellering整体型腔仿形铣whole heat insulation nozzle完全隔热喷嘴)完全断熱whole injection pressure整个射出压力）全射出圧力whole injection time整个射出时间）全射出時間wide scope广范围)広範囲wide,long and high长宽高)厚()幅()長()width of rib加强筋宽幅wipe grinding消除磨削烧焦wipe off eyewinker on billot条料上异物去除)材料上面異物排除wipe off mixing gaseous way去除混炼产生气体的方式式wiper脱模钳wire cut线切割wire E.D.M线切割机床放電加工機wire electric discharge machine线切割机床放電加工機wire rope钢丝绳wiring卷缘wiring拉丝加工wiring芯棒卷缩加工wiring press卷边机within contract with境内承包）構内請負woem and gear蜗轮蜗杆wood木材)木材wooden model木制模特)木製原形wooden odel木模型)木型woodworker tooth木工齿（锉刀）)鬼目word processer字处理软件加工者words ang deeds言行）言動wore-electrode cutting correction线切割修正量補正量wore-electrode cutting finish surface线切割加工面放電加工面work工作）働work加工件Work Center工作区)作業区Work center priority level优先级工作中心優先順位work in process半成品)仕掛品Work package工作包work sheet加工单)作業指示票work standards作业标准)作業標準work to process加工物)加工物work transfor工件夹持送料Worker load操作人员负荷)要員負荷workhardening加工硬化)加工硬化working accuracy加工精度)加工精度working allowance加工余量)加工代working capability工作能力)仕事能力working density加工密度)加工密度working dimensional drawing铣加工尺寸图)彫込寸法図working drawing工作图)工作図working energy工作量)仕事量working fluid加工液)加工液working management工程管理)工程管理working management system工程管理系统)工程管理working place加工场所)加工箇所working procedure category工序类别名(working stress允许应力)許容応力working time to raise增加加工工时)製作工数増working to copy拷贝加工)転写加工workpiece advancing坯件推进送料送(workpiece datum plane localization method工件基准面定位法)現物合方法workpiece forwarding工件运送送料搬送(workpiece geometry工件外形形状(workpiece guide way工件导向槽workpiece transfer within a press压机内夹持送料内部品搬送(worktable size床身工作台尺寸寸法worst最坏、最差wortle plate拉丝模板wortle plate拉丝模板板wrench螺旋扳手ydroscopic property吸湿性)吸湿性Yield产量、收益)歩留yoke type die颈圈模型yoke type die轭型模金型youngling新手)未熟練者Z pinZ钉ZZ-bendingZ弯曲Z曲（）zero零zero draft pin无锥度型芯zinc stearate硬脂酸锌酸亜鉛(Zone melting method淬火法法Zoom function缩放功能機能英汉日模具用语集s中shell castiron壳模铸造鋳造shell mold casting热硬化壳型铸造型鋳造Shell Mold Process casting 热固性壳模铸造法鋳造法sheradizing渗锌法Shift备注shift偏移shim分隔片（冷却水shim block垫片shipment by unit constituent装船出货)単体出荷shipper货主)荷主shipping装船)船積shipping manifest specification装船仓单)出荷納入仕様書shipping mark唛头)荷印shippment 出货)出荷shock冲击shock line成形工序啮合拉伤shoe模座上下模板shoot填充压力)充填圧力shoot槽Shop order制造指令单)製造指図short短的Short delivery短交货期)短納期short fiber短纤维)短繊維short shot充填不足)充填不良short shot 充填不足）充填不足short shot 一次注塑量不足Shortcut key customizing快捷键定制shot单工序注射shot一行程完成的工作shot blast喷砂处理shot blasting喷丸处理shot capacity注塑容量)射出容量shot cycle注射周期shot peen喷射头 shot peening喷丸加工shot pin注射头shot time 注射时间shoulder担负、承担)担shoulder bolt有肩螺栓shoulder glade to defend pull out防拔出肩胛)抜止show process过程显示Show Process显示过程shrink收缩）収縮shrink缩水、缩凹shrink error收缩差）収縮差shrink fit红套紧固配合)焼嵌shrink fit红套)焼shrink fixture margin example收缩紧固余量实例)締実例shrink flange压缩凸缘）縮Shrink inhomogeneity收缩不均一）収縮不均一shrink mark缩陷现象shrink mark缩凹（)shrink space收縮余地、收縮公差）収縮shrinkage烧结收缩)焼結縮shrinkage不合格率)不良率shrinkage hole缩孔shrinkage pool收缩凹陷shrinking allowance重合反应)重合反応shut height吊环、shut height闭合高度shut height冲床最大闭合高度shutter百叶窗)鎧戸shuttle feeder夹持送料SI unitSI单位SI単位(side compression equipment侧压装置)側部圧力装置side core 横抽芯镶块side core coil spring横抽芯弹簧side core spring 横抽芯弹力side core type 横抽芯形式side cutting pliers扁钳side direction to spout working fluid侧向喷加工液法)工作物側噴流方法side elevation侧视图)側面図side gate横浇口side letter补充条款)補足文書side milling边铣)側削side wall thickness to count模腔侧壁厚度的计算)側壁厚計算signal bronze铜锡合金)銅合金signal transducer模拟量数字电气信号传感器signed at签订地点)打合場所silastic硅橡胶silastic滚筒炼胶的聚合橡胶、硅橡胶silastic stripper pad硅橡胶脱料法silica gel硅胶silicon硅silicon carbide碳化物 )炭化素silicon dioxide二氧化硅)二酸化素silicon steel sheet矽钢片)珪素鋼板silicone resin硅树脂)珪素樹脂silicone rubber硅橡胶silk丝silk screen钢丝筛silver 料花Silver paint银粉漆）銀Silver streak银色条纹silver tunqsten银钨)銀(AgW)silvery white striation流动方向银白条痕)銀条simple 3D object 简单立体形状)簡易立体形状Simple appraised简便的股价)簡易見績simple quality control易质量管理)品質管理容易simple stamping mold简易冲压模)簡易抜型Simple time of delivery imputed 简易的交货期估算)簡易納期算出simulation斑点simulation模拟仿真simulation model模拟模式simultaneous control of axles同时控制轴数)同時制御軸数Simultaneous fill同时填充)同時充simultaneous pressing同步冲压)同時押()sine baf正弦量规single单、一个single action单动single action单动)単動single cavity mold单腔模具)一個取金型single cavity mold单腔模)単数取型single crystals sandstone单结晶砂轮)単結晶砥石single die单道模）単発型single procedures单过程段取single spindle automatic lathe单轴自动车床)単軸自動旋盤single station special purpose machine单工位专用设备専用工作機械single stroke单冲程single system1系统)1系統single thread单头螺纹)一条single to drive 单一驱动駆動single to produce单个生产)個別生産single-action crank press单动曲轴压力机)単動single-action hydraulic press单动液压压力机)単動液圧single-candidate proportion yearly每年等额分摊)毎年期等額払single-crank press单曲轴压力机1)1点single-crank press曲轴冲床single-crank press单曲轴压力机single-minded function equipment专一功能设备)単能機single-operation die单工序模)単発型single-side relief sculpture单面浮雕模)片面型sink mark缩痕sinking下凹)凹sinter forging烧结铸造鍛造sintered compact烧结体)焼結体sintered density烧结密度)焼結密度sintered friction material烧结摩擦材料)焼結摩擦材料sintering烧结)焼結sintering烧结加工sinterring巡回检查)巡回検査sinzing die整形模型sinzing press精整压力机sit pad座籿垫）座site number 站点数数Situation of hot water surroundings热流料环境)湯廻状況size伺服电机驱动射出成形机駆動式射出成形機size 尺寸size exceptional尺寸异常)寸法異常size franchise尺寸允差)寸法許容差size marking way尺寸标注法)寸法記入法size meet requirement达到要求尺寸)寸法出（）size position尺寸位置)寸法位置size to assist mark尺寸辅助记号)寸法補助記号sizing胶料sizing螺旋料筒前端溶融量)残量sizing冲压特定厚度)寸法決作業sizing整形）整形skeleton框架skeleton drawing结构图)構造線図sketch drawing简图)見取図skid刹车、滑动skill熟练、有技艺Skill table技能表表(skin check细裂痕)微skin inclusion表面夹杂物)表皮引込skin miller表皮铣床skive研磨、校平skive traverse table研磨小平板)擦合定盤skiving表面研磨slab miller大型平面铣床slab thickness not revision die板厚无需调整的模具)板厚無調整式金型slack quench differentiate调质区分)調質区分slack quenching不完全淬火slag riser冒渣口押湯(slant face斜面)斜面sleeve套筒sleeve 二板式成型模金型sleeve ejection pin套筒顶出突出sleeve pin套筒销sleeve plate type套筒板式slew rate转换速度slicing machine钢锭切分机slidacs可变变压器slide滑块slide adjusting screw滑块调整螺丝調整slide block滑块slide core横抽芯滑块Slide Core Pins横抽芯滑块销slide driver element滑块驱动单元駆動slide furrow滑槽slide holder滑块座slide mode by ball bearing滚珠滑动方式方式slide part滑动部) 摺動部slide rod setting滑块调整量調節量slide rod to drive滑块驱动駆動slide Rods倾斜滑块杆slide stroke滑块冲程slide Unit滑块结构slider滑块slider滑子、滑块sliding pinion type滑动小齿轮式)摺動式slight engrave纤细的雕刻)繊細彫刻slip agent助滑剂剤slip joint滑配接头継手(slippage part to prevent sinter滑动部的防止烧结)摺動部焼付防止slit窄缝slit mold凹模拼块结构）割型slitting割缝加工)切込加工slitting切缝量込)切込量slitting割缝加工（切込）加工slitting 套筒推料杆突出（slogan标语、广告slope sculpture type倾斜纹饰种类slot长方形孔)狭槽 slot chisels窄口凿slot width槽宽 ）溝幅slotting冲槽slotting插床加工加工slotting切缝切削)立削slotting machine插床slotting machine立式刨床)立削盤slow cooling缓冷slow cooling慢冷)徐冷slow down减速slug废料slug disposing冲压废料处理処理slug hole落料孔slurry浆料slush molding中空成型)中空成形slushing oil防锈油)防錆油SM styrene monomer苯乙烯 small screw小螺杆Ssmall size exact die小型精密模具)小形精密型small-bore小孔径冲孔)小径穴抜smap gauge卡规SMC compression forming热固性强化纤维板材压缩成形SMC成形(smithing die冲压锻造模具鍛造用型smooth润滑)潤滑smooth光滑的，平滑的smooth cut油光锉)油目smooth-edge blanking光洁冲裁）仕上打smriti传承）伝承snap ring groove止动环槽)輪溝snap-on直接固定)直締SOA service oriented architecture服务导向架构適応soaking均热处理social effect社会效益）甲斐society contribution社会贡献）社会貢献Society Plastics Indastry美国塑料工业协会SPIsociety son社会一员）社会人socker head screw内六角螺钉)六角穴付socle beam悬臂梁)片持s