船舶符号缩写

aAbove base line A/B基线上方Access hole ACC .HOLE通道端口添加Additional ADD，添加After perpendicular A.P尾部垂直线Afterward AFT朝船尾After peak tank A.P.TK尾舱气穴a/h气口，通风孔Alignment ALIGNMENT调整，对齐Arrangement aarr t阵列Assembly ASSY装配，装配bBallast water tank B.W.T压载水舱基本线B/L基准线Bead BEAD焊肉光束Bilge keel BLG KEEL小屋龙骨比尔兹韦尔b/w下水道Block BLK(B)段Block division BLK。拆分DIV段Bottom BTM地板Bracket BKT加强板Bulb plate B.PL，B.P球型钢Bulkhead BHD旁边，舱壁Bulwark BULWARK船的扶手、防波堤Buttock line B.L垂直剖面线Butt welding BUTT WELDING对接缝焊接c起拱起拱kago hold c/h货舱刀剑 g部分加强板铸造CASTG铸铁中心线C/L中心线链摇臂链lkr链库链管链管链管切角C倒角Channel C.H通道鼻子aming coam g填充线面板，通过零件Check plate C.PL图案钢板Cofferdam C/D cofferdam，防油堰Collar plate C.PL修补程序Component assembly COMP。ASSY小型组件构造Construction CONST结构Corrugated bulkhead CORR.BHD波形舱壁裂缝破裂，裂缝Corrosion腐蚀曲线弧切割切割切割到G切割dDeck DK平台Deck house DK HOUSE船室Detail DET详细信息Diameter DIA直径Diaphragm DIAFH水平分区Double bottom D.BTM双层地板Double continuous fillet D.C.F双面连续焊接Double plate D.PL双层Drain hole D/H出水口eEach EA计数，全部Elevation EIEV侧视图机房e/r机舱Engine room bulkhead E/R BHD机车室墙Equal angle E.A等边角度关闭Erection EREC扩展Expansion EXPAN扩展，扩展fFabrication sequence diagram f.s.d组件程序图False bottom FALSE BTM作业/假地板Fashion plate FASHION PL组态船第一材料挡泥板，挡泥板扁条F. b扁铁Face flat F/F面材料，面板Floor F楼板Fore peak tank F.P.TK第一个尖形小屋Fore perpendicular F.P第一条垂直线Forecastle deck F到CLE DK第一层甲板向Forward FWD船头Foundation FDN基础框架fr肋骨，骨骼Frame space F.S肋骨间距Fresh water tank F.W.TK淡水舱Fresh water generator海水淡化设备全熔解焊接F.P完全熔焊Fillet joint材质相交Flange火腿Funnel FUNNEL烟囱。年份gGalvanized GALV镀锌、电镀General arrangement G/A常规布局Girder GIR船舶末端和末端方向的主纵梁Girnding GIRNDG研磨，受挫Gutter bar GUTTER BAR排水挡板hH-梁h-梁h-钢，I-梁Half round bar H.R.B半圆钢Hand grip H/G手柄Hatch图案填充Hawse管道hawse管道链管道霍尔德霍尔德船舱孔孔霍珀坦霍夫。tk碰撞舱Horizontal HORL水平II-beam I-BEAM I型钢Insert plate INSERT PL嵌入式主板检查Inspection INSP反转角度I.A逆角度kKnuckle line K.L折弯线关键计划主平面Knuckle point K.P转折点lLifting beam LIFTG BEAM吊装梁lifting LUG LIFT G LUG LUG rug发光孔L/H减肥孔Longitudinal bhd LONGL。BHD垂直分区Longitudinal space L.S垂直间距鲁格布线look g观测方法mMain deck MAIN DK主甲板检修孔m/h检修孔Man hole cover M/H COVER检修孔盖马克马克马克最大最大值Midship MIDSHIP船体中部Minimum MIN最小值Mould line ML理论行nNavigation bridge deck NAV。BRI.DK航海甲板编号否编号No water tight bulkhead N.W.T.BHD非水密舱壁oOffset OFFSET偏移Opening OPEN到G洞口Only ONLY，单独Outfitting OUTFITTG艏ppad plate pad . pl padPartial penetration welding P.P部分焊透焊接Perforated flat PERF。FLAT多孔管支柱支柱(P)柱Pipe hole P/H管孔计划计划计划，计划Steel plate PL钢板平台deck PLATE DK平台平台层面板Poop deck P.DK船尾拥抱甲板左舷合并Pre-erection P.E词典Q /RQuality control Q.C质量管理、Radius R半径Radius end R.E半径端Round bar R.B圆钢Rudder trunk R/T方向舵s缩放Scale SSea chest S/C海水进气口Section SEC剖面侧壳s .壳侧舱Snip拔模速度日志速度测量仪Square bar S.B方形钢Starboard STBD右舷Stay STAY柱Steering gear S/G伺服系统步进ST选项卡Stern frame S/FR船尾骨料Stiffener STIFF加强板Stringer STR船侧纵筋Sub-assembly SUB ASS至Y团队支架Swage bulkhead SW BHD槽壁tTack welding T.W位置焊接，点焊罐子，容器Tank top T/TOP小屋顶部Temporary TEMP临时Thickness THK，t厚度Transverse TRANSV水平Transverse bulkhead TRANSV。BHD横向隔壁三叉戟反英肘Typical TYP典型uUnequal angle U.A不等边角度Upper deck UPP。在DK上甲板vVoyage航海垂直VERT垂直V