WOHA33_3509139_284_AT-052450-200-809R

Hong Kong Airlines Limited香港航空有限公司03110-01Hong Kong Airlines MEDHong Kong Airlines LimitedWO NO/工作指令号SEQ NO/序列号WOHA333509_284_139培训方式3509139通用类/GenericTitleGENERAL VISUAL INSPECTION OF LOWER AND REAR PYLON FAIRINGS - RIGHT ENGINEMcd&Rev/厂家工卡&修订日期标题整体目视检查下部和后部发动机吊架整流罩-右发AMM 05-24-50-200-809 2017-07-01A/C/飞机号Subtask No/工卡号JC Rev/工卡版本号Workarea/工作区域Skill/工种Man Hour/工时BLNZAT-052450-200-809RHR001000动力/PowerplantAIRP00:24MP Item/MP号Baseline/依据MP REV/ MP版本号Station/维修站Threshold/首检Interval/重复检HA33-ZL-454-05-2MPDZL-454-05-2,MRBZL-454-05-2Issue 2 Revision 6PVG1275 CA1275 CAAccess Panels/接近盖板Zones/区域Written/编写Approved/批准454BL 454BR 454CL 454GL 454HL 454JL 454KL 454ML 454NR 464BL 464BR 464CL 464GL 464HL 464JL 464KL 464ML 464NR454 4642017-09-282017-09-29TOOLS/工具TOOLS NECESSARY/必须工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注TOOLS IF NECESSARY/视情工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIAL/航材NOTE:OPERATOR MUST GET AND INSTALL THE PARTS THAT CORRESPOND TO THE RELATIVE WORKORDER NO.注释：请工作者严格按照工作指令号领取预定的航材装机PARTS AND MATERIAL NECESSARY/必须航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIALIF NECESSARY/视情航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注1F5453082320200SEALAS4ALL(视情/As Necessary)refer to IPC when replace/更换时以IPC为准IMPORTANT NOTE:In the event of any discrepancies between the Chinese instruction and the English instruction, the English procedure should prevail.Record Additional Work/Findings(If Applicable) Reference No. Certificate of Release to Service (* Tick as appropriate # Different crews should perform the work on each of the systems)Certifies that the work specified, except as otherwise specified, was carried out in accordance with HKAR-145and in respect to that work, The aircraft / aircraft components are considered ready for Release to Service. HKA Approval No: AI / 135 / 706 * HKE Approval No: AI /218/1215, JMM 133 * HNAT Approval No.: D.101115, JMM 047* CASL Approval No: AI / 101 / 798 * AMECO Approval No.: D.101131, JMM 001* HNAT- North West Approval No.: D.500023, JMM 049 * HAECO Approval No: DAI / 1 / 853 * SMECO Approval No.: D.400009, JMM 081* HNAT- YN Approval No.: D.4108, JMM 134 * TAECO Approval No.: DAI / 89 / 1295 * CEA Approval No.: D.200002, JMM 112 * HNAT Approval No.: D.3039, JMM 076 * THAECO Approval No.: D.101661, JMM 124 * CEA-Jiangsu Approval No.: D.200047, JMM 117 * SPRING Approval No.: D.200081, JMM 121 * SIAEC Approval No: AWI / 01 * STARCO Approval No.: D.200078,JMM 039* GAMECO Approval No.: D.300001, JMM 006* THAI Approval No.: AI / 147 / 0910 * Other: *Signature:_ Authorization No.:_ Date:_AT-052450-200-809R HR001000 W/O:3509 AC:BLNZ页码，2 / 10工卡Job card:HA33-ZL-454-05-2TITLEGENERAL VISUAL INSPECTION OF LOWER AND REAR PYLON FAIRINGS - RIGHT ENGINEPerfInsp标题整体目视检查下部和后部发动机吊架整流罩-右发工作者检查者GENERAL VISUAL INSPECTION OF LOWER AND REAR PYLON FAIRINGS - RIGHT ENGINE 整体目视检查下部和后部发动机吊架整流罩-右发1. Job Set-up 开始工作A. Aircraft Maintenance Configuration T 飞机维护构型(1) Energize the ground service network (Ref. AMM TASK 24-42-00-861-801) 使用地面电源给飞机供电(参考 AMM TASK 24-42-00-861-801) . B. Safety Precautions T 安全防范(1) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do the inspection. 进行检查前确认左发和右发均关车至少5分钟。(2) Put a WARNING NOTICE to tell persons not to start the engines. 安放警告牌禁止他人启动发动机。C. Get Access to the Avionics Compartment. T 接近电子舱(1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position at access door 811. 放置工作梯ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE到位（接近门811）。(2) Open access door 811. 打开接近门811。(3) Open the protective door of the AC/DC emergency power-center 740VU. 打开740VU的保护门。D. Open, safety and tag this(these) circuit breaker(s): T 拔出以下跳开关，安装保险卡子和警告牌：PANEL DESIGNATION FIN LOCATION _FOR 4030EM1 对于4030EM1722VU FADEC B ENG 1 13KS1 D44 742VU FADEC A ENG 1 12KS1 Q73 _FOR 4030EM2 对于4030EM2722VU FADEC B ENG 2 13KS2 K49 742VU FADEC A ENG 2 12KS2 Q74 E. Deactivation of the Thrust Reverser. T 反推限动(1) Make sure that the thrust reverser is unserviceable . (Ref. AMM TASK 78-31-00-040-805)or(Ref. AMM TASK 78-30-00-040-804) .执行反推限动 (参考 AMM TASK 78-31-00-040-805)或(参考 AMM TASK 78-30-00-040-804)。F. Get Access T 接近(Ref. Fig. 601/TASK 05-24-50-991-035 SHEET 601.1)(Ref. Fig. 602/TASK 05-24-50-991-036 SHEET 602.1)如图Fig. 601和Fig. 602(1) Put an ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position at the pylon leading edge (zones 454, 464). 放置工作梯ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE到位（区域454和区域464）。(2) Remove the access panels: 拆下接近盖板：(a) For pylon 1 对于1号吊架：454BL 454CL , 454KL 454EL 454ML , 454GL 454HL 454JL , 454BR 454NR 454KR , 454ER . (b) For pylon 2 对于2号吊架：464BL 464CL , 464KL 464EL 464ML , 464GL 464HL 464JL , 464BR 464NR 464KR , 464ER . 2. Procedure 步骤A. Inspection. 检查(1) Do a general visual inspection of the lower and rear pylon fairings T (zones 454, 464). 整体目视检查下部和后部发动机吊架整流罩（区域454, 464）(2) Make sure that: T - there is no damage (corrosion, leaks or cracks) on all the parts of the components and the structure you can see, - all the installations (ducting, piping, wiring) are attached correctly. 确认以下：- 检查区域内所见部件和结构上所有零件无损坏（包括腐蚀，渗漏，裂纹）。- 确认安装部件（线束、管道等）正确安装到位。Only applicable to TRENT 700 / 仅适用于TRENT 700发动机:(3) Make sure that: there is no damage (ageing, crazing or cracks) on seal shown in figure. T 确认图示中的封严无损伤（包括老化，龟裂，破裂）。NOTE:Replacement of the seal shown in figure need more elapsed time. Ifdamage is detected, replace them.注 释：由于此处封严在航线更换，需要很长的停场时间，发现上述损伤，请安排更换。ALL/适用于所有飞机3. Close-up 结束A. Reactivation of the Thrust Reverser. T 解除反推限动(1) Make sure that the thrust reverser is serviceable (Ref. AMM TASK 78-31-00-440-805)or (Ref. AMM TASK 78-30-00-440-804) . 使反推恢复到可用状态 (参考 AMM TASK 78-31-00-440-805)或(参考 AMM TASK 78-30-00-440-804) .B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): T 移除警告牌和保险卡子，闭合以下跳开关：PANEL DESIGNATION FIN LOCATION _FOR 4030EM1 对于4030EM1：722VU FADEC B ENG 1 13KS1 D44 742VU FADEC A ENG 1 12KS1 Q73 _FOR 4030EM2 对于4030EM2：722VU FADEC B ENG 2 13KS2 K49 742VU FADEC A ENG 2 12KS2 Q74 C. Installation of the Panels. T 安装以下盖板：(Ref. Fig. 601/TASK 05-24-50-991-035 SHEET 601.1)(Ref. Fig. 602/TASK 05-24-50-991-036 SHEET 602.1)如图Fig. 601和Fig. 602(1) Make sure that the work area is clean and clear of tools and other items. 确认工作场所干净整洁，无工具等外来物。(2) Install the access panels: 安装接近盖板：(a) For pylon 2 对于2号吊架464BL 464CL , 464KL 464EL 464ML , 464GL 464HL 464JL , 464BR 464NR 464KR , 464ER . (b) For pylon 1 对于1号吊架454BL 454CL , 454KL 454EL 454ML , 454GL 454HL 454JL , 454BR 454NR 454KR , 454ER . D. Close Access T 关闭接近(1) Close t