1945414_217_AT-534100-200-813VIP

Hong Kong Airlines Limited香港航空有限公司03110-01Hong Kong Airlines MEDHong Kong Airlines LimitedWO NO/工作指令号SEQ NO/序列号WOHA331945_217_414DIC 培训方式1945414通用类/GenericTitleGENERAL VISUAL INSPECTION OF FUSELAGE INTERNAL STRUCTURE BETWEEN FR 73 AND FR 80 BELOW MAIN DECK FLOOR INCLUDING MAIN DECK FLOOR STRUCTUREMcd&Rev/厂家工卡&修订日期标题整体目视检查FR73-FR80客舱地板下面机身内部结构，包括主舱地板结构AMM 53-41-00-200-8132014-07-01A/C/飞机号Subtask No/工卡号JC Rev/工卡版本号Workarea/工作区域Skill/工种Man Hour/工时BLNYAT-534100-200-813HR001003机身/AirframeMDIC04:00MP Item/MP号Baseline/依据MP REV/ MP版本号Station/维修站Threshold/首检Interval/重复检HA33-534128-01-1MPD534128-01-1,MRB534128-01-1Issue 2 Revision 5PVG2190 CA2190 CAAccess Panels/接近盖板Zones/区域Written/编写Approved/批准822 162ZW171 1722014-09-242014-09-26TOOLS/工具TOOLS NECESSARY/必须工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注198A24403000000CABLE HOLDING STRAPTO1ALL(必需/Necessary)298A52307628000LOCK - SAFETY, CARGO DOOR ACTUATORSTO1ALL(必需/Necessary)398F52308227002SUPPORT STRUT - CARGO DOORTO2ALL(必需/Necessary)或/Or 98F52308279000TOOLS IF NECESSARY/视情工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIAL/航材NOTE:OPERATOR MUST GET AND INSTALL THE PARTS THAT CORRESPOND TO THE RELATIVE WORKORDER NO.注释：请工作者严格按照工作指令号领取预定的航材装机PARTS AND MATERIAL NECESSARY/必须航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注1CML11-004CLEANERCH1ALL(必需/Necessary)2CML19-003CLEANING ABSORCH1ALL(必需/Necessary)PARTS AND MATERIALIF NECESSARY/视情航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注1CML15-008COMPOUNDCH1ALL(视情/As Necessary)或/Or CML15-0072CML15-005ACOMPOUNDCH1ALL(视情/As Necessary)3CML15-005CORROSION PREVENTIVE COMPOUND, TEMPORARYCH1ALL(视情/As Necessary)或/Or CML15-0064CML08BAA9SOLVENT GENERAL PURPOSECH1ALL(视情/As Necessary)5CML12ADB1ANTICORROSIONCH1ALL(视情/As Necessary)IMPORTANT NOTE:In the event of any discrepancies between the Chinese instruction and the English instruction, the English procedure should prevail.Record Additional Work/Findings(If Applivable) Reference No. Certificate of Release to Service (* Tick as appropriate # Different crews should perform the work on each of the systems)Certifies that the work specified, except as otherwise specified, was carried out in accordance with HKAR-145and in respect to that work, The aircraft / aircraft components are considered ready for Release to Service. HKA Approval No: AI / 135 / 706 * HNAT Approval No.: JMM 076, D3039 * HNAT Approval No.: JMM 047, D101115* HNAT Approval No.: JMM 049, D500023 * CASL Approval No: AI / 101 / 798 * TAECO Approval No.: DAI / 89 / 1295 * HAECO Approval No: DAI / 1 / 853 * SIAEC Approval No: AWI / 01 * STARCO Approval No.: JMM 039, D.200078 * SMECO Approval No: JMM 081, D.400009 * AMECO Approval No.: JMM001,D.101131* Other: * Signature:_ Authorization No.:_ Date:_AT-534100-200-813 HR001003 W/O:1945 AC:BLNY页码，2 / 5工卡Job card:HA33-534128-01-1TITLEGENERAL VISUAL INSPECTION OF FUSELAGE INTERNAL STRUCTURE BETWEEN FR 73 AND FR 80 BELOW MAIN DECK FLOOR INCLUDING MAIN DECK FLOOR STRUCTUREPerfInsp标题整体目视检查FR73-FR80客舱地板下面机身内部结构，包括主舱地板结构工作者检查者GENERAL VISUAL INSPECTION OF FUSELAGE INTERNAL STRUCTURE BETWEEN FR 73 AND FR 80 BELOW MAIN DECK FLOOR INCLUDING MAIN DECK FLOOR STRUCTURE整体目视检查FR73-FR80客舱地板下面机身内部结构，包括主舱地板结构1. Job Set-up / 工作准备A. Get Access / 接近 M (1) Open the AFT cargo compartment door (Ref. AMM TASK 52-30-00-010-801) and install the actuator safety lock (Ref. AMM TASK 52-30-00-480-801). 打开后货舱门(参考AMM TASK 52-30-00-010-801)并安装作动筒安全锁(参考AMM TASK 52-30-00-480-801)。(2) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position below the AFT cargo compartment door. 在后货舱门下方放置工作梯。(3) Open the door 162ZW. 打开舱门162ZW。(4) Move the insulation away from the structure as necessary, so that you can see the inspection area (Ref. AMM TASK 25-80-00-000-801). 按需将隔热层从结构上移开，以便能够看见检查区域(参考AMM TASK 25-80-00-000-801)。 B. Preparation of the Inspection Area M (1) Make sure that the inspection area is clean to do a satisfactory inspection of the area. 请确保检查区域的足够清洁，以满足检查的需要(2) If not, clean the inspection area with Material No. 08BAA9 (Non Aqueous Cleaner-General - -) and a lint-free cotton cloth Material No. 14SBA1 (Textile-Lint free Cotton -) . 若不清洁，请使用抹布和清洁剂清洁(3) If there is a TPS layer and if it does not let you do a satisfactory inspection, remove the TPS layer .(Ref. AMM TASK 51-78-00-916-801) . 若有TPS保护层影响检查，请去除TPS保护层（参考AMM TASK 51-78-00-916-801）2. Procedure / 工作步骤A. Visual Inspection (Ref. Fig. Internal Structure between FR73 and FR80 below Cabin Floor Including Cabin Floor Structure SHEET 1)目视检查(参考Fig. Internal Structure between FR73 and FR80 below Cabin Floor Including Cabin Floor Structure SHEET 1)(1) Do a visual inspection of the fuselage internal structure between FR73 and FR80 below the T DICcabin floor including the cabin floor structure for corrosion. 目视检查FR73-FR80客舱地板下面机身内部结构包括主舱地板结构是否有腐蚀。(2) If you find corrosion, refer to SRM 51740000. T 如果发现腐蚀，参考SRM 51740000。 B. Temporary Protection System 临时保护系统CAUTION: DO NOT APPLY TEMPORARY PROTECTION SYSTEM (TPS) TYPE 3 TO THE MOVABLE COMPONENTS. ONLY TPS TYPE 1 GRADE 2 MUST BE USED. IF YOU DO NOT OBEY THIS INSTRUCTION, THE MECHANISMS WILL NOT OPERATE CORRECTLY. 注 意：禁止在活动部件上使用临时保护层TYPE 3，只能使用TPS TYPE 1 GRADE 2 若不遵守此使用说明，会使机构不能正确操作(1) If there is a TPS layer, make sure that it is in the correct condition T (Ref. AMM TASK 51-78-00-916-801) . 若有TPS保护层，请确保其处于良好的状态（参考AMM TASK 51-78-00-916-801）NOTE: Airbus recommends that you always apply a new layer of TPS. This is to make sure that the TPS layer continues to give satisfactory corrosion protection. If, after the check, you think that the TPS layer is in the correct condition, you can spray a new layer on the existing layer. 注释：空客建议使用全新的TPS保护层，这样能够确保持续良好的防腐效果，若检查后， 确认TPS保护层处于良好的状态，也可在已存在的保护层上喷涂新的保护层 (2) If the TPS layer has local damage, remove the damaged TPS layer T (Ref. AMM TASK 51-78-00-916-801) and apply a new layer of Material No. 12ADB1 (Corrosion Preventive Compound-Water Displacing & Heavy Duty Hard Film -) on the inspection area (Ref. AMM TASK 51-78-00-916-801) . 若TPS有局部损伤，去除损伤的TPS保护层，（参考AMM TASK 51-78-00-916-801）并在检查区域用No. 12ADB1建立新的保护层 (3) Apply a full new layer of Material No. 12ADB1 (Corrosion Preventive Compound-Water T Displacing & Heavy Duty Hard Film -) on the inspection area (Ref. AMM TASK 51-78-00-916-801) if, before the inspection: 若检查前进行了以下程序，请用No. 12ADB1建立全新保护层：- You removed the TPS layer, or 去除TPS保护层，或者- You cleaned the inspection area with high-pressure water, steam, solvents and/or cleaning agents. 用高压水，蒸汽，溶剂和/或清洁剂清洁检查区域3. Close-up / 工作收尾A. Close Access / 关闭接近 (1) Make sure that the work area is clean and clear of tools and other items. M 确保工作区域洁净并无工具及