MAOTS2519101-Cabin Refurbishment12_HA33S-25-103-130 - Rev 00

Hong Kong Airlines Limited香港航空03110-01Hong Kong Airlines MEDHong Kong Airlines LimitedWO NO/工作指令号SEQ NO/序列号培训方式MAOTS251910112通用类/GenericTitleDetailed examination of the attendant seatsMcd&Rev/厂家工卡&修订日期标题详细检查乘务员座椅NONEA/C/飞机号Subtask No/工卡号JC Rev/工卡版本号Work area/工作区域Skill/工种Man Hour/工时B-LHDHA33S-25-103-130Rev. 00客舱/CabinTRIM04:00MP Item/MP号Baseline/依据MP REV/ MP版本号Station/维修站Threshold/首检Interval/重复检-Rev. 001C1CAccess Panels/接近盖板Zones/区域Written/编写Approved/批准NONE2002019-04-102019-04-10TOOLS/工具TOOLS NECESSARY/必须工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注TOOLS IF NECESSARY/视情工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIAL/航材NOTE: OPERATOR MUST GET AND INSTALL THE PARTS THAT CORRESPOND TO THE RELATIVE WORK ORDER NO.注释：请工作者严格按照工作指令号领取预定的航材装机PARTS AND MATERIAL NECESSARY/必须航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIAL IF NECESSARY/视情航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注12B7095-1DCQCovers HeadrestCHARALL22B7098-1DCQCovers Seat PanCHARALL32B7097-1DCQCovers BackrestCHARALL42B7096-1DCQCovers Upper Back RestCHARALL52B7095-11DCQCovers HeadrestCHARALL62B7098-11DCQCovers Seat PanCHARALL72B7097-11DCQCovers BackrestCHARALL82B7096-11DCQCovers Upper Back RestCHARALL918-0100K0KZN-05ATTENDANT SEAT SAFE BELTCHARALLIMPORTANT NOTE:In the event of any discrepancies between the Chinese instruction and the English instruction, the English procedure should prevail.Record Additional Work/Findings(If Applicable) Reference No. Certificate of Release to Service (* Tick as appropriate # Different crews should perform the work on each of the systems)Certifies that the work specified, except as otherwise specified, was carried out in accordance with HKAR-145and in respect to that work, The aircraft / aircraft components are considered ready for Release to Service. HKA Approval No: AI / 135 / 706 * HNAT Approval No.: JMM 076, D3039 * HNAT Approval No.: JMM 047, D101115* HNAT Approval No.: JMM 049, D500023 * CASL Approval No: AI / 101 / 798 * TAECO Approval No.: DAI / 89 / 1295 * HAECO Approval No: DAI / 1 / 853 * SIAEC Approval No: AWI / 01 * STARCO Approval No.: JMM 039, D.200078 * SMECO Approval No: JMM 081, D.400009 * AMECO Approval No.: JMM001,D101131* Other: * Signature:_ Authorization No.:_ Date:_页码，1 / 10工卡Job card:TITLEDetailed examination of the attendant seatsPerfInsp标题详细检查乘务员座椅工作者检查者WARNING: PLEASE OBEY ALL WARNING AND CAUTION OF REFERENCE MANUAL,OTHERWISE IT SHOULD CAUSE PERSONAL INJURE OR DAMAGE TO EQUIPMENT.警 告：请遵守所参考手册的所有警告和注意事项，否则会造成人员伤害或设备损坏。1. Job Set-up A. Energize the ground service network (Ref. AMM TASK 24-42-00-861-801) . 2. Procedure 2.1 PART ONE：General Visual Inspection of Seat Structure A. General Visual Inspection of Seat Structure (Ref. Fig. 25-22-00-991-00300-00-C / SHEET 1/1 - Cabin Attendant Seat - Free Standing)(Ref. Fig. 25-22-00-991-00200-00-D / SHEET 1/1 - Cabin Attendant Seat - Wall Mounted)(1) Open the stowage compartment and remove all the emergency equipment. (2) Remove the seat cushions. (3) Make sure that the structure of the seats is not damaged or cracked. 2.2 PART TWO: Operational Check and Visual Check of Seat Belts and Belt Attachments A. Do the Operational Check of the Cabin-Attendant Seat-Belts (Ref. Fig. 25-22-00-991-00500-00-A / SHEET 1/2 - Seat Belts - Cabin Attendant Seat) (Ref. Fig. 25-22-00-991-00500-00-A / SHEET 2/2 - Seat Belts - Cabin Attendant Seat)(1) Make sure that the metal attach fitting and buckles have no cracks or other damage. (2) Make sure that the seat-belt buckle locks/unlocks correctly. (3) Make sure you can adjust the length of the seat belt correctly. (4) Make sure you can pull out the shoulder harnesses smoothly and that they automatically go back into their reels. (5) Make sure that the shoulder harness locks when you pull hard and the it unlocks when you release the tension. B. Do the Visual Check of the Cabin-Attendant Seat-Belts Webbing (Ref. Fig. 25-22-00-991-00700-00-A / SHEET 1/2 - Seat-Belt Webbing Life)(Ref. Fig. 25-22-00-991-00700-00-A / SHEET 2/2 - Seat-Belt Webbing Life)(1) Do a check of the webbing for damaged stitching, injurious marks, brokenfabric threads and chafe marks. (2) There are four classified types of web fraying: - Class I: The webbing has fraying across the full width - Class II: Each side of the webbing has fraying but the fraying is not continuous across the full width - Class III: Only one side of the webbing has fraying - Class IV: The fraying is the result of a small cut or clear edge break. (3) Replace the webbing if: - If the thickness of the lap belt or inertia reel webbing increases more than 0.075 in. (1.9 mm).- If the web edge is cut or torn deeper than 0.1 in. (2.5 mm). - If the fraying is more than 10% of the web width - If the amount of fraying is more than 8 in. (203.2 mm) of the web length - If there are more than 15 broken threads in other locations than the edge - If more than 30 stitches in the stitch-pattern are broken. 2.3 PART THREE: General Visual Inspection of Seat Attachment Points A. General Visual Inspection of the Seats Attachment Points - Free Standing Seats (Ref. Fig. 25-22-00-991-00300-00-C / SHEET 1/1 - Cabin Attendant Seat - Free Standing)(1) Open the stowage compartment and remove all the emergency equipment. (2) For a seat-track attached seat: (a) Make sure that the locking trunnions are correctly installed. (b) Make sure that the locking trunnions are not damaged and have no corrosion. (3) For a hard-point attached seat: (a) Remove the seat cushions. (b) Make sure that the attachment bolts are correctly installed. (c) Make sure that the attachment bolts are not damaged and have no corrosion. (d) Install the seat cushions. (4) Install all the emergency equipment and close the stowage compartment. B. General Visual Inspection of the Seat Attachment Points - Wall Mounted Seats (Ref. Fig. 25-22-00-991-00200-00-D / SHEET 1/1 - Cabin Attendant Seat - Wall Mounted)(1) Open the stowage compartment and remove all the emergency equipment. (2) Remove the seat cushions. (3) Make sure that the attachment bolts are not damaged, have no corrosion and are correctly installed. (4) Make sure that the elastomer mounts of the upper bolts are in good condition. (5) Install the seat cushions. (6) Install all the emergency equipment and close the stowage compartment. 2.4 SEAT COVERSA. Pull the headrest cushion and cover assembly, the seat pan cushion and cover assembly,the backrest cushion and cover assembly, and the upper back cushion and cover assemblyfrom the hook and loop fasteners per CMM TASK 25-21-66-010-803-A01. _B. Pull the headrest cover assembly from one of the corners and remove it from the headrestcushion per CMM TASK 25-21-66-010-804-A01. C. Pull the seat pan cover assembly from one of the corners and remove it from the seat pancushion per CMM TASK 25-21-66-010-805-A01.D. Pull the backrest cover assembly from one of the corners and remove it from the backrestcushion per CMM TASK 25-21-66-010-806-A01. _E. Pull the upper back cover assembly from one of the corners and remove it from the upperbackrest cushion per CMM TASK 25-21-66-010-807-A01.F. Put the upper backrest cushion carefully into the upper back cover assembly per CMM TASK 25-21-66-410-809-A01. _G. Put the backrest cushion carefully into the backrest cover assembly per CMM TASK 25-21-66-410-810-A01. _H. Put the seat pan cushion carefully into the seat pan cover assembly per CMM TASK 25-21-66-410-811-A01. _I. Put the headrest cushion carefully into the headrest cover assembly per CMMTASK 25-21-66-410-812-A01. _J. Align the hook and loop fasteners on the headrest cushion and cover assembly, the seat pancushion and cover assembly, the backrest cushion and cover assembly, and the upperback cushion and