办理烟草专卖零售许可证的条件和程序范文

办理烟草专卖零售许可证的条件和程序 办理烟草专卖零售许可证实行“一站式”服务，坚持“首问负责制原则”一、申请公民、法人或者其他组织从事烟草专卖品零售业务的，应当依法向烟草专卖行政主管部门申请领取烟草专卖零售许可证。申请人应当按申请类型提交相应的申请材料并对材料的真实性负责。 申请人提出申请时，一般应当以书面方式提交相应类型的格式文本。通过信函、电报、电传、传真、电子数据交换和电子邮件等方式提出申请的，由受理机关将其转换为格式文本并经申请人确认。申请人可以委托代理人提出申请，代理人应当提供委托书、委托人及代理人的身份证明。申请新办零售类许可证，应当提交下列材料：（一）烟草专卖许可证新办申请表；（二）个体工商户、法定代表人或企业负责人的身份证明；（三）房屋权属证明或房屋租赁协议；（四）审批机关规定需要提供的其他材料。二、受理烟草专卖局收到申请人提交的申请材料后，应当根据下列情况分别作出处理：（一）申请事项依法不需要提出烟草专卖许可证申请的，应当即时告知申请人不受理。（二）申请事项不属于本烟草专卖局职权范围的，应当即时告知申请人向有关烟草专卖局申请。（三）申请材料存在可以当场更正的错误的，应当允许申请人当场更正。（四）申请材料不齐全或不符合法定形式，申请人不能当场更正的，应当当场或者在5日内出具烟草专卖许可证申请材料补正告知书，一次性告知申请人需要补正的全部内容。逾期不告知的，自收到申请材料之日起即为受理。（五）申请人在烟草专卖许可证申请材料补正告知书规定的期限内未补正申请材料，或补正的材料仍不齐全或不符合法定形式的，烟草专卖局应当出具烟草专卖许可证不予受理通知书。（六）申请事项属于法定职权范围，申请材料齐全、符合法定形式，或者申请人已按照要求提交全部补正申请材料的，应当受理烟草专卖许可证申请并出具烟草专卖许可证受理通知书送达申请人。三、审批与发放经审查，申请人的申请符合法定条件的,烟草专卖行政主管部门应当自受理之日起20日内作出行政许可决定。二十日内不能作出决定的,经本单位负责人批准,可以延长十日,并应当将延长期限理由告知申请人.但法律.法规另有规定的,依照其规定.烟草专卖行政主管部门应当自作出予以发放烟草专卖许可证决定之日起十日内向申请人送达烟草专卖许可证.依法作出不予发放烟草专卖零售许可证的书面决定的，应当向申请人说明理由，并告知申请人享有依法申请行政复议或者提起行政诉讼的权利。申请烟草专卖零售许可证，应当具备下列条件：1.有与经营烟草制品零售业务相适应的资金；2.有与住所相独立的固定经营场所；3.符合当地烟草制品零售点合理布局的要求；4.国务院烟草专卖行政主管部门规定的其它条件。有下列情形之一的，不予发放烟草专卖零售许可证：1.经营场所基于安全因素不适宜经营卷烟的； 2.中、小学校周围；3.取消从事烟草专卖业务资格不满三年的；4.因申请人隐瞒有关情况或者提供虚假材料，烟草专卖行政主管部门作出不予受理或者不予发证决定后，申请人一年内再次提出申请的；5.因申请人以欺骗、贿赂等不正当手段取得的烟草专卖许可证被撤销后，申请人三年内再次提出申请的；6.未领取烟草专卖零售许可证经营烟草专卖品业务，并且一年内被执法机关处罚两次以上，在三年内申请领取烟草专卖零售许可证的；7.国务院烟草专卖行政主管部门规定的其他不予发证的情形。勿忘国耻当思国运.抚今追昔,百感化作一念：当苦日子离去的时间越久远,当富日子光临的越急匆,我们心系国家、民族的命运the same direction of rotation 90 or 180 for; after each disc rotor when measuring position alignment of the two half coupling constant, should also be in terms of accuracy and consistency. Surface deviation measurement, must in every 180 degrees corresponding to the two radii are equal to each other in order to eliminate errors caused by movement of the rotor. Only a support bearing of the rotor, WA couplings, such as the use of temporary leave the Center, should pay attention to keep the rotor in the measuring process in the center of the bearing oil retaining the nest does not change. Steam oil block, there should be sufficient clearance between the rotor and, in rotors make sure rotor is not on the block or seal oil. At the time of measurement, connections are not allowed between two rotors, each in a free State. Not allowed in case of assembled sleeve, Center work on the toothed coupling. Coupling tool should have adequate stiffness, installation must be secure and reliable. Coupling Center using a dial indicator, the table should be put in prison and avoid touching, to ensure correct measurement. Coupling disc after a week to return to the original position, circumference of dial gauge reading should be able to go back to the original value. When measuring the clearance of end, into the feeler of the gap should not exceed four at a time, when the gap is too large, you can use the gasket with the feeler gauge measurement of gauge blocks or finishing. bearing surface, markup should be in accordance with the mounting support pads, and retest the thickness. Once the lifting cylinder measurement of surface and internal cylinder surface height difference, compared with the origin