服务工程师（高级班）测试题目

Test service engineers (advanced class) 服务工程师测试（高级班） name:office. 名称 ： 办事处： 1. How is the automatic cutting height in type HPP 380 without automatical grooving realized? 如何使没有自动开槽功能的 HPP380 实现自动切割的高度？ Hydro stop 停止液压 Main saw cylinder (same pressure on both sides) 主锯的气缸（两边压力相等） Adjustable mechanical angle in 4 steps 用 4 个步骤调节机械角度 2. How is the book height in the HPP 380 determined? HPP380 的预定高度如何被设定？ The pressure beam measures the material 通过压梁测量材料 With entered dates from the CADmatic 利用已设定在 CAD 里的数据 With sensor (optical signals) 利用传感器（光感信号） 3. How is the automatic cutting length realized? 现自动切割的长度如何被设定？ With entered dates from the CADmatic 利用已设定在 CAD 里的数据 With light scanner in connection with the measuring system of saw carriage 利用锯车测量系统与激光扫描仪的链接 With the sensors around the cutting line 利用锯切线附近的传感器 4. In which situation you can tell the costumer the username install and corresponding password for that level? password is:. 在下列哪种情况下你可以告诉客户用户名“安装”和这一级别相对应的密 码？ 密码为： If it is necessary 如果需要 In special situations 在特殊情况 Never 从不 5. How it is guarantied that the pressure beam drives parallel to the top of the material in all models from Holzma 如何确保压梁在所有 HOLZMA 机型上部的板上平行运行 Guidance with rack (on machine body) and pinion (on pressure beam) 机身导轨上的锯条和压梁上的齿轮 Guidance with rack on machine body and pinion on both sides of the pressure beam, which are connected with a shaft 机身导轨上的锯条和压梁两边轴上的齿轮 With accurate cylinders, which layers the pressure beam 利用精确压梁上的气缸 6. In what typ of machine is this function key not used? 此功能不被用于下列哪种机型？ HPP 180 HPP 350 HPP 380 7. How do you adjust the stroke of the central side pressure device in accordance to the material (e.g. thin materials) ? 你如何根据材料（例如：薄板）调整测压装置上的靠板？ With the potentiometer of the side pressure device on the control panel. 利用控制仪表上的测压装置旁的分压计 With a parameter 利用分压计 Function is automatically done by the control.通过控制功能自动完成 8. How is the upper edge of the clamp finger adjusted on the HPP Typs? HPP 机型上部边缘的夹具如何被调整？ Exactly on the level of the machine table 正好在机器台面上 One or two degrees above level of machine table 高于机器台面 1-2 个度 One or two degrees lower than level of machine 低于机器台面 1-2 个度 9. What is the minimal compressed air pressure for Holzma panel saws? Holzma 开料锯压力最少不能小于？ 4 bar 6 bar 8 bar 10. What maximal saw blade projection in realized on a HPP 180 ? HPP180 的锯片突出部分最高能设定多少？ 72 mm 80 mm 95 mm 11. How to adjust the referenz point of the program fence? 如何调整程控推板器的参考点 The end of the finger must be between.