槽针机十大常见问题（Ten common problems of slot needle machine）

1、槽针机十大常见问题（Ten common problems of slot needle machine）Ten common problems of slot needle machinefix L1 a yarn or fuzz yarn1. guide needle deviation, guide needle needle hole wear, a guide needle loose.2. slot needle needle crooked or needle groove cracks, groove needle loose. The grooved needle is no

2、t straight enough and is pulled and bent.The first train to the needle core just inside the needle in the groove position, ensure the basic core needle needle in the groove inside the slot; and then slow to core needle head and the needle groove is almost as high position, ensure the needle hook wil

3、l not deviate from the groove around the needle core too much better let them on the same line.The bottom of the 3. pin core is tilted off, or the needle core is bent, and the needle core is too far away or too close to the groove pin.4. sink leaves slanting or uneven.5. cross checked yarn.Collision

4、 between 6. flower pin firing pin or working line caused by.Burr 7. pan head on the edge of a root (less)8. needle before moving position is not enough, resulting in fluff broken (tension will make the comb forward, position is small, too tight force will also make a yarn)9., the flower time is too

5、fast, the cotton yarn into the needle hook.10. here, the ring leaves are partial or broken.two fix L2 a yarn (or run)1. guide needle wear.2. guide needle deviation.3. and L3 L4 in a needle collision.4. L2 tension is too loose.The 5. L2 guide needle eats too deep.6. L2 guide needle loose needle.Go th

6、rough 7. yarn burr.8. comb head fastening screws loose.three repair the running yarn1. flowers too deep.2. cross checked yarn.ThreeA pin between the lines of work collides.No 4. threads of raw materials.5., the yarn path has burr or stuck in the flower comb gap.6. flower needle pinhole wear, needle

7、needle hair ball.7. warping tension is too loose, yarn weight is not enough.8. chain block wear or chamfer is not worn well, cause time is too slow, too fast, move needle not sure.9. axis imbalance.four repair missing needle1. guide needle, needle spacing, guide needle is too shallow.The 2. grooved

8、needle is crooked and the slot needle is too short.3., the flower yarn tension too tight or wear wrong yarn, yarn at the carding section a bit stuck.4. needle core wear or bias, needle core loose.5. L1 comb screw loose (connected to yarn)6. needle forward movement time is too fast or too slow.7. yar

9、n tension is too tight (rachides imbalance) common schlagblech.8. off coil partial.9. L1 tension spring force is too loose, not reply.10. machine level can not, too much vibration.11. workshop temperature is too high or too low.five repair a spandex1. spandex needle bias.2. pins are too deep.3. sink

10、 slices askew.4. tension tight.5. raw material problems.6. spandex needle on the edge of a single needle loose.six rotten edges1. groove needle damage; needle core is partial or loose; subsidence slice slants. The needle core is too close or too far away from the grooved needle2., off the loop, brok

11、en or partial leaves, off the grid plate wear.3. L1 or L2 needle bias.4. L1 or L2 tension tight.5. L2 yarn wrong (example double wear too much)SixRoll pulling device (loose wrapping wear), which causes difficulty in unseating.7. off circle sheet yarn too much or not clean shell.8., L1, L2 eat the ne

12、edle is too shallow, so that can not be circle and pad yarn.9., there is a problem with organization chain (process, the situation is less).The 10. is used instead of the side rachides yarn, must see whether rachides balance and counterweight.11. knitting after a long time of operation, the needle,

13、needle core bed guide shaft are worn, see the needle bed and off the circle plate, needle bar and the needle core is too close to the bed.seven a large area of broken L1 yarn1. density gear mismatch (traction failure) or side spindle chain broken.2. pull, roll, double line break.3. place a foreign o

14、bject (such as paper, etc.) into a drum.4., tension, spring break or too loose.5., the organization of worm gear connection spindle belt broken.6., EBA electronic delivery error, send through the amount of access is too large, or sent to the motor line failure, stop the delivery.7. a foreign object,

15、 such as a weight block, falls into the L1 and is stuck between the L2 combs. Comb chain block, chain cut shift, chain block fall off.8. the comb head screw is broken (less often).eight appear in the wrong place1. rotor wear2. comb head screw loose.3., broadsword or bird head screw is not locked, th

16、e needle is apart from the head.4., there are waste yarn fell into the flower comb drum inside, resulting in more wrong flowers.5. the last few of the comb reinforcement screws are broken or loosened.6. the comb is not tight enough to lubricate.SevenThe restoring spring is not enough.8., synchronous

17、 belt loose or damaged, causing time is too slow.9. workshop temperature is too high or too low, resulting in needle spacing instability.10., the wear of the worm gear box is seriously worn and the time is too slow.11. loose screw for the first guide of the comb head.nine partial needle1. top adjust

18、ing screw is not locked.2. plug loose.3. flower tension spring is not tight enough, resulting in insufficient recovery position.4., the flower comb slider too much fluffy, flower comb occasionally stuck.5. flower needles loose, flower needle and other runway flower needle hit, hit, shifted.6. runway

19、 hook yarn fault, twisted yarn hookten fabric defects caused by needle coreOne, the needle core is too highThe needle core does not ring well, the coil is gathered at the tip of the needle and becomes a bad coil, the needle core goes too far beyond the needle and damages the coil.Two, the needle core is too lowWhe