VOLVO资料英文缩写汇总

1、英文缩写：PS (Program start)项目开始PSC (Program strategy confirmation)项目策略确定PTCC (Program Target Compatibility Check point)项目目标分解PTC (Program Target Confirmation)项目目标确定PA (Program Approval)项目批准LR (Launch Readiness)投产准备就绪LS (Launch Sign Off)投产签收J1 (Job1)量产Use for tooling kick off. 用于开模Purchasing Related Proc

2、ess/采购相关的流程RFQRequest for quotation which include Commercialdocument and ESOW. Commercial document tells thecommercial items and ESOW tells the productinformation and requirements.询价书包括了商务文件和产品工程规范和要求（ESOW）ESOWESOW1 based on first version drawing for quotationESOW2 based on 2nd version drawings for

3、nominationESOW3 based on 3rd version drawing for CPAESOW1 基于第一版图纸，用于询价ESOW2 基于第二版图纸，用于确定供应商ESOW3 基于第三版图纸，用于签订CPACPACPA is a commercial contract between Volvo andsuppliers for the commodities. It is for the commoditiesprice.CPA是沃尔沃和供应商之间的关于零件价格的合同。Tooling order / 模具订单Tooling order is an order to kick

4、 off suppliers toolingwith commercial and engineering perspectives.模具订单是沃尔沃从工程和商务两方面来启动供应商的模具工作。PPAPRefer to STA training later参考后面STA的培训PurchasingDrawing related Process/图纸相关流程V01st released version drawing. ESOW1 use it. Design supplier need release V0drawing to Volvo第一版图纸用于ESOW1。设计供应商需要发布V0数据到Vol

5、vo 系统V12nd released version drawing. ESOW2 use it. Design supplier need releaseV1 drawing to Volvo第二版图纸用于ESOW2 。设计供应商需要发布V0数据到Volvo 系统V23rd released version drawing. ESOW3 use it. Can be used for tooling design.Design supplier need release V3 drawing to Volvo第三版图纸用于ESOW3和模具设计。设计供应商需要发布V2数据到Volvo 系统F

6、DJLast released version drawing. Used for tooling kick off. Design supplier needrelease FDJ drawing to Volvo最终版图纸用于开模。设计供应商需要发布V0数据到Volvo 系统Builds/装车活动：M1 buildM1 build is to verify under body. So under body relatedparts are affected.M1装车是为了验证下车的设计，所以只有下车体的零件影响到。E3/E4 build / E3/E4装车E3/E4 build is t

7、o verify electrical parts function (nodimension requirement). All body electrical parts are3.320affected. Chassis and PT electrical parts are notaffected.E3/E4装车是为了验证车身电子零件的性能（对几何尺寸没有要求），车身电子相关零件需要支持该装车。底盘和动力系统的电气相关的零件不需要支持。MTO Build (Machine Try Out Build)MTO build is to verify BIW (body in white)

8、and bodyshop process. All stamping parts are affected. No anytrim parts are needed. Build will only in body shop.Parts must be from job1 tooling. This build is beforeVPMTO是为了验证白车身和焊装工艺的一次装车，只在焊装车间进行，只有冲压件会影响到，总装零件不需要支持。所有零件必须是量产模具制作的。MTO装车发生在VP装车之前。VP build (Verification Prototype Build)VP build is

9、to verify whole vehicle. All commoditiesaffected. Parts must be from job1 tooling.VP装车验证整车设计，所有零件都需要支持，所有零件必须是量产模具制作的。TT build (Tooling Try Build)TT build is first time to verify the job1 intend process.All parts must be from job1 tooling and process. Buildquantity is normally less than 100 carsTT装车

10、是第一次验证量产工艺的装车，所有零件都必需从量产意图工艺制作，一般装车数量少于100辆PP build (Pilot Production Build)PP build is to verify job1 process with more quantitiesvehicle. All commodities affected. Parts must bePSW/SOP level.PP装车是中批量装车验证Job1工艺，所有零件都需要支持，且要达到PSW/SOP水准。焊装零件：PCF Definition/PCF定义PCF: Body Parts CoordinationPCF: 焊装零件几何尺寸检查PCF Methods/TPC方法Use fixtures to simulate standard body then check thebody parts dimension.用检具来模拟标准车身，以此来检查焊装零件的几何尺寸。PCF PlanRefer to VPP参考VPPPCF Related Parts/PCF相关零件All body parts所有焊装的零件总装零件：TPC Definition/TPC定义TPC: Trim Parts