模具常用术语中英文对照

1、模芯 Parting Core 耐落胶 Teflon Paste局部视图Partial View 冷料 Cold Slag线切割Wire E.D.M轮廓 Contour螺纹孔 Tapping Hole连接件Fittings斜针 Angle Pin接合Engage 偏移量Offset 水塞 Water Line Plug 撬模脚Ppy Slot 重新加工Reworked 配件 Components 补偿 Compensation 平面度Parallel 倒角 Chamfer替换镶件 Interchangeable Mold Inserts 模胚 Mold Base指定吨位的注塑机Specific

2、 Press水嘴接头Water Fitting螺纹 Eyebolt Thread回针 Stop Pin二级顶出针 Sub-Leaderd Pin镶件 Mold Insert力I硬 Harden唧嘴Sprue设计筒图 Design Preliminary名称块表Title Block版本标识 Revision Level材料清单Stock List热嘴 Hotnozzle火花机Edm熔接线Weildline压机Press咂纹 Texturing梯形 Trapezoid凸缘、法兰Flange方铁 Spacer Block顶针板 Ejector Plate顶针底板 Ejector Retainer

3、Plate 垫板 Retainer Plate 后模镶针Core Pin制模 Build Mold垃圾钉Stop Pin手动滑块Hand Slide有托顶针 Shoulder Ejector Pin漏水测试Leak Test顶针板导套 Guided Ejection Bushing流道排气Runner Vents针板导柱 Guided Eject io n Leader Pin抛光 Draw Polish唧嘴 Sprue Bushing侧抽芯 Slide Action三板模延伸式唧嘴 Extension Noozzle Bulishing加强筋 Reinforcing水口板导套 Runner

4、Stripper Pin三角撑Gusset定位圈（法兰）Locating Ring柱子Bossed管钉（定位销）Dowel Pin出模斜度Draft管状管钉Tubular Dowel外廊 Contour吊环 Safety Hoist Ring落单会议Kick-off日期印 Dating Insert装卸孔 Handing Hole环保E卩 Recycling Insert运输安全带Moldstrap气顶 Air Poppet Valve码模槽Clamp Slot截水口镶件 Runner Shut-Off Insert撑头 Support Pillar早回 Early Ejector Retur

5、n螺牙 1/2-13 Eye 1/2-13Tap力1 速项 Accelerated Ejector导柱位 Leader Pin Location客户Client产品名Part Name产品编号Part No缩水 Shrinkage版本Rev下模镶件Core Block上模镶件Cavity Block小镶件 Sub-Insert下模小镶件Core Sub-Insert压紧块（铲机）Jaw硬片（摩擦 片）Wear Plate 水口铁 RunnerBar 上模水口铁 Upper RunnerBar K模水口铁 Lower RunnerBar弹簧Spring水口钩针Sprue Puller Pin 顶

6、针 Ejector Pin 撑头 Support Pillar 直身锁 Side Lock 斜度锁Inter Lock锁模板Safty BarO令（密封圈）O Ring喉塞Plug隔水片Baffrle波子螺丝（行为定位螺丝）斜顶Lifter控制开尖Switch回针Return Pin 斜导柱 Angle Pin 推板 Stripper PlateA 板 A Plate扁顶Blade出模斜波Draft手动滑块模具 Hand Slide-In Type Mold回针板Backup合模 Shutoff空隙槽 Clearance Slot导柱及导套Leader Pin Bushing水口拉 钩 Spu

7、er Puller 模框镶件 Pocket Insert 成型热固性塑料模具Thermoset Mold三 板模 3-Plat Mold分型面 Parting Line司筒 Ejector Sleeve垫圈Washer烙接线（夹水纹）Weldlin吸针 Sucker Pin回针板 Retainer Plate顶出板 Knock-Out Plate电动安全开尖 Electrical-Safety Switch 脫开 Cut Of Position预先决定Preload缓冲器Bumper方铁（垫铁）Spacer Block顶针 板Ejector Plate顶针底板 Ejector Retainer

8、 Plate 垫板 Retainer Plate精磨 Finished 通框Through Window粘后模 Stricking Core 粘水口 Sticking Sprue夹水纹 Weld Line变形 Warpage走水不平均Filling走不 齐 Short Shot 挂成品 Part Hanging 漏水 Water Leakage 刮 花（擦伤）Galling漏电Ele Leakage 困气 Air Trapping 温度 Temperature 注塑模 Injection Mold 入水 Gate 试板 Sampling倒圆Fillet公差 Toleranee突然性动作Slam

9、销针Dowel钩槽Gib有托顶针Shoulder Ejector Pin顶针板导套Guided Ejector Bushing 针板导柱 GuidedEjector Leader Pin 不干胶 AdhesiveSticker线切割Wire-Cut电火花Edm抛光 Polishing蚀纹 Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt 盖板 Cover Plate齿轮Gear油唧 Hydraulic Cylinder司筒 Ejector Sleeve导柱 Leader Pin冷料 Cold Slag压力 Pressure螺纹孔 Tapping Hol

10、e顶棍 Ejector 顶白 Stress Mark名称块表Title Block版 本标识Revision Level材料清 单Stock List斜导柱（斜边） Angle Pin 分模面 Parting Surface 披峰 Flash 缩水 Sink Mark氮化Nitride不规则四边 开彳 Trapezoid 缩水 Shrinkage 连续的Consecutive热流道 Manifold型腔数Cav No模号 Mold No 回针 Return Pin 力硬 Harden唧嘴Sprue设计筒图 Design Preliminary 丝印 Silkprint连接件Fitting粘前模 Sticking Cav替换镶件 Interchangeable Mold Insert 制 定吨位的注塑机Specific Press水嘴接头 Water Fitting 螺纹 Eyebolt Thread 倒扣 Under-Cut 锁定位 Lock楔子（铲机）Wedge高产量模量 High Volume Run