小型校园网的构建计算机网络zq

1、企业网络设计1. 课程设计目的1、增加对计算机网络软、硬件组成的感性认识初步学会典型局域网络的操作、 使用技能；2、加深理解网络分层结构概念尤其是对会话层、表示层、应用层等高层协议软件的通信功能、实现方法，掌握网络互连设备的使用及工作原理，掌握IP地址的配置；3、初步掌握局域网的设计技术和技巧培养开发网络应用的独立工作能力。2. 设计方案论证2.1设计思路2.1.1总体设计思路进行企业网络总体设计，首先，进行对象研究和需求调查，弄清企业的性质、 任务和特点，对企业的信息化环境进行准确的描述，明确系统建设的需求和条件； 其次，在应用需求分析的基础上，确定企业 In tra net服务类型，进而确

2、定系统建设 的具体目标，包括网络设施、站点设置、开发应用和管理等方面的目标；第三，确 定网络拓扑结构和功能，根据应用需求、建设目标和学校主要建筑分布特点，进行 系统分析和设计；第四，确定技术设计的原则要求，如在技术选型、布线设计、设 备选择、软件配置等方面的标准和要求；第五，规划安排企业网建设的实施步骤。2.1.2 网络设计将网络中心设在D座楼，支持远程教学，可以接入互联网，具有广域网访问的 安全机制和网络管理功能。以 D座楼为中心，用光纤连接到其它建筑物，构成校园 网光纤主干。网络结构分成三层：核心层、汇聚层、接入层。（1）终端用户包括：A座楼有48个校园网普通用户；B座楼有1个包含24个多

3、媒体用户的电子阅览室；C座楼有1个包含48个用户的多媒体教室（性能要求高于电子阅览室）D座楼是网络中心(2) 支持远程教学，可以接入互联网，具有广域网访问的安全机制和网络管理功能。(3) 各楼之间的距离为500米。由于各座楼之间的距离是 500米，而双绞线的最远距离是100米，所以基于对 条件要求的考虑，我们需要选择光纤或串行线作为传输介质。考虑传输高速率和扩 展的需求，企业网楼与楼之间采用光纤传输。网络主干采用多模光纤。网络中心到 主建筑物结点采用多模光纤连接。布线采用星形拓扑结构，这样当过渡到ATM时，不需要重新布线可使整个网络保持原有的拓扑结构。以上特点分层网络结构可以获 得良好的扩展性

4、，根据实际需求，整个企业网采用星型结构，由D座楼出发，延伸到ABC座楼。再从各个楼出发，以同轴电缆作为传输介质。由云到D座楼为A类网，由D座楼到各个楼之间为B类网，各个内部为C类网。对于整个网络的拓扑结构为混合型结构，以路由器为网络中心的星型结构，各 部门以交换机为主结点的树型结构。由于计算机与网络技术的特殊性，网络建设需要考虑以下一些因素：系统的先 进性、体统的稳定性、系统的可扩展性、系统的可维护性、应用系统和网络系统的 配合度、与外界网络的连通性、建设成本的可接受度等。2.1.3具体设计表1校园网设备选择表楼座设备型号数量A座楼RouterRouter-PT1Switch2960-242P

5、CPC-PT4RouterRouter-PT2B座楼Switch2950T-242ServerServer-PT1PCPC-PT4C座楼RouterRouter-PT1Switch2950T-242PCPC-PT2SererServer-PT1D座楼RouterRouter-PT1CloudCloud-PT1表2设备连接表楼号设备1设备2设备之间的连线A座楼RouterRouter光纤RouterSwitch交叉双绞线SwitchPC直通双绞线B座楼RouterRouter光纤、串行线RouterSwitch直通双绞线SwitchPC直通双绞线SwitchServer直通双绞线C座楼Route

6、rSwitch直通双绞线SwitchPC直通双绞线SwitchServer直通双绞线SwitchSwitch交叉双绞线D座楼RouterRouter光纤RouterCloud串行线表3主机IP地址及网关主机ip地址默认网关PC0192.168.32.2192.168.32.1PC1192.168.32.3192.168.32.1PC2192.168.33.2192.168.33.1PC3192.168.33.3192.168.33.1PC4192.168.1.3192.168.1.1PC5192.168.1.2192.168.1.1PC6192.168.5.3192.168.5.1PC7192

7、.168.5.2192.168.5.1PC8192.168.4.2192.168.4.1PC9192.16843192.168.4.1Serverl192.168.1.4192.168.1.1Server2192.168.4.4192.168.4.1表4主机IP地址及网关主机ip地址默认网关PC0192.168.32.2192.168.32.1PC1192.168.32.3192.168.32.1PC2192.168.33.2192.168.33.1PC3192.168.33.3192.168.33.1PC4192.168.1.3192.168.1.1PC5192.168.1.2192.168

8、.1.1PC6192.168.5.3192.168.5.1PC7192.168.5.2192.168.5.1PC8192.168.4.2192.168.4.1PC9192.168.4.3192.168.4.1Server1192.168.1.4192.168.1.1Server2192.168.4.4192.168.4.1拓扑图如下:BkPC-PT 如PCO J, -5960ClcJd-PT2960-OTSwitchPC-PTPCS勺PC-PIPCPTPC7号搂.3 Liter-Fsuter-PT suterSPC-PT心2-4TTSwitch 2Router-1!三匕Router-PT二号棒

9、5vqtch4PC-PTQn j -*PC-PTPCST-24PC-PTPC9PC-PTPCSServer-PTSrv&r2PC-PTPC4295QT-24Switch 5图1网络拓扑图2.2相关代码路由器D座楼的配置：Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per line. End with CNTL/Z.Router(config)#interface Serial2/0Router(c on fig-if)#%LINK-5-CHANGED: In terface Ser

10、ial2/0, cha nged state to upno shutdow n Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0Router(c on fig-if)# no shutdow nRouter(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net4/ORouter(c on fig-if)# no shutdow n %LINK-5-CHANGED: In terfa

11、ce FastEthernet4/O, cha nged state to dow n Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net5/0Router(c on fig-if)# no shutdow n %LINK-5-CHANGED: In terface FastEthernet5/0, cha nged state to dow n Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#inter

12、face Serial2/0Router(c on fig-if)# no ip addressRouter(config-if)#ip address 10.0.0.2 255.0.0.0Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0Router(config-if)#ip address 172.18.0.1 255.255.0.0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface Fas

13、tEther net4/0Router(config-if)#ip address 172.16.0.1 255.255.0.0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net5/0Router(config-if)#ip address 172.17.0.1 255.255.0.0 Router(c on fig-if)#在D座楼中设置静态路由Routere nableRouter#c on figure termi nalEn ter con figurati on

14、comma nds, one per line. End with CNTL/Z.Router(config)#ip route 192.168.32.0 255.255.255.0 172.16.0.2Router(config)#ip route 192.168.33.0 255.255.255.0 172.16.0.2Router(config)#ip route 192.168.1.0 255.255.255.0 172.18.0.2Router(config)#ip route 192.168.4.0 255.255.255.0 172.17.0.2Router(config)#ip

15、 route 192.168.5.0 255.255.255.0 172.17.0.2 Router(c on fig)#路由器A座楼的配置：Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per line. End with CNTL/Z.Router(c on fig)# in terface FastEther net0/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet0/0, c

16、ha nged state to up %LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet0/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net1/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet1/0, cha nged state to up %LINEP

17、ROTO-5-UPDOWN: Line protocol on In terface FastEthernet1/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net4/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet4/0, cha nged state to up %LINEPROTO-5-UPDOWN: Line protoc

18、ol on In terface FastEthernet4/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0Router(c on fig-if)# no shutdow nRouter(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net0/0Router(config-if)#ip address 192.168.32.1 255.

19、255.255.0 Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net1/ORouter(config-if)#ip address 192.168.33.1 255.255.255.0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net4/0Router(config-if)#ip address 172.16.0.2 255.255.0.0Router

20、(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0Router(config-if)#ip address 192.168.31.1 255.255.255.0Router(c on fig-if)#在A座楼中设置静态路由Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per line. End with CNTL/Z.Router(config)#ip route 192.168.1.0 2

21、55.255.255.0 172.16.0.1Router(config)#ip route 192.168.4.0 255.255.255.0 172.16.0.1Router(config)#ip route 192.168.5.0 255.255.255.0 172.16.0.1 Router(c on fig)#路由器B座楼的配置：Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per line. End with CNTL/Z.Router(c on fig)# in ter

22、face FastEther net0/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet0/0, cha nged state to up %LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet0/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net5/0Route

23、r(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet5/0, cha nged state to up %LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet5/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial2/0Router(c on fig-if)# no shutdow nRouter(c

24、on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net0/0Router(config-if)#ip address 192.168.4.1 255.255.255.0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net5/0Router(config-if)#ip address 172.17.0.2 255.255.0.0Router(c on fig-if)#Router

25、(c on fig-if)#exitRouter(config)#interface Serial2/0Router(config-if)#ip address 192.168.3.1 255.255.255.0Router(c on fig-if)#在B座楼中设置静态路由Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per line. End with CNTL/Z.Router(config)#ip route 192.168.5.0 255.255.255.0 192.168.

26、3.2Router(config)#ip route 192.168.32.0 255.255.255.0 172.17.0.1Router(config)#ip route 192.168.33.0 255.255.255.0 172.17.0.1Router(config)#ip route 192.168.1.0 255.255.255.0 172.17.0.1Router(c on fig)#路由器Router 6的配置：Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per

27、line. End with CNTL/Z.Router(c on fig)# in terface FastEther net0/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet0/0, cha nged state to up %LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet0/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRout

28、er(config)#interface Serial2/0 Router(c on fig-if)#%LINK-5-CHANGED: In terface Serial2/0, cha nged state to upno shutdow nRouter(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net0/0Router(config-if)#ip address 192.168.5.1 255.255.255.0 Router(c on fig-if)#Router(c on fi

29、g-if)#exitRouter(config)#interface Serial2/0Router(co nfig-if)#ip address 192.168.3.2 255.255.255.0Router(c on fig-if)#在Router 6中设置静态路由Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per line. End with CNTL/Z.Router(config)#ip route 192.168.32.0 255.255.255.0 192.168.3

30、.1Router(config)#ip route 192.168.33.0 255.255.255.0 192.168.3.1Router(config)#ip route 192.168.1.0 255.255.255.0 192.168.3.1Router(config)#ip route 192.168.4.0 255.255.255.0 192.168.3.1 Router(c on fig)#路由器C座楼的配置：Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per lin

31、e. End with CNTL/Z.Router(c on fig)# in terface FastEther net1/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet1/0, cha nged state to upRouter(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0 Router(c on fig-if)#%LINK-5-CHANGED: In terface Serial3/0,

32、cha nged state to upno shutdow nRouter(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net1/0Router(config-if)#ip address 192.168.1.1 255.255.255.0Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0Router(config-if)#ip address 172.18.0.2 255.255

33、.0.0Router(c on fig-if)#%LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet1/0, cha nged state to upn o ip addressRouter(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net0/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet0/0, cha nged

34、state to upRouter(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0 Router(c on fig-if)#%LINK-5-CHANGED: In terface Serial3/0, cha nged state to admi nistratively dow nshutdow n Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net0/0Router(c on

35、 fig-if)#shutdow n%LINK-5-CHANGED: In terface FastEthernet0/0, cha nged state to admi nistratively dow n Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net1/0Router(c on fig-if)#shutdow n%LINK-5-CHANGED: In terface FastEthernet1/0, cha nged state to admi nistrativ

36、ely dow n %LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet1/0, chan ged state to dow n Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net5/0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net4/0Router(c on fig-if)#Ro

37、uter(c on fig-if)#exitRouter(config)#interface Serial3/0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net0/0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net1/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastE

38、thernet1/0, cha nged state to up %LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet1/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRouter(co nfig)#i nterface Serial3/0Router(c on fig-if)#%LINK-5-CHANGED: In terface Serial3/0, cha nged state to upno shutdow nRouter(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net1/0Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0Router(config-if)#ip address 172.18.0.2 255.255.0.0Router(c on fig-if)#