AtherosCalibration简介

1、atheros atheros calibration calibration 簡介簡介認識認識 atherosatheros 與與 art and iqviewart and iqview calibration calibration 關係關係n認識基本 art calibration utility 主要settings filen瞭解 art calibration utility 設備架構n認識 iqview 與 art calibration utility 兩者的差異性n瞭解 iqview calibration utility 設備架構n認識 mimo iqview calib

2、ration 主要settings filen實例說明認識認識 art calibration utility art calibration utility 主要主要settings filesettings file1.artsetup file2.calsetup file3.eep and ear file4.caltrgtpwr filewhat information can we get from the artsetupwhat information can we get from the artsetup file ?file ?1.log file settings2.s

3、sid settings3.from ssid to get eep file namewhat information can we get from the eepwhat information can we get from the eep file ? file ?1.get target power file name2.ssid3.device_type settings5.antenna settings 4.802.11a 11g 11b mode settingswhat information can we get from the caltrgtpwrwhat info

4、rmation can we get from the caltrgtpwr file ?file ?1.power settings 2.group settings what information can we get from the calsetupwhat information can we get from the calsetup file ?file ?1.mac id settings ( ap and router 產品不可寫入 ) 2.設備gpib address settings3.ppm and cable loss settings4.mask and per

5、and power limit settings5.rx sen spec settings6.calibration item settingsart calibration utility art calibration utility 設備架設設備架設認識 iqview 與 art calibration utility 的差異性1.除了基本的 artsetup、calsetup、eep、ear、caltrgtpwr file外,另增加iqsetup file2.iqsetup file 最主要設定. evm test channel settings per test channel

6、& spec settings 其他關於 iqview 量測上的設定iqviewiqview calibration utility calibration utility 設備架設設備架設認識認識 mimo iqview mimo iqview calibration calibration 主要主要settings filesettings file1.目前atheros mimo 產品 ip1006aa ( 11n mimo on board wireless router ) cb801an ( 11n mimo card bus )2.關於mimo calibration s

7、ettings file artsetup.txt eep file caltrgtpwr file iq_all(fail)_setup.txt iq_attn.txt iq_dut_mimo.txt iq_flow_mp.txt iq_meas_mimo_cb1071.txt iq_setup.txtwhat information can we get from the eepwhat information can we get from the eep file ? file ? 除了先前敘述的get target power file name、ssid、device_type、m

8、ode setup 、 antenna settings 外,須另注意tx rx chains settingswhat information can we get from the what information can we get from the iq_all(fail)_setup file ?iq_all(fail)_setup file ? log file settingswhat information can we get from the iq_attenwhat information can we get from the iq_atten file ?file

9、? cable loss settingswhat information can we get from the what information can we get from the iq_dut_mimo file ?iq_dut_mimo file ? tx power tolerance_up/lo settings ppm tolerance_up/lo settings evm spec settings per measurement settings rx sen spec settingswhat information can we get from the iq_fl

10、ow_mp what information can we get from the iq_flow_mp file ?file ? calibration item settingswhat information can we get from the what information can we get from the iq_measiq_meas_mimo_cb1071 file ?_mimo_cb1071 file ? enable debug settings interface_type ip settings mimo device configuration settin

11、gs calibration settings 其他關於 iqview 量測上的設定 ( per_packets settings ) ( tx power sweep settings ) ( per sweep settings ) ( evm measurement settings ) test utility version what information can we get from the iq_setup what information can we get from the iq_setup file ?file ? iqview ip address setting dut log control settings iq_flow_file settings iq_dut_file settings iq_product_id settings mac address is handled settings serial number is obtained settings failures are handled settings 實例說明與操作實例說明與操作 首先我們要先瞭解gui.exe 與 iq_ui.exe 兩者執行上的差異性 gui.exe 1.程式會先將所選擇的file name 資