双向可控硅tlc336a

1、TLC116 -> TLC386T/D/S/ASENSITIVE GATE TRIACSFEATURESVERY LOW Igt = 5mA max LOW Ih = 15mA maxDESCRIPTIONThe TLC116 -> TLC386 T/D/S/A triac family uses a high performanee glass passivated PNPN tech no logy.These parts are suitable for general purpose applications where gate high sensitivity is r

2、equired. Application on 4Q such as phase control and staticABSOLUTE RATINGS (limiting values)SymbolParameterValueUnitIT(RMS)RMS on-state current (360 conduction angle)Tl - 40 °C3ATa - 25 °C1.3(1)itsmNon repetitive surge peak on-state current (Tj initial - 25 °C )tp - 8.3 ms31.5Atp - 1

3、0 ms30I2tI2t valuetp - 10 ms4.5A2sdI/dtCritical rate of rise of on-state currentGate supply : Ig - 50mA diQ/dt - 0.1A/ sRepetitiveF - 50 Hz10A/阴NonRepetitive50Tstg TjStorage and operating junction temperature range-40 to + 150-40 to + 110°C°CTlMaximum lead temperature for soldering during

4、4 s at 4.5 mm from case230°CSymbolParameterTLCUnit116 T/D/S/A226 T/D/S/A336 T/D/S/A386 T/D/S/AVDRM VrrmRepetitive peak off-state voltageTj - 110 °C200400600700V2(1) With Cu surface 1cm .February 1999 Ed: 1A1/5TLC116 T/D/S/A -> TLC386 T/D/S/ATHERMAL RESISTANCESSymbolParameterValueUnitRth

5、 (j-a)Junction to ambient on printed circuit with Cu surface 1cm 250°C/WRth (j-l) DCJunction leads for DC20°C/WRth (j-l) ACJunction leads for 360 ° conduction angle ( F= 50 Hz)15°C/WGATE CHARACTERISTICS (maximum values)PG (AV) = 0.1W PGM = 2W (tp = 20 |1S)IGM = 1A (tp = 20 q)VGM

6、= 16V (tp = 20 阴).ELECTRICAL CHARACTERISTICSSymbolTest ConditionsQuadrantSuffixUnitTDSAIGTVD=12V(DC) RL=33 ?Tj=25°CI-II-IIIMAX551010mAIVMAX5101025VGTVD=12V(DC) RL=33 ?Tj=25°CI-II-III-IVMAX1.5VvgdVD=V drm RL=3.3k?Tj=110°CI-II-III-IVMIN0.2VtgtVd=V drm Ig = 40mA dIG/dt = 0.5A/ isTj=25

7、76;CI-II-III-IVTYP2ySIlIG= 1.2 IGTTj=25°CI-III-IVMAX15152525mAII15152525Ih *It= 100mA gate openTj=25°CMAX15152525mAVtm *Itm = 4A tp= 380 阴Tj=25°CMAX1.85VIDRMIRRMVDRM RatedVRRM RatedTj=25°CMAX0.01mATj=110°CMAX0.75dV/dt *LinearslopeuptoVd=67%V DRMgate openTj=110XTYP10102020V/

8、ys(dV/dt)c *(dI/dt)c = 1.3A/msTj=110°CTYP1155V/ ysFor either polarity of electrode A2 voltage with reference to electrode A1.ORDERING INFORMATIONPackageIT(RMS)VDRM /vrrmSensitivity SpecificationAVTDSATLC .63200XXXX400XXXX600XXXX700XXXX3/5TLC116 T/D/S/A -> TLC386 T/D/S/A#/5TLC116 T/D/S/A ->

9、; TLC386 T/D/S/AFig.1 : Maximum RMS power dissipation versus RMS on-state current (F=50Hz).(Curves are cut off by (dl/dt)c limitation)Fig.2 : Correlation between maximum RMS power dissipation and maximum allowable temperatures (Tamb and T|ead).#/5TLC116 T/D/S/A -> TLC386 T/D/S/A#/5TLC116 T/D/S/A

10、-> TLC386 T/D/S/AP (W)P (W)Tlead Cc)Fig.3 : RMS on-state current versus case temperature.T(RMa)fAjFig.4 : Thermal transient impedance junction to case and junction to ambient versus pulse duration.Zth -a (X/W)#/5TLC116 T/D/S/A -> TLC386 T/D/S/AFig.5 : Relative variation of gate trigger current

11、 and holding current versus junction temperature.Fig.7 : Non repetitive surge peak on-state current for a sinusoidal pulse with width : t <10ms, andcorresponding value of I2t.Fig.6 : Non Repetitive surge peak on-state current versus number of cycles.Fig.8 : On-state characteristics (maximum value

12、s).lT3M(Ah lIt(Aas)5/5TLC116 T/D/S/A -> TLC386 T/D/S/APACKAGE MECHANICAL DATATL PlasticREF.DIMENSIONSMillimetersInchesMin.Max.Min.Max.A9.5510.050.3750.396B7.558.050.2970.317C12.700.500D4.254.750.1670.187E1.251.750.0490.069F6.757.250.2660.285G4.500.177H2.043.040.800.120I0.750.850.0290.033#/5TLC116

13、 T/D/S/A -> TLC386 T/D/S/A#/5TLC116 T/D/S/A -> TLC386 T/D/S/AMarking : type numberWeight : 0.75 gInformation furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of pate

14、nts or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces a

15、ll information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.The ST logo is a registered trademark of STMicroelectronics? 1999 STMicroelectronics - Printed in Italy - All rights reserved.STMicroelectronics GROUP