加工中心精度检验规范

1、NO.日沛電腦配件（上海）有限公司RI PEI computer accessory (Shanghai) Co., Ltd.加工中心精度检验規範机型：MODEL机号：SERIAL NO.目录CATALOGUE1.0静态精度检查 6页PAGESTATIC ACCURACY INSPECION2.0定位精度检查 1页PAGEPOSITION ACCURACY INSPECTION3.0重复精度检查1页PAGEREPETITIONAL ACCURACY INSPECTION4.0循圓精度1页PAGEPALLET ACCURACY5.0 附件 .页 PAGEACCESSARY共页PAGE中國上海松江

2、區新橋鎮申港路 3636號No.3636 Shen gga ng Road,X in Qiao Son gjia ng Shan ghai China核准者CONFIRMED检验者CHECKED检验 日期DATEMCV F01S001Q301000003940331-71.0 静态精度 STATIC ACCURACY INSPECTION单位 Unit : mm测试方法图Measuri ng method diagramNO1.11.2检查项目In spect ion item床台X轴方向运动 之真直度a.Straight ness X-Zof the X 面内axismoveme nt床台丫

3、轴 方向运动 之真直度许可差Permissible deviati on实 际测量值Measured valueb.Y-Z面内a.Straight ness X-Zof the 丫 面内axismoveme ntb.Y-Z面内111a昌U L0.06/10000.06/10001-2单位 Unit : mm测试方法图Measuri ng method diagram检查项目In specti on itemNO床台x轴方向之- 运动与其上面之 平行度Parallelismbetwee n1.3 movement in Xaxis directi on and table upper surfa

4、ce1.4床台丫轴方向之运动与其上面之 平行度Parallelismbetwee n movement in 丫 axis directi on and table upper surfaceX轴方向运动与 床台基准沟侧面 之平行度Parallelism betwee n1.5 movement in Xaxis directi on andSide surface oftable refere nee slot许可差Permissible deviati onX 三 5000.02500v X 三 8000.025800v X 三 1250 0.031250V X 三 2000 0.04实

5、际测量值Measured value丫 三 5000.02500V 丫 三 8000.025800V 丫 三 1250 0.031250V 丫 三 2000 0.04每300mm的量测距离下许可差为0.015mm0.015for a measuri nglen gth of 3001-4单位 Unit : mm测试方法图Measuri ng method diagramNO1.61.7检查项目In specti on item各轴方向a.相互运动X-Y之直角度轴Perpe ndicuPlacelarityBetwee nmoveme ntin X axisdirecti onand Y axi

6、sb.directi onX-Zand Z axis轴directi onPlace许可差Permissibledeviatio n0.012/3000.012/300实 际测量值Measured valuec.Y-Z轴Place主轴中心线与床 台面之直角度Perpe ndicularitybetwee n cen terl ineof main spi ndleand table surface.0.012/300旋径每300Per3000.0151-6单位 Unit : mm测试方法图Measuri ng method diagram检查项目In specti on item许可差Perm

7、issible deviati onNO主轴孔内面之偏 摆Run out of spin die1.8 taper hole主轴轴线与Z轴 轴线运动间的平 行度Parallelism1.9 between thespin dle axis and the Z-axis moti on主轴在Z轴方向之移（松）动量Moveme nt of main1.10spindle in Z axisdirecti on主轴端面之偏摆Run out of mainspin dle outersurface1.11O=实 际测量值Measured value固定端At spin dle side end of

8、testbar0.005固定端300处At 300 position0.015a:0.015/300b:0.015/3000.0050.011-81.12主軸外面之偏擺i> k1Ji1Run out of mainspin dleouter0.01mmsurface1.13床檯X軸方向運 動之直線度the X axis.Straight ness of table moveme nt in0.01/3001. Apply a fixed indicator to the straight edge as the figure shown.2. Adjust to get reading

9、at both ends of the straight edge.2. Move the table 300 mm in X-axis direction.Record the largest value difference as the measurement value.the Y axisL J “1.14床檯丫軸方向運動之直線度Straight ness of table moveme nt in0.01/3001. Apply a fixed indicator to the straight edge as the figure shown.2. Adjust to get r

10、eading at both ends of the straight edge.2. Move the table 300 mm in X-axis direction.3. Record the largest value difference as the measurement value.1-51.151.16旋轉檯旋轉偏擺Table runo ut(Z)1.17車刀角度換刀後重複定位精度Repeatability of tool an gle after tool cha nge.1.18車刀角度停止後重複定位精度Repeatability of tool an gle after

11、 tool stop.0.005mm0.001mm0.001mm1.21主軸振動檢測Spin dle vibrati ondetecti on=0.6mm/s(Ref)2.0 定位精度检查 Positi oning accuracy in specti on单位 Unit : mm1-72.0 定位精度检查 Positi oning accuracy in specti on单位 Unit : mm项次NO检查项目In specti on item测试方法图Measuri ng method diagram许可差Permissible deviati on实 际测量值Measured valu

12、e1-#2.0 定位精度检查 Positi oning accuracy in specti on单位 Unit : mm2.1二 I-r 剧mA-i rL 三 10000.011000V L 三 20000.015L 三 20000.02直线运动之定位精度ISO230-2循环次数：X 2次Positi oning accuracy of straight li ne moveme ntBy Y ISO230-2Cycle times:Two times1-#2.0 定位精度检查 Positi oning accuracy in specti on单位 Unit : mm1-#2.0 定位精度

13、检查 Positi oning accuracy in specti on单位 Unit : mm单位 Un it: sec2.2回转运动之定位精度Positi oningaccuracyof straightli nemoveme ntByISO230-2Cycletimes:Twotimes15ff1-83.0 反复精度检查 Repetiti on accuracy in spect ion单位 Un it: sec项次NO检查项目In specti on item测试方法图Measuri ng method diagram许可差Permissible deviation实 际测量值Mea

14、sured value3.1直线运动之 反复定位精 度ISO230-2Positi oningrepeatabilityof straightli nemoveme ntByISO230-2Cycle times:Two times0.0063.2回转运动之 重复定位精 度ISO230-2 Positi oning repeatability of straight li ne moveme nt By ISO230-2Cycle times :Two timesC10811单位 Un it: sec1-103.0 反复精度检查 Repetiti on accuracy in spect ion单位 Un it: sec项次NO3.3检查项目In specti on itemMax reversal X value最大反沖值Positi on accuracy qualified toISO 230-2测试方法图Measuri ng method diagram4.0 循圓精度检查 Repetition accuracy inspection项次NO检查项目In specti on item测试方