节套入刀轴转动旋耕机

1、节套入刀轴转动旋耕机安装旋耕机时应先切断拖拉机动力输出轴动力，取下输出轴罩盖，倒车并挂接好旋耕机，然后将带有方轴的节装入旋耕机传动轴上，提起旋耕机，由于旋耕作业后碎土充分，地表平整，且减少作业工序，因而受到广大农户的欢迎。但使用方法是否得当、维护是否规范，对机器性能、效率发挥至关重要。因此，掌握正确的使用与日常维护方法十分必要。 Installation of rotary cultivator should first cut off the power output shaft of the tractor power output shaft cover, remove, reversi

2、ng and hanging good cultivator, universal joint transmission shaft and then loaded with square shaft, filed a cultivator, because the rotary tillage soil crushing after fully, surface is smooth, and reduce the operation steps, which is welcomed by the farmers welcome. But whether the method properly

3、, whether the norms play a crucial role in maintenance, machine performance, efficiency. Therefore, to master the correct use and maintenance method is very necessary.用手转动刀轴看其运转是否灵活，再将带方套的节套入拖拉机动力输出轴固定。安装时应注意：方轴和方轴套的叉形接头应在同一平面内，若装错，工作中节处会发出响声，旋耕机振动加大，并可损坏机件。还应注意方轴的长度，保证旋耕机在工作与提升时，方轴与方套及夹叉既不顶死又有足够的配合

4、长度。节装好后，应将安全插销对准花键轴上的凹槽插入，再用开口销锁定。 Hand rotating cutter shaft at the operation is flexible, then take the square sleeve joint is sheathed in the tractor power output shaft is fixed. Should pay attention to installation: fork joint square shaft and shaft sleeve should be in the same plane, if wrong,

5、at the joint work will sound, rotary vibration increase, and mechanical damage. Attention should be paid to party a shaft length, ensure the rotary cultivator in work and promotion, a square shaft and sleeve and the bracket is not top dead and with enough length. Universal joint is installed, should

6、 be the safety pin alignment groove spline shaft is inserted, then the cotter pin lock.1.3耕作前的调整 1.3 effects of tillage before adjustment（1）左、右水平的调整。将旋耕机降低，使刀尖接近地面，视其左右刀尖离地面高度是否一致；若不一致，则调节右悬挂杆的高度，使旋耕机刀尖离地高度一致，以保证左、右耕深一致。 (1) the left, the right to adjust the level of. The rotary tiller is reduced, s

7、o that the tip is close to the ground, as the tip height from the ground is consistent; if not, adjust the right suspension rod height, tiller height from the ground to the tip, to ensure that the left, right depth consistent.（2）前后水平的调整。将旋耕机降到要求耕深时，视其节夹角，调节拖拉机悬挂机构的上拉杆，使节近于水平，保证节及整个机组在有利条件下工作。 (2) be

8、fore and after the level adjustment. Rotary tillage machine to the required depth, depending on the Cardan angle, adjusting rod tractor suspension mechanism, the universal joint universal joint and nearly horizontal, ensure the unit work under favorable conditions.1.4使用时的调整 When using the 1.4 adjust

9、ment旋耕机的调整可在试耕时进行，也可在作业中根据具体情况随时调整。 Rotary adjustment can be carried out trial cultivation, but also in operation at any time to adjust according to the specific situation.（1）耕深调整。轮式拖拉机配用旋耕机的耕深，可用拖拉机液压耕深调节或旋耕机上的限位滑板控制（直接连接式的旋耕机，是用改变提升链条或拉杆的长度来控制）。 (1) depth adjustment. Wheeled tractor rotavator plow

10、ing depth, available tractor hydraulic rotary cultivator tillage or limiting slide control regulation (direct connection type rotary cultivator, is by changing the lifting chain or rod length to control).手扶拖拉机配用旋耕机的石英壁布耕深，是用尾轮或滑撬控制，若调整后仍达不到要求，可松开夹紧手柄，提升尾轮套管来增加耕深。 Walking tractor rotary cultivator ti

11、llage depth, with the tail wheel or skid control, if the adjustment is still not up to the requirements, can loosen the clamping handle, lifting the tail wheel sleeve to increase the depth.（2）碎土性能调整。碎土性能与拖拉机前进速度及刀轴转速有关。刀轴转速一定时，提高拖拉机的行驶速度，塑料土工格栅土块增大；反之则减小。改变平土拖板的高低位置，也影响碎土效果，使用时可根据需要，将平土拖板固定在某一位置上。 (

12、2) soil crushing performance tuning. Soil crushing performance and tractor speed shaft speed and tool for advancing. The knife shaft rotational speed, improve the tractor speed, soil increases; and vice versa. Changing a flat earth the height position, also affect the soil crushing effect, when used

13、 according to need, the flat earth plate fixed on a certain position.（3）水平调整。三点悬挂式旋耕机的左右水平调整，是通过悬挂机构右提升杆来调节；前后水平调整，是通过上拉杆调节，以保证耕深的一致性。 (3) the level adjustment. Three point suspension type rotary tiller level adjustment, is through the right lifting rod mechanism to adjust the level of suspension; b

14、efore and after the adjustment, is regulated by the draw rod, so as to guarantee the consistency of deep tillage.（4）提升高度调整。用节传动的旋耕机，因节的传动中的倾角不能大于30°，因而提升不能过高。一般只要使刀片离开地面1520cm即可；提升过高时，节方轴、套管及叉形接头会顶死，将扭坏节和动力输出轴，严重时将使拖拉机后桥壳体报废。使用中应将液压操纵手柄限制在允许的提升高度内。(4) the lifting height adjustment. With a rotary gimbal driving, because cannot drive gimbal angle of more than 30 degrees, thus increase can not be too high. General as long as the blade from the ground 15 20cm; the increase too high, cardan shaft, slee