s履带吊组装作业指导书

1、Good is good, but better carries it.精益求精，善益求善。s履带吊组装作业指导书CSPC NANHAI PETROCHEMICALS PROJECTCSPC NANHAI PETROCHEMICALS PROJECTCSPC 南 海 石 化 项 目THE ASSEMBLY OF CC1000 CRAWLER CRANECC1000履带吊组装作业指导书WORKING INSTRUCTION: WI-8710-8100-2012作业指导书：WI-8710-8100-2012SEPCO Electric Power Construction Corporation山

2、东电力基本建设总公司REV 版次DATE日期REASON OF ISSUE发布原因BY编制CHKD审核REVIEW审查APPR批准A26NOV 03ISSUED FOR REVIEWZJZFZXSDPB02DEC 03ISSUED FOR APPROVALZJZFZXSDP目 录TABLE OF CONTENTS1 PURPOSE目的 2 SCOPE范围 3 RESPONSIBILITIES职责 4 PROJECT SUMMARIZATION工程概述 5 WRITING REFERENCE编制依据 6 CONSTRUCTION PREPARATION施工准备7 THE CONSTRUCTING

3、 MACHINES AND TOOLS 施工机械及工器具8 ORGANISE LABOUR FORCE劳动力组织9 CONSTRUCING PROCESS AND METHOD 施工工序和施工方法10 THE PROTECTION MEASURE OF ENVIRONMENT境保护措施11 JOB SAFETY ANALYSIS安全工作分析1 PURPOSE目的 To provide the working instruction for the assembly of CC1000 crawler crane in CSPC Nanhai Petrochemicals Project, St

4、eam & Power Plant Project to ensure the project to complete on time and with good quality.在于制订南海石化汽电联产项目的CC1000的组装的作业指导，确保工程高质量的按期完工。2 SCOPE范围This instruction complies to the assembly of CC1000 crawler crane in CSPC Nanhai Petrochemicals Project, Steam &Power Plant Project 本指导书适用于南海石化汽电联产项目起

5、重机械CC1000履带吊的组装。3 RESPONSIBILITIES职责3.1 SEPCO2 is responsible for the assembly and adjusting of CC1000 crawler crane. SEPCO2负责CC1000履带吊的组装与调试。3.2 SEPCO is responsible for the interface coordination and acceptance.SEPCO 负责接口协调和质量验收。4 PROJECT SUMMIRUZITION 工程概况 As the project needs, CC1000 will be tra

6、nsported from Yunhe project to Huizhou to lift the boiler steel structures. According to the requirement of the project, the working rate is 48m+36m.因工程需要，CC1000由运河工地运至惠州工地，用于锅炉钢架的吊装，根据工程需要其作业工况为48m+36m塔式工况。5 REFERENCE编制依据1.1 Site condition施工现场条件1.2 The manual of CC1000 crawler craneCC1000履带吊使用说明书6

7、CONSTRUCTION PREPARATION施工准备6.1 Constrution location smooth and temper 施工现场平整夯实6.2 Good separate measure on the site现场作好隔离措施6.3 The construction machines and tools are available.施工机械及工器具准备到位 6.4 Make a good orginazation of construction personel作好人员的组织工作7 THE CONSTRUCTING MACHINES AND TOOLS 施工机械及工器具7

8、.1 Crawler crane QUY50A and crane 30tQUY50A履带吊和50t汽车吊各一台 7.2 Big hammer ,wrench and other common tools大锤、扳手及其他常用工具7.3 Steel wire，tach ect，should meet the requirement钢丝绳、卡扣等应符合使用要求7.4 Pulling rope enough准备好揽风绳数量8 ORGANISE LABOUR FORCE 劳动力组织Commpany principal：1 Technical principal：1 HSE：1 Rigger：3 Ele

9、ctrician：2 Overhauling personel：3 Operator ：3 Fitter：2公司负责人：1 技术负责人：1安全员：1 起重工：3电工：2 检修工：4操作工：3 安装工：29 CONSTRUCTING PROCESS AND METHOD 施工工序和施工方法9.1 The width of the assembly area is about 20m and length 100m, and there are should be no barriers. The working ground is smooth, and separated by guard-r

10、ope.组合场地宽度约20米，长度约100米，且无障碍物。该工作场地平整，用警戒绳隔离。9.2 Transport CCI000 to the assembly area. Use the QYU50A and 50t crane to unload it。将CCI000运至组装现场，用QUY50A和50t汽车吊将其卸下。9.2.1 The front adopts a 6 × 37 36.5 20m rope, whose broken force is P=85.6t, the steel wire rope rolled to 4 twists. It can bear the

11、 weight of 39t. QUY50A is the main arm 16m，whose rated load is 44.95t and working radius is 4m.85600×sin78.79×439000Safety factor：n= =6 = 8.3 3900044950Load ratio： K= ×100%=86.7%前头采用6×3736.520m绳扣一根，其破断拉力为：P=85.6t，钢丝绳绕成4股，其承重为39t。QUY50A为16米主臂工况，额定负荷为44.95t，作业半径为4米。85600×sin78

12、.79×439000其安全系数： n= =8.33900044950负荷率： K= ×100% =86.7%9.2.2 The front adopts two 6×3721.516m ropes, whose broken force is P=5.3t. The steel wire rope rolled to 8 twists. It can bear the weight of 17.5t.The rated load of crane is 22.9t，whose working radius is 4m.后边采用6×3721.516m绳扣2

13、根，其许用拉力为：P=3.3t，钢丝绳绕成8股，其承重为17.5t。汽车吊额定负荷为29.50t，作业半径为5m.17.5 8×sin75.52安全系数： n= =2.36t3.3t1750029500负荷率： k= ×100%=59.3%17.5 8×sin75.52Safety factor ：n= =2.36t3.3t1750029500Load ratio ： k= ×100%=59.3% 9.2.3 Unload and assembly the crawler by 50t crane,and the weight of crawler is

14、 23t, adopts a 6 × 37 36.5 20m rope,.The steel wire rope rolled to 4twists,so the safety factor of the steel wire rope is :n=85600×4/23=14.9用50t汽车吊将履带卸车并组装，履带重23t，起吊绳用6×3736.520m钢丝绳一根，4股起吊，则钢丝绳的安全系数为 :n=85600×4/23=14.9 50t crane adopts the main arm 10.4m, and limit the

15、radius 50t is 5m,whoserated load is 30t,then the load ratio of crane is:K=（23+0.56）/30=78.5%汽车吊采用10.4米主杆，半径控制在5米，其额定负荷为30t。则吊车负荷率为K=（23+0.56）/30=78.5%9.2.4 When use two cranes to lift at the same time, lift to leave ground about 10 cm and stop over 10 minutes. Check the condition of each part of fou

16、ndation machine. After sure nothing ，truck remonve stack up wood and put down the main machine. First assembly one crawler, then remove the wood when assembly the other，finally load equilibrator .两车同时抬吊时，抬离托盘约100mm，停留10分钟，检查地基机械的各部件状况，确认无问题后将拖车开走垫上道木，高度800mm，将主机放下。先穿上一条履带，然后穿另一条履带时将枕木撤去，并连接好四根斜撑杆，最后

17、根据说明书的要求装上配重。9.3 The assembly of the boom and rigging 臂杆、拉索的组装 6.3.1 Assembly the arm pole and rigging according to the relevant requirements of the manual. After they are assembled, connect moment limiter and the cable of height limiter，load the pull sensor in term of the request and pull on the ri

18、sing rope.按说明书的有关要求进行臂杆、拉索的组装，待其组合好后，按要求安装好拉力传感器，并穿好起升绳。 9.3.2 Use the assistant crane to lift the secondary arm。Raise the main arm about 10°. Adjust the top limiter and the lower limiter when pulling up the main arm，and the angel error can not be over 0.5°.Continue to pull up main arm aft

19、er adjusting the limiter，the top block of the assistant arm should roll down the ground to reduce the pulling moment. The top assistant arm dont leave the ground until the inclusion angle between the main arm and the ground isnt over 35°. 扳杆时用辅助吊车吊起副臂，将主杆扳起约10°时，调整副杆上、下限位，其角度误差不得大于0.5°

20、;。限位调整好后，继续扳起主杆，副杆头部滑轮应沿地面滚动，以减少扳起力矩，当主杆和地面夹角大于35°时，副杆头部方可离地。 9.3.3工况组装后的检查 Check after the assembly9.3.3.1 Whether the crane is placed on the level place.起重机是否放置在水平位置9.3.3.2 Whether the equilibrator meets the requirement.配重是否符合要求9.3.3.3 Whether the erection of the boom is correct.臂杆的安装是否正确 9.3

21、.3.4 Whether all the limiting switchs are installed correctly and work normally.所有的限位开关是否正确安装和全部正常9.3.3.5 Check the flexibility of the mechnization tiliting preventation support within the swing scope.扳起前，检查机械式防后倾支撑在整个摆动区域内动作是否灵活 9.3.3.6 Whether the system of the hydraulic pressure is natural.液压系统是否

22、正常9.3.3.7 Whether the pin connection is safe and reliable.所有的销连接是否安全可靠9.3.3.8 Whether the indication of the instrument is normal.仪表指示是否完全正常10 THE PROTECTION MEASURE OF ENVIRONMENT 环境保护措施10.1 Make the oil leakproof measure, place the spill kit on the connection of the oil pipe.作好防漏油措施，接油盘放在油管接口等处。10.

23、2 The spill kits are within the reach to avoid oil leaking to the ground.吸油棉放在随手可及的地方，以防油漏到地上。10.3 The Lubricating grease is the right mount，and not throw to ground. 加润滑油脂要适量，注意不要丢到地上。10.4 Place the rubbish and scrap to the designated place after operation is finished.工作完毕后,把垃圾废料放到指定的地点。11 安全工作分析 JO

24、B SAFETY ANALYSIS18publicity slogans slogan, distributed various publicity material more than 10,000 copies, answers past masses Advisory more than 500 more than passengers; Organization produced Ordinance training textbook more than 10,000 volumes, held Ordinance courses 36 period times, participat

25、e in training levels the sector leaders and administrative organ staff 12,000 passengers, for " Methods a case "project to create a good atmosphere. In addition, in May this year, entrust China University, was held in Beijing, the city's legal leaders ' "enhance the ability of

26、 administration by law and innovation of working mechanism of" training course, 6 legal experts were invited on theory of administration by law and the construction of Government governed by law, and administrative law enforcement . To conduct study tours and participated in the province's

27、Legislative Affairs Office held in Weifang's Government legislative business training courses across the province, appointed a responsible Deputy Director participated in legislative technical training courses organized by the national people's Congress in Beijing, to seriously study the the

28、ory of local legislation and the legislative technical specifications, laid the groundwork for next legislative work in our city. (B) expand the channels, innovative mechanisms to improve the credibility of the administrative review. 1-September cumulative cases 295, has handled 168. Following revie

29、w Institute administrative proceedings in the courts below the 20%, the administrative review decision to the Court of administrative proceedings, maintaining 100%. After the implementation of new administrative procedural law, the municipal government levels handled a total of 19 cases of respondin

30、g, appear in court more than 10 times, the prosecution case 1, reply 26 cases of administrative review, with the provincial government and make administrative review cases 8, method involved 20 leading contracting matters. No case of administrative reconsideration petitions or social instability, ef

31、fectively resolving a number of administrative disputes, improve the credibility of the administrative review. We are prominent in the work grabbed a reconsideration mechanism. Relative concentrated administrative reconsideration terms Hou, administrative reconsideration case sharply rose, for reduc

32、e administrative relative people of v tired, reflected administrative reconsideration "people, and reconsideration for people" of purposes, we opened has online accepted reconsideration application and reconsideration decided book online public platform, makes applicants at any time can on

33、line view application accepted and made decided book situation, and in city promotion "three Member a Center" administrative reconsideration work mode, better to achieved of social effect and work benefits of double harvest. Second, raise the case quality of administrative reconsideration.

34、 This year will continue to improve the quality of case as a breakthrough, strictly control the case of the mark, in addition to personal and State secrets will be tried publicly, especially wide social impact, legal relationships complex and serious cases on the merits shall be taken hearing and br

35、ainstorm ways to a trial, and enhanced transparency in the case, ensure the quality of the trials. Third, further strengthening the construction of Administrative Review Committee. On promoting the county people's Governments of the administrative review of the Committee's opinions on the st

36、andardization on the basis of strengthened on the standardizationWI-8710-8100-2012 REV.B Page 18 of 18CC1000履带吊组装作业指导书 JOB SAFETY ANALYSIS安全工作分析 Date(日期)：2003-11-26 Job Title工作名称:Assembly of CC1000CC1000履带吊的组装LOCATION地点 ： Construct Site 施工现场JSA No JSA编号: JSA-8560-8102-0066 DPARTMENT（部门）：SEPCO2 Mecha

37、nizationCompany机械公司SUPERVISOR主管人 ：TITLE OF PERSON WHO DOES JOB工作执行人职务:PREPARED BY 编制： REVIEWED BY 审查: APPROVED BY 批准：Environmental Conditions环境条件Inside内部 Outside 外部 Cold 冷 Heat 热 Wet 湿 Dust灰尘 Vapors/Mist 水汽 Noise 噪音 Vibration 震动 other其他 Heavy Rain 大雨 Primary Job Functions & Position 基本工作行动Liftin

38、g 举重 Grasping 抓取 Pushing 推 Sitting 座 Reaching 延伸 Bending 弯曲 Kneeling跪 Standing 直立 Pulling 拖 Squatting 蹲 Other 其它SEQUENCE OF BASIC JOB STEPS工作步骤POTENTIAL HAZARD潜在危险风险评估RAM （H 、M、L）RECOMMENDED ACTION OR PROCEDURE 控制行动措施ACTION BY 执行人DATE DUE完成日期REMARK备注Car transporatation汽车运输Car transportation汽车运输The v

39、ehicle moves to harm the person车辆移动伤人L1 Follow relevant regulation during transportation.运输中必须遵守有关规定。2.Entering the construction area must reduce speed进入施工区域要减速慢行。Limited by damaged and overturning object毁坏或倾翻物体而受限 L1The transportation equipment must sealed firmly.运输设备必须封车牢固。2The vehicle condition i

40、s good.运输车辆车况良好。The falling objects damage the person 落物伤人 LWear personal PPE entering the construction spot.进入现场必须配戴好个人防护用品。Support the crane起重机支车Damage by vehicle moving机械移动伤人LPlace the crane horizontally and set up special zone. Authorized person enter only.起重机水平放置，且设立专门区域，无关人员不得进入。limited by dam

41、aged or overturned object毁坏或倾翻物体而受限 L 1Select correct position to support the crane, and make sure that the crane doesnt overload when unloading.正确选择起重机支车位置，保证卸车时吊车不超负荷。2 No trench is under the crane. The foundation must be firm and block up legs. 起重机支车下方不得有管沟等，地基必须坚实，且应垫好支腿。 Hang up the sling 栓起吊绳H

42、ang up the sling栓起吊绳Injured whist lifting or carrying .举起或搬运受伤LThe constructing personnel must wearthe PPE correctly施工人员穿好个人防护用品。Striking against solid object固定物体打击 L1 Sling, clamping ring, etc. cant be threw randomly.吊绳、卡环等不能抛掷。2Make the good protective measure to prevent the sling from damaging.作好

43、防护措施，以防吊绳受损。3 The slings cant huddle each other.起吊绳不能压绳Injured by fall to the ground地面跌倒伤害 L1Dont stand on the sling when hang it.拴起吊绳时不得站在起吊绳上。2 Concentrate when working作业时要精力集中。 Unload the mainframe卸主机Damaged by moving objects移动物体伤人 M1Monitor during lifting to prevent hit on person or other object

44、s.吊运过程中，作好监护工作，以防碰到人或其他物体。2 Dont stand under the lifted object and the boom.吊物及臂杆下方不得站人。3 The directive sigal must be clear, and the operator operates strictly according to the signal.指挥人员信号清晰，操作人员严格按指挥人员发出的信号进行操作。Unload the mainframe卸主机Limited by damaged or overturned object毁坏或倾翻物体而受限 M1 Monitor th

45、e display of the moment limiter when operating. 操作时监视力矩限制器显示器2 No striking work in the process of operation.运行过程中不能有冲击作业3 Cooperate closely when two cranes uplift , and the load of one crane cant increase suddenly.两车抬吊时，要密切配合，不能出现一车负荷突然增加的现象4 Monitor the foundation well作好地基的监护工作Injured by fall on th

46、e ground地面跌倒伤害Mconcentrate when working 施工作业时要精力集中Fall of person from height 高空坠落MFasten the safety belt correctly overhead.高空作业要系好安全带 Assembly 组装 Assembly组装Assembly组装Striking against or struck by moving object移动物体打击 MThe directive signal must be clear, and the operator operates strictly according t

47、o the signal.指挥人员信号清晰，操作人员严格按指挥人员发出的信号进行操作。Injured whist lifting or carrying .举起或搬运受伤MConcentrate when working, avoid damage by crush and push.工作人员应精力集中，注意挤伤或砸伤。Limited by damaged or overturned object毁坏或倾翻物体受限 M1Block up the sleeper under the arm poleto avoid damaging it.杆臂下方应垫上枕木，以免碰伤杆臂。2Cotter pin

48、 should be fixed firmly. 开口销等应安装紧固。Fall of person from height 高空坠落MFasten the safety belt correctly overhead.高处作业系好安全带Exposure to or contact with harmful substance 接触或揭漏有害物M1 Place the spill kit on theconnectionof the oil pipe.作好防漏油措施，接油盘放在油管接口等处。2 The spill kits are within the reach to avoid oil le

49、aking to the ground.吸油棉放在随手可及的地方，以防油漏到地上。3 The Lubricating grease is the right mount，and not throw to ground. 加润滑油脂要适量，禁止丢到地上。4 Place the rubbish and scrap to the designated place after operation is finished.工作完毕后,把垃圾废料放到指定的地点。Pick off hook摘钩Injured by fall to the ground地面跌倒伤害L1 1 Select the smooth and clear ground as the place of picking off hook. 选择平整、干净的场地做为摘钩场地。2 The slings pile after picking off hook. 摘钩后钢丝绳。Injured whist lifting or carrying .举起或搬运受伤L1 The height of hook can not