(完整版)插补法的例题及答案

1、设定的加工轨迹为第一象限的直线OP,起点为坐标原点，终点坐标A（x,y ），其值为（6,4），试进行插补计算，作出轨迹图，与进给 ee过程。插补过程：序号偏差判别进给偏差计算终点判别0F 二 00n = 10 xy1F 二 o0+ AxF = F - y =_410en =9xy2F 02+ AxF = F -y =-232en =7xy4F 04+ AxF = F - y =054en =5xy6F 二 05+ AxF = F - y =-465en =4xy7F 07+ AxF = F -y =-287en =2xy9F 09+ AxF = F - y =0109en =0 xy利用逐点比

2、较法插补圆弧PQ,起点P (8,0)终点Q(0, 8),试写出插补过程及轨迹序号偏差判别进给偏差计算终点判别0F 二 0, x =8, y =00n =16xy1F 二 o0_ AxF = F -2x +1=-15,x =7, y =01 0n =15xy2F =-1501+ AyF = F +2 y +1=-14, x =7, y =0+1=12 1n =14xy3F =-1402+ AyF = F +2 y +1=-11, x =7, y =1 + 1=232n =13xy4F =-1103+ AyF = F +2 y +1=-6, x =7, y =343n =12xy5F =-605_

3、 AxF = F -2 x +1=-12, x =6, y =465n =10 xy7F =-1206+ AyF = F +2 y +1=-3, x =6 y =576n =9xy8F =-308_ AxF = F -2 x +1=-3 , x =5 y =698n =7xy10F =-3010_ AxF = F -2 x +1 = 1 , x =4 y =711 10n =5xy12F =1011_ AxF = F -2 x +1=-6 , x =3 y =712 11n =4xy13F =-6013_ AxF = F -2 x +1=4 , x =2 y =81413n =2xy15F =

4、4014_ AxF = F -2 x +1 = 1 , x =1 y =81514n =1xy16F =1015_ AxF = F -2 x +1=0 , x =0 y =81615n =0 xy假设加工第一象限逆圆弧AB,起点A的坐标为X = 0,y = 4,终点B 00的坐标值为X = 0,y = 4。试进行插补计算，作出轨迹图及插补过程。ee序号偏差判别进给偏差计算终点判别0F 二 0 , x =4,y =00n =8xy1F 二 o0_ AxF = F -2 x +l=-7, x =3, y =01 0n =7xy2F =-701+ AyF = F +2 y +1=-6, x =3,2 1y =0+1 = 1n =6xy3F =-602+ AyF = F +2 y +1=-3, x =3,32y =1 + 1=2n =5xy4F =-304_ AxF = F -2x+1=-3, x =2 y =354n =3xy6F =306_ AxF = F -2 x +