粗研磨机等设备中英文对照#严选优质

1、3.1.1.3.20 粗研磨机 主要目的 完成如下工作: 研磨各种机床 (铣刀，钻头); 研磨钳工工具 (剪刀，凿子); 制锁 (去毛刺，倒角.); 抛光.基本技术参数 砂轮 - 40050203 mm 精度等级N 刀具推荐高度, mm 6.100 钻头直径, mm 6.60 钻头顶角, 700.1400 间隙, 可达 200 旋转角, +200.-10 接触辊直径, mm 400 研磨带宽度, mm 80 研磨带长度, mm 3000 研磨带拉力 N 1000 砂轮最大直径, mm 400 砂轮最大高度, mm 55 砂轮孔直径, mm 50 新砂轮研磨速度, m/s 30 砂轮主轴端 (直

2、径/长度), mm 40/40 主轴中心线到机器操作台距离, mm 900 主轴旋转速度, rpm 1440 电压, V/F频率, Hz 380/50 规格, kW 4,0 外廓尺寸, mm 10006801230 重量, kg 358General Technical Characteristics Abrasive wheels - 40050203 mm Accuracy class N Recommended height of cutters, mm 6.100 Diameter of drillbits, mm 6.60 Drillbit point angle, 700.1400

3、 Clearance, up to 200 Angle of rotation, +200.-10 Diameter of contact roller, mm 400 Width of grinding belt, mm 80 Length of grinding belt, mm 3000 Tension of grinding belt, N 1000 Maximum diameter of abrasive wheel, mm 400 Maximum height of abrasive wheel, mm 55 Diameter of hole of abrasive wheel,

4、mm 50 Grinding speed with new grinding wheel, m/s 30 End of grinding spindle (diameter/length), mm 40/40 Distance from machine stand to spindle center line, mm 900 Rotational speed of spindle, rpm 1440 Voltage, V/Frequency, Hz 380/50 Capacity, kW 4,0 Overall dimensions, mm 10006801230 Weight, kg 358

5、3.1.2.3.1 调整和移交自动机车信号方案到质监部门的设备概述设备设计用于及时监测机车部件的故障信号（()），解码机车司机的警觉性控制装置的设备及模块()。控制台用于检测放大器（25/30）和解码器（-1）和“机车司机警觉控制装置”模块（）（PDU）-67型。结构上，控制台应设计成一个带接触板的垂直面板的台面，并应通过连接插头与控制台连接，并可在台面上自用移动。技术参数说明供电电源 U=220 V 整流电压U=50 V 可调 40-60 V 轨道测试段25,50,75 Hz电信号的发送，并带编码组合的生成及自动或手动组合的可能性。3.1.2.3.1 Device for adjusting

6、 and handing over of Automatic Locomotive Signaling scheme to quality control department General Information: Device is designed for timely detection of failures in components of Automatic Locomotive Signaling (), decoding device and block of locomotive driver alertness control device (). Console fo

7、r testing of amplifier (25/30) and decoding device (-1) and block of locomotive driver alertness control device () of (PDU)-67 type. Structurally, console shall be designed as a desk with vertical panel with contact cardboards and shall be connected with the console by means of connecting plugs and

8、shall freely move on the desk. Technical Characteristics: Power supply U=220 V Rectification of voltage U=50 V Shall be adjusted 40-60 V Sending of electrical signals to rails of tested section 25,50,75 Hz with the producing of coding combinations with the possibility of automatic or manual change o

9、f combinations.3.1.2.3.12 轮对辊锻压力机 概述该压力机的目的是对电力和柴油机车轮面进行辊锻加工技术参数说明最大压力80吨3.1.2.3.12 Wheel set Tread Roll-forging Press. General Information: The purpose of the press is to roll-forge wheel treads of electric and diesel locomotives. Technical Characteristics: Maximum force 80 ton-force3.1.2.3.13 颈部滚压

10、机技术参数中心高度, mm . 320 中心间距 mm . 2700 颈部加工直径, mm . 90 和 240 变速箱齿轮数, pcs . 6 每分钟转数 . 58; 78; 120; 160; 216; 335 切割块数量（双), 个 . 2 线进给范围, mm/min . 56; 78; 115; 162 切割块移动速度, m/min . 2,6 主驱动电机规格, kW . 11 机器尺寸, mm; 长 . 5085 宽 . 2900 高 . 13653.1.2.3.13 Neck rolling machine Technical Characteristics Height of c

11、enters, mm . 320 Distance between centers, mm . 2700 Diameters of processed neck, mm . 90 and 240 Number of gears of change gearbox, pcs . 6 Rounds per minute . 58; 78; 120; 160; 216; 335 Number of cutter blocks (double), pc . 2 Range of line feed, mm/min . 56; 78; 115; 162 Value of quick motion of

12、cutter block, m/min . 2,6 Main drive electric engine capacity, kW . 11 Machine dimensions, mm; Length . 5085 Width . 2900 Height . 13653.1.2.3.14 高频单元概述这一单元的目的是硬化VL60k, VL80s和Ozbekiston 电力机车弹性钝齿轮的齿牙行数。技术参数说明这是具有一个带有供水、动力电缆和硬化钝齿轮的高频电感的旋转平台，高频发生器的频率是2.510KGz，规格是 100KW。3.1.2.3.14 High Frequency Unit Ge

13、neral Information: The purpose of the unit to harden teeth rows of elastic cogwheel of VL60k, VL80s and Ozbekiston electric locomotive.Technical Characteristics: It represents a rotary stand with water feed and power cable, HF inductor for hardening of cogwheel and HF generator having frequency of 2

14、.5-10KGz and capacity of 100KW3.1.2.3.24牵引发动机风扇检测平台 技术参数说明几个电机的协调控制，通过他机械（通过轴连接）和电气（发电机）彼此连接，并具有从一个到数个的控制回路。复杂操作过程中的程序控制。可控制如下几项：直流驱动电机（稳压整流器），或交流驱动电机（单个转换器）电子调节器（包括电流、电压、频率、每分钟转数、温度、压力、照明等）的设计基于任何方案（稳压整流器、逆变器、断路器、助力器、回扫等），和任何元件基础（晶体管、晶闸管、MOSFET, IGBT 等。同步电机、压缩机组、充电设备、电镀设备、UPS等的旋转和控制系统接触开关单元（继电器、启动开

15、关等）和接触元件（电子开关等）稳压功能执行系统（电驱动阀、电控电阻单元、电磁线圈、电磁阀和接头等）工作操作控制，结合在同一循环中（包括输送带、冷却设备、石油和化学工业设备、气体工业锅炉等）技术厂房的控制（总）包括大量输入因素、程序处理的信息在下列情况下，设备是专为室内操作：设备安装，海拔高度不超过1000m气候的版本和类别位置，根据GOST15150-69标准环境温度为0度到35度相对空气湿度不超过80% 在+25度条件下环境不会引起爆炸，粉尘等级不超过1 mg/m 大气类型（工业区域大气）决定的腐蚀性元素依据GOST 15150-69 关于外部环境M1的机械性因素的操作环境，依据GOST 1

16、7516-90. 技术参数说明供电网380 (220, 230, 240, 400,415, 660) V 50Hz, 220 (380, 440) V 60Hz 相位数：3执行功能：控制信号反馈的接收和生成任务分配生成数字和数字 - 模拟调节电源模块控制过程的传送模拟和逻辑控制信号的接收和处理继电器和电控原件控制过程的传送信息处理类型软件处理。根据雇主的要求，软件在特定项目的设计准备期间开发。基本元件，可编程微控制器为美国AMTEL的AVR系列RISC负载架构FLASH ROM程序的电子可变只读存储器，可重新编程达10000次，数据存储器EEPROM重新编程次数可达达10万次。32内部寄存器

17、内置硬件外围设备三插头可兼容子系列微型AVR，用于小型设备（complicity ）常规AVR，用中型设备大型AVR，用于较高设备3.1.2.3.24 Engine-fan of the stand for testing traction engines. Technical Characteristics. Coordinated control of several electrical machines, connected to each other both b mechanically (through shaft) and electrically (system engine

18、-generator) and having from one to several control loops. Program controlling of the sophisticated operation process, where controlled members include the following: Electric drive for engines of direct current (regulated rectifier) or engines of alternating current (individual convertor). Electroni

19、c regulators (of current, voltage, frequency, rounds per minute, temperature, pressure, lighting, etc) designed based on any scheme (regulated rectifier, inverter, chopper, booster, fly-back, etc) and on any element base (transistors, thyristors, MOSFET, IGBT , etc. Spinning and control systems for

20、synchronous electric engines, compressor units, charging devices, galvanic equipment, UPS, etc.) Contact switching units (relays, starter switches, etc.) and contact-free (electronic switches) Systems performing regulation functions (electrically driven valves, electrically controlled resistance uni

21、ts, magnet coils, electromagnetic valves and taps, etc.) Control of working operations, combined in one cycle (conveyor, cooling plants, equipment for oil and chemistry industry and gas industry boilers, etc) Control of one technological plant (aggregate) including large number of input factors, inf

22、ormation from which has to be processed by the program. Devices are designed for indoor operation under the following conditions: Altitude of plant installation, not more 1000 m Climatic version and category of location according to standard GOST 15150-69. Ambient temperature from 10 to 350 Relative

23、 air humidity not more 80% under +250 Environment not explosive, dust level not more 1 mg/m, corrosion active elements by type of atmosphere (atmosphere of industrial areas) according to GOST 15150-69 Group of operation conditions with regard to mechanical factor of external environment 1 according

24、to GOST 17516-90. Technical Characteristics: Power supply network 380 (220, 230, 240, 400,415, 660) V 50Hz, 220 (380, 440) V 60Hz Number of phases: 3 Performed functions: Receipt and generation of feedback control signals. Generation of assignment. Digital or digit-analog regulation. Delivery of con

25、trol action to power blocks. Receipt and processing of analog and logic control signals. Delivery of control action to relay and power control elements. Type of processing of information software processing. Software is developed during preparation of the design for specific project according to ter

26、ms of reference received from the employer. Base element programmable microcontroller of series AVR of the firm AMTEL Corporation (USA) RISC load architecture. Electrically alterable read-only memory of the programs FLASH ROM with the possibility of re-programming for up to 10,000 times and data mem

27、ory: EEPROM the possibility of re-programming for up to 100,000 times. 32 internal registers Built-in hardware peripherals Three plug-compatible subfamilies: tiny AVR for equipment of minor complicity. Classic AVR for equipment of medium complicity mega AVR for equipment of high complicity 3.1.2.3.3

28、0 喷丸室概述喷丸室用于对VL60k, VL80s 和 Ozbekiston电力机车变压器的活动部分、牵引电机和辅助电器进行喷丸，用于去除牵引电机和电枢以及发电机及辅助及其在机务段维修时，表面的粉尘。技术参数说明额定电压, kW, 5,5 外廓尺寸, mm, : 长 5220 宽 2900 高 2300 重量, kg, 1500 主电源电压, V 380 主电源频率, Hz 50 车辆规格, kgf, 90003.1.2.3.30 Blasting Chamber General Information: Blasting chamber for blasting of active part

29、 of transformers of electric locomotives series VL60k, VL80s and Ozbekiston, traction motors and auxiliary electrical machines designed to remove dust from the surface of traction motor frame and armature or the surface of generator and auxiliary machines, at the time of repair in depots. Technical

30、Characteristics: Rated voltage, kW, 5,5 Overall dimensions, mm, : length 5220 width 2900 height 2300 Weight, kg, 1500 Voltage of supply mains, V 380 Frequency of the supply mains, Hz 50 Truck capacity, kgf, 90003.1.2.3.39 同步发电机 技术特性：指示器: GS,250-20/4 功率：kW (kWA): 20 (25) 电压： V: 230 or 400 定子电流： : 63

31、or 36 电流频率： Hz : 50 转速： 转/分钟: 1500 功率比: 0,8 带中性点的星相连接3.1.2.3.39 Synchronous generator. Technical Characteristics: Indicators: GS,250-20/4 Power, kW (kWA): 20 (25) Voltage, V: 230 or 400 Stator current, : 63 or 36 Current frequency, Hz : 50 Rotation speed, rounds per minute: 1500 Power ratio: 0,8 Con

32、nection of phases star-connection with accessible neutral point3.1.2.3.43 张紧器总体说明：张紧器用于VL60k 和Ozbekiston系列电气机车变压器主变部份绕线的张紧。3.1.2.3.43 Tensioning device for the machine General Information: Tensioning device is designed for tensioning of the wire (bonding conductor) during winding of active part of t

33、ransformers of electric locomotives series VL60k, VL80s and Ozbekiston.3.1.2.3.44 用于密封和开封接线头的大电流强度的装置 N 3 kW U -220V.3.1.2.3.44 High-amperage device for sealing and sealing-off lead wires N 3 kW U -220V. 3.1.2.3.45配有平台的电剪刀 最大电压 24 V.3.1.2.3.45 Electric clippers with the stand up to 24 V. 3.1.2.3.46

34、线圈质量测定平台，匝间短路测试，U回路电流100,150,500 V3.1.2.3.46 Stand for determination of quality of coils and testing for turn-to-turn short circuits U current 100,150,500 V. 3.1.2.3.51 电感分流器测量装置N 0,6 kVA U -220 V 3.1.2.3.51 Device for measuring inductance of shunts N 0,6 kVA U -220 V 3.1.2.3.53 配备设备的喷砂柜总体说明：喷砂柜按照NA

35、AYKENS进行生成的清洁柜体，由喷砂柜子和喷雾柜子组成。需要提供两个工作平台，2个清洁器的过滤器，柜子的配件等。Technical Characteristics: 喷砂柜： : 长 28,000 mm 宽 7,000 mm 高 6,000 mm 喷抛清理和干燥柜: 长 28,000 mm 深 6,500 mm 高 7,100 mm 喷雾 0 - +21 当外部环境 -10 干燥 (+20+80)03.1.2.3.53 Shotblast cabinet with equipment General Information: Shotblast cabinet for cleaning of

36、 bodies produced by NAAYKENS. Consists of shotplast and spray pain cabinets. Supply 2 working platforms, 2 filters and filters for cleaner, parts for cabinet and spare parts. Technical Characteristics: Shotblast cabinet: length 28,000 mm width 7,000 mm height 6,000 mm Blast cleaning and drying cabin

37、et: length 28,000 mm depth 6,500 mm height 7,100 mm of spray 0 - +21 when outside temperature is -10 of drying (+20+80)03.1.2.3.63 EL交换机的试验台 ShR/-1. 1000850800mm. ShR/-1交换机技术要求: 该交换机用于是接收和分配电源，单相和多相网络过载和短路保护线路。额定电压: 380/220 V; 50Gz. 额定电流: 63 . 保护率IP40.安装类型：安装入口自动开关的开关能力: 4.5 kA.输入自动群集开关的开关能力4.5 kA结构

38、：热量自适应塑料整体尺寸：mm 20030595重量： 2.2kg3.1.2.3.63 Testing Stand for EL Switchboard ShR/-1. 1000850800mm. Technical Specifications of ShR/-1 Switchboard: The purpose of the switchboard is to receive and distribute power, protect lines from overloads and short circuits in single-phase and multi-phase networ

39、ks. Rated voltage: 380/220 V; 50Gz. Rated switchboard current: 63 . Protection rating: IP40. Type of installation: mounted. Switching capacity of inlet automatic switch: 4.5 kA. Switching capacity of input automatic cluster switch: 4.5 kA. Construction: self-extinguishing thermal plastic. Overall di

40、mensions (LxWxH), mm: 20030595. Weight: 2.2kg.3.1.2.3.85 换向片汇编工具NB418和NB514牵引电机的换向片的装配工具被设计来形成换向片与云母段上的径向表面螺栓连接的固定安装。3.1.2.3.85 Commutator Bar Assembler Tool Tool for assembling commutator bars of NB418 and NB514 traction motors is designed to perform firm installation of commutator bars with mica s

41、egments on radial surface with subsequent bolting.3.1.2.3.86 炉，用于加热和取出线圈外层绝缘该炉的设计应以保证可变的加热温度高达500C。整体内部尺寸应至少100010001000 mm。3.1.2.3.86 Furnace for Heating and Removal of Coil Housing Insulation The furnace shall be designed to ensure variable heating temperature up to 500 . Overall internal dimensio

42、ns shall be at least 100010001000 mm.3.1.2.3.88 牵引电机电枢线圈生产线14个工位和三线。概述：生产线被设计用于制造电力机车的完整的电枢线圈，并涵盖所有进程的开始线切割，塑形和电枢线圈绝缘。3.1.2.3.88 Traction Motor Armature Coil Fabrication Line 14 working positions and three lines. General Information: Fabrication line is designed to fabricate complete armature coils

43、for Ozbekiston, VL80s and VL60k electric locomotives, and covers all processes beginning with wire cutting, through shaping and to armature coil insulation.3.1.2.3.89 磁极线圈组生产线，用于牵引电机外壳10个工位和三线。概述：生产线被设计用于制造完整的电力机车牵引电机的极线圈，并涵盖所有进程的开始线切割，塑形和磁极线圈绝缘。3.1.2.3.89 Pole Coil Section Fabrication Line for Hous

44、ing of Traction Motors of Ozbekiston, VL80s and VL60k ELs. 10 working positions and three lines. General Information: Fabrication line is designed to fabricate complete pole coils for traction motors of Ozbekiston, VL80s and VL60k electric locomotives, and covers all processes beginning with wire cu

45、tting, through shaping and to pole coil insulation.3.1.2.3.92 轮面辊锻压机吨位80吨。 N =3千瓦。 372023102400mm。3.1.2.3.92 Tread Roll-forging Press Tonnage 80 ton. N=3kW. 372023102400mm3.1.2.3.93 电力机车轮对的平衡设备概述：该机器的目的是用于电力机车的轮平衡测量，不平衡量和角度测量值从30到3000公斤。死端绝缘体NSPKp120-25/1.2（120-25 /1,2）。技术规格：平衡转子重量范围，kg 100-10000最大转

46、子直径，mm 2500转子轴颈直径，mm 50-300转子中心之间的距离，mm min/max 500-46最小可达剩余不平衡，.mm/kg 0.4转子旋转速度，rpm 200-1000驱动器类型 变频异步驱动电机容量，kw 30.0站立长度，mm 50003.1.2.3.93 Balancing Machine for Wheelpairs of Ozbekiston ELs General Information: The purpose of the machine to perform balancing of electric locomotive wheelpairs to mea

47、sure values of disbalance and angles from 30 to 3000kg. Dead-end insulator NSPKp120-25/1.2 (120-25/1,2). Technical Specifications: Weight range of balanced rotors, kg 100-10000 Maximum rotor diameter, mm 2500 Diameter of rotor journal, mm 50-300 Distance between centers of rotor journals, mm min/max

48、 500-46 Minimum achievable residual unbalance, .mm./kg 0.4 Rotor rotational speed, rpm 200-1000 Type of drive Variable frequency asynchronous drive Motor capacity, kW 30.0 Length of stand, mm 50003.1.2.3.94 轮对轮面的应力削减该机器的目的是用于轮对的应力削减。输出容量 10010KW工作频率 100.5 KGZ工作电压 40020 V工作电流 2403.1.2.3.94 SHF for Stress Relieving of Wheel-Pair Tread The purpose of the machine is to stress relieve wheel-pairs. Output capacity 10010 kW Operating frequency 100.5 kGz Operating voltage 40020 V Operating cu