(中英文)检具设计方案.ppt

1、7/9/2020,a,1,B515 Checking Fixture Phase II Huangyan,Date 15-10-11,B515 检具-黄岩,7/9/2020,a,2,Swivel form check template min two numbers Provided,至少应有两个样板刀,7/9/2020,a,3,Max line 3mm from nominal line,Min line should be “Tolerance specified in cad”,Part,Nominal line,Trim line marking for all checking fi

2、xture,名义修边线,板件,距离名义修边线3mm的最大修边线,最小修边线的公差应符合图纸的要求。,所有检具划修边线,7/9/2020,a,4,A,B,A- You provided diamond pin it is not acceptable please provide tapper pin with minimum and maximum tolerance B- You provided straight pin instead of that please provide tapper pin with minimum and maximum tolerance as shown

3、 in the figure,Max tolerance,Min tolerance,Part,Round pin,最小公差,板件,最大公差,圆销,1.你方采用菱形销，是不可以的，请采用锥形销，并给出最大和最小公差。 2.不要采用直销，请采用锥形销，并给出最大和最小公差。,7/9/2020,a,5,Part No 8V21-A18A344,Up date the changes and sent me the updated data then Please Go for manufacturing,Provide car line with150mm pitch, part clamping

4、 as per LD data,Provide Swivel form check template min two numbers. See slide NO 2,至少应有两个样板刀。参照图片2,应有汽车坐标，并以150mm 为间距，零件夹持应符合零件检测的要求。,将修改后的设计发送给我们，然后进行制造。,7/9/2020,a,6,Part No CN15- N40308,Up date the changes and sent me the updated data then Please Go for manufacturing,Provide car line with150mm pi

5、tch, part clamping as per LD data,Provide Swivel form check template min two numbers. See slide no 2,将修改后的设计发送给我们，然后进行制造。,至少应有两个样板刀。参照图片2,应有汽车坐标，并以150mm 为间距，零件夹持应符合零件检测的要求。,7/9/2020,a,7,Part No CN15-N40324-A,Up date the changes and sent me the updated data then Please Go for manufacturing,Provide ca

6、r line with150 mm pitch,Provide Swivel form check template min two numbers. See slide no 2,至少应有两个样板刀。参照图片2,应有汽车坐标，并以150mm 为间距 。,将修改后的设计发送给我们，然后进行制造。,7/9/2020,a,8,This land should be increased by 3 mm so that,This land should be increased by 3 mm so that variation in burring (Flange) can be measured,

7、该区域高度加高3mm ，以便于能够检测到毛刺（翻边）。,7/9/2020,a,9,Part No CN15-N1407,Up date the changes and sent me the updated data then Please Go for manufacturing,Provide car line with150mm pitch,Provide Swivel form check template min two numbers. See slide no 2,至少应有两个样板刀。参照图片2,应有汽车坐标，并以150mm 为间距 。,将修改后的设计发送给我们，然后进行制造。,

8、7/9/2020,a,10,Part No CN15-N43881,Up date the changes and sent me the updated data then Please Go for manufacturing,Remove this relive.,将修改后的设计发送给我们，然后进行制造。,去除该让开,7/9/2020,a,11,Part No CN15-18D317,Up date the changes and sent me the updated data then Please Go for manufacturing,Part clamping as per

9、LD data,Provide Swivel form check template min two numbers. See slide no 2,将修改后的设计发送给我们，然后进行制造。,零件夹持应符合零件检测要求,至少应有两个样板刀。参照图片2,7/9/2020,a,12,Checking fixture,Part No CN15-N02030,Up date the changes and sent me the updated data then Please Go for manufacturing,Direction of the checking fixture to be c

10、hanged,将修改后的设计发送给我们，然后进行制造。,检具,检具方向应修改,7/9/2020,a,13,Part No CN15-16H004,Up date the changes and sent me the updated data then Please Go for manufacturing,Provide car line with150mm pitch,Provide Swivel form check template min two numbers. See slide no 2,将修改后的设计发送给我们，然后进行制造。,应有汽车坐标，并以150mm 为间距 。,至少应

11、有两个样板刀。参照图片2,7/9/2020,a,14,Part No CN15-N40014,Up date the changes and sent me the updated data then Please Go for manufacturing,Provide car line with150mm pitch,Provide Swivel form check template min two numbers. See slide no 2,将修改后的设计发送给我们，然后进行制造。,应有汽车坐标，并以150mm 为间距 。,至少应有两个样板刀。参照图片2,7/9/2020,a,15,Part No CN15-1A457,Please Go for manufacturing,Provide car line with 50mm pitch,请继续进行制造,应有汽车坐标，并以50mm 为间距 。,7/9/2020,a,