元器件规格书fd1260-s3012c4kl风扇

1、ACT-RX TECHNOLOGY CORPORATIONCUSTOMER:MODELNO:6015I(DC Brushless Fan)PARTNO:FD1260-S3012C4KL-LBDATE: JUNE12012Page 1 of 11REV.：A00Approved by:许勇 6/112QC by:周正刚 6/112Checked by:周建将 6/112Checked by:6/112Prepared by:周建将 6/112ACT-RX TECHNOLOGY CORPORATIONTEL: 886-2-824211112F, No. 192, Lien Chen Road, C

2、hung Ho City,FAX: 886-2-82452200 Taipei, R.O.C.CUSTOMER APPROVALACT-RX TECHNOLOGY CORPORATIONCONTENTS1. SCOPE32. ELECTRICAL33. MATERIAL44. MECHANICAL45. EXPECTED LIFE SPAN （MTBF）46. NOISE MEASUREMENT57. RELIABILITY6-78. PRODUCT LABEL79. PERFORMANCE CHART810. ASSEMBLY DIAGRAM911. ORDERING AND OPERATI

3、NG REMARKS1012. FAN PACKING DATA11.Page 2 of 11REV:X00ACT-RX TECHNOLOGY CORPORATION1. SCOPEThis document is a specification defining the electrical and mechanical characteristics of the product.2. ELECTRICALStandard operating condition is 25, 65%RH ambient, unless otherwise specified.Page 3 of 11REV

4、:X00ItemSpecificationTest Condition1Rated Voltage12V 10%DC power supply2Rated Current0.12 Amp (Typical)DC power supply at Rated Voltage3Max. Current0.13 Amp10% (Safety Regulation)DC power supply at Rated Voltage. This is for Safety Regulation.4Rated Power1.44 WAt Rated Voltage.5Starting Voltage7V (M

5、ax.)DC power supply5Insulation Resistance10 M (Min.)Input 500V(DC) between Lead wire(+) and housing7Speed4500 RPM 10%Measured at 5 minutesafter starting under 255, 65 5%RH ambient8Acoustical Noise34.0dB(A)(measurement tolerance 2 dBA)Measured at typical speed with an acoustic microphone 1 meter away

6、 from the fan intake in a test chamber with background noise level below 18dB(A) under ISO-3745 Standard, refer to NOISE MEASUREMENT ITEM 7.9Static Pressure4.18 mm-H2O (0.16 inch-H2O )Refer to PERFORMANCE CHARTITEM 9 at zero airflow.This measurement is performed AMCA 210-99 Standard.10Air Flow15.22

7、CFM (0.43CMM )Refer to PERFORMANCE CHARTITEM 9 at zero static Pressure. This measurement is performed AMCA 210-99 standard.11Direction of rotationCounter-anticlockwiseDC power supply, viewed from impeller.ACT-RX TECHNOLOGY CORPORATION3. MATERIAL4.MECHANICAL5.EXPECTED LIFE SPAN （MTBF）At a standard op

8、erating condition of 255 , 655%RH ambient, the expectedlife(expressed as Mean Time Between Failure) of products are evaluated under MIL-STD-781 Standard as below ：Two Ball Bearing：65000 hrs , Continuous operating under 25 65%RH One Ball One Sleeve Bearing：50000 hrs , Continuous operating under 25 65

9、%RHSleeve Bearing：30000 hrs , Continuous operating under 25 65%RHAlloy Sleeve with Ceramic Shaft：300000 hrs , Continuous operating under 25 65%RHCeramic Bearing with Ceramic Shaft：500000 hrs , Continuous operating under 25 65%RHPage 4 of 11REV:X00DimensionsL * W * H =60*60*15.3(mm)Weight30 gramsStan

10、dard operating temperature range-10 75 Standard storage temperature-20 80 Bearing systemTwo Ball BearingOne Ball One Sleeve Bearing Sleeve BearingAlloy Sleeve with Ceramic Shaft Ceramic Bearing with Ceramic ShaftImpellerPBT UL94-V0FramePBT UL94-V0BobbinPBT UL94-V0+：RedLead Wire：BlackO/P:WhiteYellow2

11、4UL 1007 AWG2628ACT-RX TECHNOLOGY CORPORATION6. NOISE MEASUREMENT：B & K 4190Noise is measured under Rated Voltage in free air in the anechoic chamber with B & K Nexus 4350 conditioning amplifier, with B & K 4190 microphone at a distance of one meter from the fan intake. The background noise is 18dBA

12、 max under the ISO-3745Standard.Page 5 of 11REV:X00ACT-RX TECHNOLOGY CORPORATION7. RELIABILITYPage 6 of 11REV:X00ItemSpecificationTest Condition1Locked Rotor TestFlameproof and damage freeRotor locked for 72 hrs with Rated Voltage2Reverse Voltage Test ProtectionYesReverse with Rated Voltage3Balance

13、TestNo protruding beyond the circle within 10 secondsThe fan runs in a circle, scaled by fan radius plus 10mm, on a perfectly smooth plate for 10 seconds under the ISO 1940 G6.3grade Standard.4Drop TestAll specified characteristics remain unchangedDrop D.U.T.(The standard packing) from the test mach

14、ine at 76cm below. Individual one angle, three diagonal corners and six planes under the ISTA-1AStandard.5Vibration TestAll specified characteristics remain unchangedAmbient temp.：25 C5 C with Rated VoltageAmplitude：0.4-2.5 mm Acceleration：14.7 S/m2 Frequency：10HZ-60HZ Sweeping period：1 min 10HZ-60H

15、Z：30 seconds 60HZ-10HZ：30 seconds Total：10 cyclesThis test is under the IEC 68-2-6 Standard.6High/Low Temperature CyclingAll specified characteristics remain unchanged20 minutes slew rate +75 C (1 hr)，10 C (1 hr)Total：36 cycles with Rated Voltage This test is under IEC 68-2-38Standard.7Low Temp. Sto

16、rageAll specified characteristics remain unchangedTested under standard condition ；after 500hrs, -20 Cstorage, without power supply. This test is under IEC 68-2-1 Standard.8High Temp. StorageAll specified characteristics remain unchangedTested under standard condition ；after 500hrs, 80 Cstorage, wit

17、hout power supply. This test is under IEC 68-2-2ACT-RX TECHNOLOGY CORPORATION8. PRODUCT LABEL26489Page 7 of 11REV:X00Standard.9Dielectric StrengthMax 1mA of leakage CurrentInput 500V(AC) for 1 sec between lead (+/-) and housingACT-RX TECHNOLOGY CORPORATION9. PERFORMANCE CHARTThis measurement is acco

18、rding to the AMCA 210-99 Standard.PQ curve for FD1260-S3012C2KL under Rated Voltage.Page 8 of 11REV:X00ACT-RX TECHNOLOGY CORPORATION10.ASSEMBLY DIAGRAMROTATIONAIR FLOWNote ：1. L*：Lead wire length：15010mm （From frame edge）Page 9 of 11REV:X00LABEL啞伎朏斮杶奪*ACT-RX TECHNOLOGY CORPORATION11. ORDERING AND OP

19、ERATING REMARKS11.1 Please indicate Part No. on every order.11.2 For those not specified but vital to your requirement, ACT-RX is in full position to supply qualified substitutes.11.3 ACT-RX does not guarantee the product if applications exceed specified limitations.11.4 Please do not touch the impe

20、ller and never carry the fan the lead wires. Thebearings and the lead wires may be damaged.11.5 Please do not use the fan in the environment of corrosive gas or liquid.11.6 Please do not store the fan in the environment of high humidity. Please avoid storage of the fan over 6 months . For long term storage,