射线中英文报告VIP

1、页眉内容射线检测评定记录ZJN/8.6-19-2WeldRadiographicNegativeAssess TablePage 1 of1产品名称Product Name材质Material片号焊缝号FilmWeld NoNo评片级别Evaluated class工作令号工件名称Work NoPart Name厚度焊缝编号ThicknessWeld No缺陷性缺陷位置象质指备注缺陷量质Defect of Location黑度RemaDefectNo.of数 Wire150 150DensityrksTypeDefectIdentity评片 :日期 :复评 :日期Evaluated by:Da

2、te:Re-Evaluated by:Date:1 页脚内容页眉内容Exegesis: A-Crack( 裂纹 ). B-Lack of fusion( 未熔合 ). C-Lack of penetration( 未焊透 ). D-Rotundity-defect( 圆形缺陷 ). E-Strip-defect( 条状缺陷 )焊缝射线检测报告Radiographic Examination Report For Weld SeamZJN/8.6-19-1产品名称工作令号Product NameJob No材质报告编号MaterialReport No源种类 Ir192CO60设备型号Type

3、of SourceEquip. Type焦点尺寸2*2胶片牌号Focus SizeFilm Brand增感方式前屏 Front0.03mm后屏 Back 0.1mm胶片规格PbFilm SizeIntensifying Means象质计型号/ 冲洗条件自动 Auto. 手工 ManualType of Image Quality IndicatorWashing Method检显影液配方天 山显影条件5 Min,20Content of Developing LiquidDeveloping Condition测照相质量等级 ABB底片黑度2.0 4.0Illumination LevelFi

4、lm Density条焊缝编号 Seam No件板厚mm及Plate Thickness工透照方式Radiography Method艺 L1 （焦距）mm参数Focus To Film Distance能量 Energy(kV)管电流 Tube Current(源活度 Bq)mA曝光时间minLightening Time要求象质指数Required Image Quality Index焊缝长度(mm)Seam Length一次透照长度Once Radiographic Length合格级别（级）Qualified Level要求检测比例%Required Test Ratio实际检测比例

5、%Actual Test Ratio扩探比例%Extended Test Ratio检测标准JB/T4730.2-2005检测工艺编号JN/QD8.2-01-07Acc. StandardExam. Process No合格片数A 类焊缝B 类焊缝相交焊缝共 计最终评定结果级级级级Level ILevel IILevel IIILevel Qualified Film CategoriesACategories B Intersect PositionTotalFinalNumber张张张张Evaluating张张张张Results缺陷及返修情况说明检测结果Specification For

6、Defect And RepairConclusion1.本台产品返修片共计0 张，最高返修次数0 次2.超标缺陷部位返修后经复验合格。3.返修部位原缺陷情况见焊缝射线检测底片评定记录。1.The total of repair for this product is 0 . The maximum repair at the same location is 0 times.2.After the defect repaired, retesting is qualified.3.The defect conditions of repairing location is referred

7、to the evaluating list of radiographic test film.1.本台产品焊接一次合格率100 %。2.本台产品焊缝质量符合III级的要求，结果合格。3.检测位置及底片情况详见焊缝射线底片评定记录及射线检测位置示意图。1.The primary welding acceptance rate of this product is 100%2.The quality of theweld seam for this product confirms to the requirements ofthe applied level. The result is acceptance.3.The test locationand filmconditions are referred to the evaluation list ofradiographic testing film and the location sketch of radiographic test.2 页脚内容页眉内容报告人（资格）审核人（资格）无损检测专用章年月日Reported byReviewed bySeal for NDEDate :年月日Date:年月日Date:无损检测部位布置图ZJN/8.6-18Examination Position Sche