材料科学基础(哈工大版)课件_第1页
材料科学基础(哈工大版)课件_第2页
材料科学基础(哈工大版)课件_第3页
材料科学基础(哈工大版)课件_第4页
材料科学基础(哈工大版)课件_第5页
已阅读5页,还剩81页未读 继续免费阅读

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

材料科学基础第一章 材料的结构前言材料热处理学报, 29( 1), 99 101, 2008304 奥氏体不锈钢热诱发马氏体相变研究杨卓越、王 建、陈嘉砚摘 要 : 借助 X射线衍射技术 ,研究了 304 奥氏体不锈钢热诱发马氏体相变倾向。结果表明 :C、 Mn、 Cr 和 Ni接近标准规范下限 ,304 不锈钢的稳定性急剧下降 ,致使液氮内冷却后的奥氏体转变为 或 马氏体 ,室温拉伸即形成应变诱发 和 马氏体 ,而且较小的室温变形显著增大随后液氮内冷却的热诱发 马氏体相变倾向 ,但随室温预应变增大快速形成应变诱发 马氏体 ,致使随后在液氮内发生热诱发 马氏体倾向下降。此外 ,研究表明 马氏体的形成及消失与 马氏体的累积量有关。Shui Li, Jin Tao, Tian Sugui , Hu Zhuangqi :Influence of precipitate morphology on tensile creep of a single crystal nickel-base superalloyAbstractThe influence of the precipitate morphology on the creep properties of 0 0 1-orientated specimens of a nickel-base single crystal superalloy has been investigated. Specimens with two different microstructures, namely as-heat treated crystals with cuboidal particles and crystals given a compression pre-treatment to form a raft microstructure orientated parallel to the stress axis, were crept at 800 and 1000 C. The analysis of the experiments show that, at 800 C and 600MPa, the alloy with cuboidal precipitates exhibited both lower creep rates and longer rupture lives compared to those with rafted . TEM examination showed that, in addition to 1 1 1 1 1 0-slip system operated in matrix, the precipitates are cut by superlattice dislocations and stacking fault. It indicated that dislocations could shear the semi-coherent rafts relatively easily ompared to the coherent cuboidal . At 1000 C and 200MPa, the alloy with raft microstructure exhibited an extremely low minimum creep rate and longer rupture life. The dislocations movement by the combination of climbing and gliding processes and the glideclimb along / vertical interfaces are impeded most strongly. This indicates that the rafted structure is beneficial to improving creep resistance of the alloy under the test condition.Materials Science and Engineering A 454455 (2007) 461466Fig. 5. Dislocation structure of a precompression treatment specimens during creep at 800 C and 600MPa: (a) t = 0, (b) t=10h, (c) t = 50 h and (d) after fail at t = 287 h.Fig. 8. Schematic of dislocation shearing precipitate by stacking fault相关概念:n 304不锈钢热诱发 :液氮拉伸变形液氮 X光、 TEM 奥氏体 立方马氏体 六方 马氏体 X射线、 TEM : 111 200 220 311 n nickel-base superalloy0 0 1-orientated : 001 位向single crystal: 单晶体cuboidal particles: 立方系颗粒1 1 1 1 1 0-slip system : 滑移系dislocations and stacking fault: 位错和层错dislocations climbing and gliding:位错攀移和滑移 相变机制:固态相变:过饱和固溶体 蠕变:位错 层错 滑移 攀移 晶体学基础: 结构:单晶体 多晶体 原子排列:体心立方 面心立方 密排六方 晶体表征:晶面指数 晶向指数内容及要求:懂会 熟(练习)本章内容1. 化学键 2. 晶体和非晶体3. 空间点阵 4要素 14种点阵( 7个晶系)阵点 晶向 晶面 晶胞(单胞) 4. 晶向指数 5. 晶面指数6. 典型金属晶体结构:体心立方 面心立方 密排六方 7. 合金相结构: 固溶体 中间相1.1 材料的结合方式化学键:质点间的作用力共价键: 共用电子对所产生的力离子键: 两种离子间的静电力金属键: 属正离子与自由电子之间的力范德瓦尔斯键:正负电荷部分间的微弱静电力共价键离子键金属键1.2 晶体学基础原子排列:无序 短程有序 长程有序 晶体:三维、周期性重复(整齐排列) 近程有序一、空间点阵n质点几何点n空间点阵: 阵点 结构单元 (原子、离子、分子、集团)晶格n晶体结构晶体点阵n晶胞:对称、棱角、直角、体积对称最好 棱角最多 直角最多 体积最小晶胞的表征: X-Y-Z a-b-c -布拉菲点阵: “每个 阵点 环境相同 ” ( 1848)14种点阵 7个晶系7个晶系 14种点阵课堂练习 1 11. 晶胞的表征2. 画出面心立方、体心立方、密排六方结构图。3. 画图说明面心立方点阵可以表示为体心立方点阵。4. 画 14种单胞 5. 举例说明 和 uvw 、 hkl 与 ( hkl ) 的区别 练习 1 1 参考答案二、晶向指数和晶面指数n 晶向指数n 晶面

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论