路由器交换机配置

路由器：RouterenRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#intRouter(config)#interface f0/0Router(config-if)#ip add 192.168.1.1 255.255.255.0Router(config-if)#exitRouter(config)#intRouter(config)#interface f0/0.2Router(config-subif)#enRouter(config-subif)#encapsulation doRouter(config-subif)#encapsulation dot1Q 2Router(config-subif)#ip add 192.168.2.1 255.255.255.0Router(config-subif)#exitRouter(config)#intRouter(config)#interface f0/0.3Router(config-subif)#enRouter(config-subif)#encapsulation doRouter(config-subif)#encapsulation dot1Q 3Router(config-subif)#ip add 192.168.3.1 255.255.255.0Router(config-subif)#exitRouter(config)#intRouter(config)#interface f0/0Router(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up%LINK-5-CHANGED: Interface FastEthernet0/0.2, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.2, changed state to up%LINK-5-CHANGED: Interface FastEthernet0/0.3, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.3, changed state to upRouter(config-if)#交换机 1：SwitchenSwitch#conf tEnter configuration commands, one per line. End with CNTL/Z.Switch(config)#intSwitch(config)#interface f0/2Switch(config-if)#swSwitch(config-if)#switchport mode accessSwitch(config-if)#swSwitch(config-if)#switchport access vlan 1Switch(config-if)#exitSwitch(config)#intSwitch(config)#interface f0/3Switch(config-if)#swSwitch(config-if)#switchport mode accessSwitch(config-if)#swSwitch(config-if)#switchport access vlan 1Switch(config-if)#exitSwitch(config)#intSwitch(config)#interface f0/4Switch(config-if)#swSwitch(config-if)#switchport mode accessSwitch(config-if)#swSwitch(config-if)#switchport access vlan 2% Access VLAN does not exist. Creating vlan 2Switch(config-if)#exitSwitch(config)#intSwitch(config)#interface f0/1Switch(config-if)#swSwitch(config-if)#switchport mode trunkSwitch(config-if)#exitSwitch(config)#intSwitch(config)#interface f0/5Switch(config-if)#swSwitch(config-if)#switchport mode trunk%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state to down%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state to upSwitch(config-if)#vlan 3Switch(config-vlan)#%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up交换机 2：SwitchenSwitch#conf tEnter configuration commands, one per line. End with CNTL/Z.Switch(config)#intSwitch(config)#interface f0/1Switch(config-if)#swSwitch(config-if)#switchport mode accessSwitch(config-if)#swSwitch(config-if)#switchport access vlan 2% Access VLAN does not exist. Creating vlan 2Switch(config-if)#exitSwitch(config)#intSwitch(config)#interface f0/2Switch(config-if)#swSwitch(config-if)#switchport mode accessSwitch(config-if)#swSwitch(config-if)#switchport access vlan 3% Access VLAN does not exist. Creating vlan 3Switch(config-if)#exitSwitch(config)#intSwitch(config)#interface f0/3Switch(config-if)#swSwitch(config-if)#switchport mode accessSwitch(config-if)#swSwitch(config-if)#sw