JWB-75型无极绳绞车设计【含6张CAD图纸、说明书】
收藏
资源目录
压缩包内文档预览：
编号：15752340
类型：共享资源
大小：1.54MB
格式：ZIP
上传时间：2019-03-07
上传人：机****料
认证信息
个人认证
高**（实名认证）
河南
IP属地：河南
50
积分
- 关 键 词：
-
含6张CAD图纸、说明书
无极绳绞车设计【
张CAD图纸
设计含CAD图纸
CAD图纸设计
型无极绳绞车
- 资源描述：
-
- 内容简介：
-
英文原文Reducing Commercial Fishing Deck Hazards with Engineering Solutions for Winch DesignJennifer M. Lincoln a,* , Devin L. Lucas a , Robert W. McKibbin b,Chelsea C. Woodward b, John E. Bevan ba NIOSH Alaska Field Station, Anchorage Alaskab NIOSH Spokane Research Lab, Spokane WashingtonAvailable online 20 March 2008AbstractIntroduction: The majority (67%) of hospitalized injuries among Alaska commercial fishermen are associated with deck machinery. This paper describes the “Prevention Through Design” process to mitigate one serious machinery entanglement hazard posed by a capstan deck winch. Methods: After observing that the capstan winch provides no entanglement protection and the hydraulic controls are usually out of reach of the entangled person, NIOSH personnel met with fishermen and winch manufacturers to discuss various design solutions to mitigate these hazards. Results: An emergency-stop (“e-stop”) system was developed that incorporated a momentary contact button that when pushed, switches a safety-relay that deenergizes the solenoid of an electro-hydraulic valve stopping the rotating winch. The vessel owners that had the e-stop installed enthusiastically recommend it to other fishermen. NIOSH entered into a Proprietary Technology Licensing Agreement with a company to develop the system for commercial use. Conclusions: This is an example of a practical engineering control that effectively protects workers from a hazardous piece of equipment by preventing injuries due to entanglement. This solution could reduce these types of debilitating injuries and fatalities in this industry. 2008 National Safety Council and Elsevier Ltd. All rights reserved.Keywords: Prevention through design; PtD; Commercial fishing; Entanglement hazards; Engineering solution; Injury prevention1. IntroductionCommercial fishing is the most dangerous occupation in the United States. In 2006, 51 commercial fishermen were killed on the job resulting in an occupational fatality rate of 142 per 100,000 workers, the highest rate for any occupation in the United States and 36 times higher than the average fatality rate for all U.S. workers (Bureau of Labor Statistics BLS, 2007). During 19942004, 641 commercial fishermen died in the United States. Of these, 332 (52%) died after their vessel sank, and another 184 (29%) fatalities were due to falls overboard. The remainder of the fatalities were due to a variety of causes, including deck injuries (51, 8%; Dickey & Ellis, 2006). These fatal deck injuries are from machinery and fishing gear. In Alaska, fatal deck injuries are even more prevalent, accounting for 12% of all fatalities during 20002006 (Commercial Fishing Incident Database CFID, 2007). Prevention efforts should emphasize preventing the loss of life due to the loss of a vessel, falls overboard, and injuries on deck. This paper focuses on the efforts to prevent injuries on deck, including the redesign of machinery or the retrofitting of safety features on fishing machinery and equipment.An important issue to address is jurisdiction of regulatory agencies on uninspected commercial fishing vessels. Both the Occupational Safety and Health Administration (OSHA) and the U.S. Coast Guard (USCG) have authority over the safety of employees onboard commercial fishing vessels. The USCG is the lead agency; OSHA only has jurisdiction out to 3 miles from shore. In addition OSHA is precluded from enforcement with respect to working conditions regulated by other federal agencies. Therefore, the promulgation of safety regulations by the USCG preempts OSHA with respect to those working conditions specifically addressed by Coast Guard regulations. The USCG does have regulations in regard to machine guarding, but the extent to which these are enforced is limited.In Alaska, most fatalities in the commercial fishing industry are also due to the loss of a fishing vessel. However, injury epidemiologists at the National Institute for Occupational Safety and Health (NIOSH) Alaska Field Station have shown that most (67%) severe nonfatal injuries occur on deck during the deployment and retrieval of fishing gear (Thomas, Lincoln, Husberg, & Conway, 2001). Severe nonfatal injuries are defined as those requiring hospitalization and include lacerations, broken bones, severe head injuries, and smashed limbs. The deck of a fishing boat is a slippery, constantly moving work platform that is often congested with machinery and fishing equipment. Many of the deck machines used on commercial fishing vessels lack adequate guarding and safety features and entanglement is a particular hazard. NIOSH found that during 19912002, 798 fishermen were hospitalized for severe nonfatal injuries, which is equivalent to an annual rate of 410 per 100,000 full-time equivalent fishermen. Of these injuries, 23% were due to being entangled or struck by lines or gear, or being trapped in a winch, pulley, or other deck equipment (Lincoln, Husberg, & Mode, 2006). Experts have recommended that vessel machinery be redesigned or retrofitted with safety features to prevent these types of injuries (Husberg, Lincoln, & Conway, 2001; Burgess, 2001). The purpose of this paper is to describe the “Prevention Through Design” activities we completed in order to mitigate one machinery entanglement hazard posed by a deck winch commonly found on commercial fishing vessels.2. MethodsNIOSH is the federal agency responsible for conducting research and making recommendations to improve the safety and health of workers in the United States. The NIOSH Alaska Field Station has worked in the area of commercial fishing safety since 1991. After working with our industry partners on several safety issues, NIOSH developed the Deck Safety Intervention Project, which began in October 2000. Goals of this project were to determine when and where deck injuries occur and to develop intervention strategies. These intervention strategies included engineering designs with industry input to eliminate or lessen the risks deck machines pose. In 2002, NIOSH injury epidemiologists met with fishermen across Alaska to discuss the problem that 67% of severe hospitalized injuries were a result of deck machinery, with the hope that practical solutions could be developed to preventthese injuries from occurring. One significant entanglement problem fishermen identified was that posed by the capstan-type winches typically found on purse-seine vessels. Vessels fishing with purse-seine gear are generally about 50- feet long and are accompanied by a skiff, which is integral to the fishing operation. The seine is a large net with thick mesh and small openings. It is not designed to catch fish in the mesh; rather, the net acts as a large cage trapping the fish. The seine is set by using the skiff to pull one end of the net off the stern of the vessel. The skiff is brought around so that the seine makes a half circle with the skiff on one end and the vessel on the other end. Both ends are towed equally to gather a school of fish. Then, the skiff pulls its end over to the vessel completing the circle. At this point, a line, which is threaded through rings at the bottom of the net, is wrapped around the drum of the capstan deck winch and pulled in. This line, the “purse-line,” draws the bottom of the net together making a large “bag” or purse. The fish trapped in the purse are brought onboard and dumped in the fish hold.The deck winch on purse-seine vessels is a powerful (up to 1000 foot-pounds of torque) capstan winch, usually mounted in the center of the deck near the wheelhouse. Its drum rotates while the crew is working on deck. Fishermen who lose their balance or are inattentive can become entangled in the purseseine as the line is winding around the drum. Crushing injuries to the hand or arm, and in some cases fatalities if the head or torso is caught, are the results. The winch hydraulic motor controls are usually located on the bulkhead just forward of the winch. Unfortunately, they are usually out of reach of the entangled fisherman to stop the drum rotation. In June 2002, tragedy struck the captain of a commercial purseseine vessel fishing for salmon in Prince William Sound, Alaska. The crew had just set the seine around a school of fish. After drifting with the net open for about 15 minutes, the captain called for the skiff-man to close the net, which was done without incident. Then, as the captain wrapped the purse line around the drum of the deck winch to close the bottom of the seine, he reached across the winch, brushing his raincoat sleeve against the moving line. The sleeve caught between the line and the rotating drum. He called for help as he was being wrapped into the spinning drum. Two crewmen charged across the deck from the stern where they tried to work the hydraulic winch controls, located on the backside of the pilot-house. However, the captain had gone around the winch three times before it was stopped. Despite the best efforts of the crew and others nearby, the captain died the next day at an Anchorage hospital from multiple traumatic injuries. One year later in October 2003, another purse-seine captain was killed in the same type of capstan deck winch near Homer, Alaska. Working alone during an opening for rockfish, he was using the deck winch to lower a bag of fish that he had just weighed into the fish hold. Evidence suggested that the captains right hand got too close to the rotating drum and his coat sleeve got caught in the line. Entangled in the deck winch, the controls were out of reach and the rotating winch could not be stopped. The captains body was found mangled and wrapped repeatedly around the capstan several days later when his wife reported him overdue to the U.S. Coast Guard. NIOSH investigations identified two major safety hazards: no entanglement protection is provided by the winch and the hydraulic controls are usually out of reach of the person who is entangled. Injury epidemiologists from the NIOSH Alaska Field Station partnered with engineers at the NIOSH Spokane Research Laboratory to design a practical engineering solution to mitigate these safety hazards. This NIOSH team of epidemiologists and engineers met with vessel owners, purse-seine fishermen, and winch manufacturers to discuss the various safety design options. It was quickly realized that standard machine guarding and “dead-man switch” solutions were either not feasible or applicable to the typical machine use. Pressure mats for the dead-man switch would be subject to false signals from lines being coiled on deck, or from fish as the net is dumped. Physical guards are impractical because lines are fed onto the winch from virtually any angle using the fixed winch horns in combination with the rotating drums (complicated by the fact that both drums are sometimes used at the same time with lines from two directions). Rain or ocean spray would interfere with light curtains. Design considerations also favored systems that would be simple, affordable, unobtrusive, applicable to various winch models, use off-the-shelf components, not disable other vessel functions (such as the rudder or anchor winch), not interfere with normal fishing operations if the emergency-stop system failed, and most importantly have the capability to be activated by the person being entangled in time to prevent serious injury (McKibbin & Woodward, 2006).3. ResultsThe engineering design solution that was developed was an emergency-stop (“e-stop”) system that incorporated a robust, low-profile, momentary contact button mounted on the top portside winch horn. This location was the preferredmounting spot for a fisherman pursing the net from the starboard side of the vessel (the most common scenario). When pushed, the button energizes a safety-relay that in turn deenergizes the solenoid of an electro-hydraulic valve. This valve, plumbed between the manual valve that controls winch rotation and the winch drive motor, closes the flow of hydraulic oil to and from the winch motor and locks the capstan drums in place. If the emergency switch is pressed in a timely manner and the hydraulic motor does not have significant wear in the vane seals, the winch drums will lock almost instantaneously. When the electro-hydraulic valve is de-energized, the valve-spool shifts to the default position to block the oil flow to and from the winch motor. This functions as a hydraulic brake on the winch enabling a Category 0 stop. If the electric power to the electrohydraulic valve is turned off for any reason, the hydraulic fluid flow stops and the winch will not operate until the power is returned and the e-stop circuit is reset. If the winch drum has significant external rotational force acting upon it, and the motor seals are in need of repair, back-spooling of the winch drums could occur after the hydraulic valve closes both pump and tank motor ports. The back-spooling drums could effectively unwind the victim from the entanglement. The time it takes the victim to strike the emergency switch is thus the controlling factor in arresting the drum rotation, not the valve response time. With the drums turning at a typical working speed (4060 rpm), and considering a typical humanresponse time (less than 0.5 sec), the winch drums could be stopped in less than 180 of rotation sufficient to limit serious entanglement injury. A control box containing the safety-relay, pilot lights to indicate system status, and a system reset button, is mounted adjacent to the winch directional control valve. In the event someone becomes entangled, it is important that the winch directional control valve be returned to neutral before the e-stop system is reset; otherwise, further entanglement or injury could result by the rotating drum. On purse seine vessels, the manual winch directional-control valve is almost always mounted on the rear bulkhead of the vessel, usually about 5- to 6-feet forward of the capstan winch. The normal function of the manual valve precludes having a self-centering spool. The fisherman typically shifts the spool for either a forward or reverse winch operation, then leaves the winch running to execute his/her fishing duties. If there is a winch entanglement and the e-stop is used to stop the drum rotation, the safety relay requires a manual reset. If the prototype system was reset without verifying that the manual valves were in the neutral position, the winch drums may start to rotate again unexpectedly. The position of the reset function was moved from the position of the e-stop switch to the proximity of the manual valves. In the described scenario, this operating location removes the reset-switch operator from the possible hazardous area near the rotating winch drums. Yet, he/she is close enough to make a visual inspection of the clearance around the winch and to be able to observe the position of the manual valves, before resetting the system. This design lends itself to the development of more advanced systems. Additional buttons, easily wired in parallel to the winch e-stop button, can be placed in other locations on the vessel such as in the wheelhouse or along the gunwales, leaving the reset switch at the manual winch controls. The e-stop system may be applied to other types of deck machinery, and may eventually incorporate wireless or voice activation features. A fishing vessel owner/operator home-ported in Seattle, Washington worked with NIOSH on the design and installation of this e-stop system, which was successfully tested during the 20052007 Southeast Alaska salmon seasons. This vessels crew praised the device as a significant safety and, surprisingly, productivity improvement. As of this writing, they continue to use the winch e-stop system. The crewmembers have reported that although they have not had to use it in an emergency, it has come in handy when the purse-line gets knotted up while operating. This capstan winch e-stop system has been installed by NIOSH on two other seiners that operate in Alaska. Feedback from a qualitative evaluation of the e-stop system was completed. We asked the skippers who are currently using the system questions in regard to its acceptability, use in an emergency, its reliability, durability, possible design improvements, and examples of how it is making their fishing more efficient. The other fishing crews also like having the e-stop on their vessels. They believe the e-stop is very helpful, very important, and would enthusiastically recommend it to other fishermen. None of them have had to use it in an emergency. They did indicate that they found it increases efficiency because they are able to stop the winch faster when something is wrong with the lines. On rare occasions, the button is sometimes pushed unintentionally by someones hand or elbow, but the system can be quickly reset so as not to be a problem. Note that the NIOSH designed e-stop does not reset automatically, and it cannot be reset by pushing the e-stop button a second time (i.e. toggling). It requires that someone manually push the reset button mounted in the control box on the rear bulkhead. Fishermen who have used the system are so pleased with it that they have cited other pieces of machinery on their vessels that could be made safer with similar e-stop buttons. The e-stop has received strong support at industry trade shows. It has been demonstrated at Pacific Marine Expo in Seattle in 2005, 2006 and 2007, the largest commercial fishing trade show in the United States, and at Comfish Alaska in Kodiak in 2007. The e-stop has received an overwhelming positive response from fishermen, with many fishing vessel owners and operators requesting information on how to obtain the device for their vessels. NIOSH staff have also produced and distributed copies of a deck safety awareness DVD that illustrates the entanglement hazard and e-stop solution to the hazard (NIOSH, 2007). Over 100 DVDs have been distributed to fishermen, marine safety organizations, and government agencies in the nine months since production. In the next year, a control technology publication will be written to increase the distribution and impact of this e-stop solution. The NIOSH intervention design has been licensed to a manufacturer. In November 2007, NIOSH entered into a Proprietary Technology Licensing Agreement with Emerald Marine Products, LLC (Seattle, WA) to develop the e-stop system for commercial use. Emerald Marine Products, in cooperation with Kolstrand Marine Supply (Seattle, WA), will be manufacturing a similar system based on the NIOSH research. They will be selling the e-stop exclusively through their distributor Go2Marine.4. ConclusionsThe e-stop is an example of a practical engineering control or physical modification that can be implemented to protect workers from a hazardous piece of equipment such as the capstan winch. Taking from the injury prevention literature (Haddon, 1972), the most effective control of the hazard would be to “Prevent the creation of the hazard in the first place” by eliminating the use of the deck winch. This type of winch is not used in the European Union and some operators in the United States have eliminated it from their operation as well. However, if this cannot be done, engineering controls are the most desirable type of hazard intervention because they separate the worker from the hazard and decrease the possibility of an incident occurring.By using injury epidemiology to identify problems, along with practical industry input, effective safety interventions to control such hazards can be designed and implemented. This “prevention through design” approach should prove effective in providing tools for this dangerous industry to prevent injuries on deck, and hopefully inspire others to apply similar ideas to these types of hazards.中文翻译减少商业捕鱼甲板危险的绞车设计工程方案Jennifer M. Lincoln a,* , Devin L. Lucas a , Robert W. McKibbin b,Chelsea C. Woodward b, John E. Bevan ba NIOSH Alaska Field Station, Anchorage Alaskab NIOSH Spokane Research Lab, Spokane WashingtonAvailable online 20 March 2008摘 要：大多数（67）阿拉斯加的商业渔民受伤住院都与甲板机械有关。本文介绍了“通过设计来预防”的理念，以减轻由甲板绞车绳缆缠绕造成的严重机械危害。措施:经过观察后发现，起锚机没有提供任何防止缠绕的保护，并且液压控制不受人的控制。NIOSH的工作人员会见了渔民和绞盘制造商讨论各种设计方案，以减轻这些危险。成果：开发了一个紧急停止（“estop”）系统，包括一个当按下会激发安全继电器的短暂接触按钮。安全继电器会触发电磁液压阀工作，从而使绞车停止转动。拥有紧急制动系统的船主热情的把该系统推荐给其他人。NIOSH与一家公司订立了一个专有技术许可协议开发该系统的商业用途。结论：这是一个实际的工程控制的例子。它通过避免由于缠绕造成的伤害有效地保护了工人不受危险设备的伤害。这个解决方案可以减少在这种行业里的破坏性伤害和死忘人数。关键词：通过设计来预防； 商业捕鱼； 缠绕的危险性； 工程解决方； 预防受伤1简介商业捕鱼是美国最危险的职业。2006年，51名商业渔民死于这项职业，这就导致了对全美任何一个职业来说最高并且达到全美平均水平36倍的职业病死亡率：每100000人中有147人死亡【1】。从1994年到2004年，美国有641名商业渔民死亡。其中，332（52%）死于船沉没后，另外184（29%）人是由于掉落海中而死于非命。其余的由于多种原因，包括甲板的伤害（51，8%，）【4】。这些致命的伤害是来自甲板机械和渔具。在阿拉斯加,致命的甲板伤害更普遍，占12%的死亡发生在2000-2006【2】。应该强调预防措施来保护生命不会由于损伤的机械，翻船，甲板的伤害而受到伤害。本文着重探讨了如何努力防止甲板上的伤害，包括了对渔业机械和设备的安全特点重新设计和改造。一个重要的问题是对未经检查的商业渔船的监督管理。职业安全与卫生管理局(OSHA)和美国海岸警卫队(USCG)有对商业渔船上的员工安全负责的责任。USCG是领导机构，NOISH只管辖海岸线3英里范围内的地方。USCG的法规取决于机械的遵守，但是强制的程度是限制的。在阿拉斯加,大多数商业捕鱼工作中的意外事故也是由于渔船的损失。然而，国家职业安全与健康研究所（NIOSH）的伤病流行病学家Alaska Field Station研究认为甲板上大多数严重的非致命性伤害发生在部署和检索渔具时【10】。严重的非致命性伤害定义为需要住院治疗的,包括裂痕，骨折，重型颅脑损伤，肢体破裂。一艘渔船的甲板是一个滑的、不断推进的、挤满了机器和捕鱼设备的工作平台。甲板上的许多用来商业捕鱼的机器缺少足够的保护和安全性。NIOSH研究发现在1991-2002期间，798名渔夫因为严重的非致命性伤害住院，相当于每100,000名全日制渔民有410名住院的增长率。在这些伤病中，23%是由于被绳索缠绕或者被齿轮撞伤的，或者被绞车，滑轮和其他甲板上的设备困住造成的【7】。专家推荐船舶机械根据安全措施重新翻新或设计，避免类似的伤害【6】。2措施NIOSH是美国负责进行研究和制定合理化建议来提高工人安全保障和健康的联邦机构。从1991年开始，NIOSH阿拉斯加分站就对商业捕鱼的安全性进行研究。在与我们的行业合作伙伴就几个安全问题一起工作后，NIOSH在2000年提出了the Deck Safety Intervention Project，这个计划的目的是确定甲板的伤害是何时何地发生的，同时开发预防策略。2002年NIOSH伤病流行病学家在阿拉斯加会见了渔夫，讨论了有关67%的人由于甲板机械导致严重受伤而住院的问题，希望实用的解决方案可以预防这些伤害的发生。绳索缠绕问题的一个重要发现是，渔民所造成的绞车capstantype通常在围网渔船发现。渔船捕捞围网齿轮一般大约50英尺长，这是捕渔作业不可分割的。围网是一个有着小净开口的厚厚的大网，它的目的不是要在网格捕捉鱼而是作为一个捕鱼的大笼。围网是使用小艇的船尾拉网的一个尾部。小艇在一端拉着围网围成一个半圆，船舶在另一端。两端都被拖着来围捕鱼群，然后小艇把它的一端交给母船，就完成了捕鱼的工作。在这一点上，环绕在网底的一条绳，缠绕在甲板绞盘里了。捕获的鱼被拖到船上，倾倒入鱼舱里。甲板上的绞盘机是一个强有力（1000英尺的扭矩磅）的机械，通常在靠近驾驶室的甲板中心展开。它的鼓轮转动而船员在甲板上工作。失去平衡或精神不集中的渔民会被绞车上的绳缆缠绕住，手或手臂会受到破坏性的伤害，在某些情况下，也会导致头部或躯体的受伤。绞车的液压马达控制系统通常位于绞盘的隔壁。不幸的是，它们通常是不可控制的缠在一起从而使鼓轮停止旋转。2002年6月，在阿拉斯加威廉王子海峡，悲剧降临在一艘商业捕鲑鱼的船只船长的身上。船员们开始拉着围网捕鱼。在随着张开的网漂流了15分钟后，船长下令船员收网，期间没有出现意外。然而，当船长包住甲板绞车鼓轮上的绳索时，他横越了绞车，雨衣的袖子被绳索缠住了，袖子被夹在转动的鼓轮和移动绳索之间。他寻求帮助，因为他被旋转的鼓轮卷进去。两名船员从船尾狂奔到甲板，试图使位于驾驶舱背面的液压绞车控制装置工作。然而，当绞车停止转动时，船长已经绕它转了3圈。尽管船员和其他人尽了最大的努力，第二天船长由于多重外伤死在了Anchorage医院。一年之后，在2003年10月，在阿拉斯加荷马，一名船长因为同样的原因死于非命。在石斑鱼的开放日，他独自一人工作。他正在用甲板绞车将刚称量过的一袋鱼将到鱼舱里。证据表明，船长的右手太接近了转动的鼓轮并且他的外衣袖子被绳索缠住了。因此，转动的绞车失去控制并且停不下来。几天后，他妻子向美国海岸警卫队报告他逾期未归。船长的尸体最后被发现与绞车缠在一起。NIOSH经过调查，确定了两个主要的安全隐患：绞车没有安装防缠绕的保护装置以及一旦有人被缠住绞车液压控制装置失灵。来自NIOSH阿拉斯加分站的伤病流行病学家与斯波坎研究实验室的工程师合作设计一个实际的工程解决方案，以减轻这些安全危害。NIOSH 的流行病学家和工程师团队会见了船东，渔民，绞车制造商，来讨论各种安全设计方案。他们很快就意识到，标准机械准则和“死人开关”的解决办法要么不可行，要么只适用于典型的机器。“死人开关”的压力垫会受到绳索缠绕在甲板上或渔网倾倒等虚假信号的
- 温馨提示:
1: 本站所有资源如无特殊说明，都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等，如果需要附件，请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸，网页内容里面会有图纸预览，若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 人人文库网仅提供信息存储空间，仅对用户上传内容的表现方式做保护处理，对用户上传分享的文档内容本身不做任何修改或编辑，并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容，请与我们联系，我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
人人文库网所有资源均是用户自行上传分享，仅供网友学习交流，未经上传用户书面授权，请勿作他用。
川公网安备: 51019002004831号