豪威系列磁盘阵列使用手册.doc

SB-2805SAeries豪威系列磁盘陈列使用手册系统说明1 前板说明 硬盘指示灯硬盘灯指示硬盘动作指示灯绿灯表示：硬盘已通电红灯表示：未安装硬盘橙灯表示：硬盘坏了蓝灯表示：硬盘正在进行动作1.1硬盘灯指示3.菜单Menu下面将列出SB-2805SA的设定菜单menu及选择项目Quick Volume / Raid SetupRaid Set FunctionVolume Set FunctionPhysical DrivesMain MenuRaid System FunctionEthernet ConfigurationView System EventsClear Event BufferHardware MonitorSystem InformationRaid 0Selected CapacitySelect Stripe Size4K,8K,16K,32K,64K,128KCreate Vol / Raid SetYes, NoRaid 1 or 0+1 Selected CapacitySelect Stripe Size4K,8K,16K,32K,64K,128KCreate Vol / Raid SetYes, NoRaid 0+1 +SpareSelected CapacitySelect Stripe Size4K,8K,16K,32K,64K,128KCreate Vol / Raid SetYes, NoQuick Volume / Raid SetupRaid 3Raid 5Selected CapacityCreate Vol / Raid SetYes, NoSelected CapacitySelect Stripe Size4K,8K,16K,32K,64K,128KCreate Vol / Raid SetYes, NoRaid 3 + Spare Selected CapacityCreate Vol / Raid SetYes, NoRaid 5 + Spare Selected CapacitySelect Stripe Size4K,8K,16K,32K,64K,128KCreate Vol / Raid SetYes, NoRaid 6Selected CapacitySelect Stripe Size4K,8K,16K,32K,64K,128KCreate Vol / Raid SetYes, NoRaid 6 + Spare Selected CapacitySelect Stripe Size4K,8K,16K,32K,64K,128KCreate Vol / Raid SetYes, NoCreate Raid SetSelect IDE Drives for Raid SetCh01 Ch16Create Raid SetYes, NoDelete Raid SetEdit The Raid Set NameSelect Raid Set To DeleteDelete Raid SetYes, NoAre you sure?Yes, NoExpand Raid SetSelect IDE Drives for Raid Set ExpansionSelect Drives IDE ChannelChxx Ch16Expand Raid SetYes, NoAre you sure?Yes, NoRaid Set FunctionActivate Raid SetSelect Raid Set To ActiveActivate Raid SetYes, NoAre You Sure?Yes, NoCreate Hot Spare DiskSelect Drives for Hot spare, Max 3 Hot spare supportedChxx Ch16Create Hot SpareYes, NoDelete Hot Spare DiskSelect The Hot Spare Device To Be DeletedDelete Hot SpareYes, NoRaid Set InformationSelect Raid Set To DisplayCreate Volume SetCreate Volume From Raid SetVolume CreationCreate VolumeVolume Name, Raid Level,Capacity, Stripe Size, SCSI Channel, SCSI ID, SCSI LUN, Cache Mode,Tag Queuing, Max Sync RateYes, NoInitialization ModeForeground, Background Delete Volume SetDelete Volume From Raid SetSelect Volume To DeleteDelete Volume SetYes, NoAre you sure?Yes, NoVolume Set Function Modify Volume SetModify Volume From Raid SetSelect Volume To ModifyVolume ModificationVolume Name, Raid Level, Capacity, Stripe Size,SCSI Channel, SCSI ID, SCSI LUN, Cache Mode,Tag Queuing, Max Sync Rate Check Volume SetModify VolumeYes, NoAre you sure?Yes, NoCheck Volume From Raid SetSelect Volume To CheckCheck The VolumeYes, No Stop Volume CheckStop All Volume CheckYes, NoAre you sure?Yes, NoDisplay Volume Info.Display Volume Info in RaidSelect Volume To DisplayView Drive InformationSelect The Drives Create Pass Through DiskSelect The Drives Modify Pass Through DiskSCSI Channel, SCSI ID, SCSI LUN, Cache Mode,Tag Queuing, Max Sync RatePhysical DrivesSelect The DrivesSCSI Channel, SCSI ID, SCSI LUN, Cache Mode,Tag Queuing, Max Sync Rate Delete Pass Through DiskSelect The DrivesDelete Pass ThroughYes, NoAre you sure?Yes, NoIdentify Selected DriveSelect The DrivesMute The Alert Beeper Alert Beeper SettingYes, NoDisabled, EnabledSave The SettingsYes, No Change PasswordEnter New PasswordRe-Enter PasswordSave The Password JBOD / RAID FunctionRAID, JBODConfigured AS JBOD?Yes, NoYes, NoRaid System FunctionAre you sure?Yes, NoRaid Rebuild PriorityUltraLow(5%), Low(20%),Medium(50%),High(80%)Save The SettingsYes, NoTerminal Port ConfigBaud Rate1200,2400,4800,9600,19200,38400,57600,115200Stop Bits1 bit, 2 bits Update FirmwareRestart ControllerYes, NoAre you sure?Yes, NoEthernet ConfigurationDHCP FunctionLocal IP AddressDisabled, EnabledView System EventsShow System EventsClear Event BufferClear Event BufferYes, NoHardware MonitorThe Hard Monitor InformationSystem InformationThe System Information4、创建RAID级别：1、输入密码八个0000002、选择Quick Volume/Raid setup 3、选择（RAID）级别Raid5或者 Raid5+spare 4、选择selected capacity 5、选择select stripe size 4K、8K、16K、32K、64K、128K 6、选择create vol raidset 7、选择Yey5. Web Base操作界面 使用者可另外连接网络在远端利用网际浏览器作更详细之显示与操作。5.1如何连接网际浏览器SB-2805SA的预设IP是192.168.001.100，DHCP是enable，请先在LCD显示设定面板上或终端机上设定正确的IPSB-2805SA的预设的使用者名称是admin，密码是8个0。6、设定6.1快速设定Quick Create1.选选左方的Quick Create进入快速设定画面，系统会自动检测到您所连接的硬盘数量。2.选择所需RAID level。3.设定所需做RAID的容量。4.选择执行时的模式。5.选择Stripe Size大小。6.选选Confirm The Operation后，按Submit执行RAID设定。7、设定Raid Set功能7.1Create Raid Set1.选选左方的Create Raid Set，会进入“Select The IDE Drive For RAID Set”画面，系统会自动检测到您所连接的硬盘。2.设定Raid Set Name(最多15个字节)，预设的Raid Set Name以Raid Set#显示。3.选选Confirm The Operation后，按Submit执行Raid Set设定。7.2 Delete Raid Set1.要删除Raid Set，选选左方的Delete Raid Set，会进入“Select The RAID Set to Delete”画面，系统会自动检测到现有的Raid Set并显示在画面上。2.选择所要删除的Raid Set。3.选选Confirm The Operation后，按Submit执行删除Raid Set的设定。7.3Expand Raid Set1.要把新增的硬盘加入Raid Set中，选选左方的Expand Raid Set，并选择所要扩充的RAID Set，按Submit。2.选择要加入Raid Set的硬盘。3.选选Confirm The Operation后，按Submit执行扩充Raid Set的设定。Note:1.当扩充Raid Set的设定一旦执行，即不可中断，必须完成执行。2.当扩充Raid Set的设定执行时，如有硬盘损坏的硬盘在系统中时，则当扩充Raid Set的设定执行完成后，会执行自动重建(auto rebuild)程序。7.4 Activate Incomplete Raid Set当有硬盘在系统不通电的状态下被移除时,Raid Set的状态会变更为未完成(Incomplete)。如使用者要在系统通电时能继续使用，则可执行Activate Incomplete Raid Set的选项，当执行完Activate Incomplete Raid Set后，Raid Set的状态会变更为Degraded1.选选左方的Activate Raid Set，会进入“Select The RAID Set to Activate”画面，系统会自动检测到现有的Raid Set，并显示在画面上。2.选择所要的Raid Set。3.按Submit执行Activate Raid Set的设定。7.5Create Hot Spare当使用者要执行Create Hot Spare选项时，则所有未设定Raid Set的硬盘均会显示在画面中。选选Confirm The Operation后，按Submit执行设定Hot Spare选项。7.6Delete Hot Spare选择所要删除的Hot Spare硬盘。选选Confirm The Operation后，按Submit执行删除Hot Spare选项。7.7Rescue Raid Set如需要救回丢失的Raid Set请和我们的工程师联系寻求技术支持。8、设定Volume Set功能 8.1Create Volume Set1.选选左方的Create Volume Set，会进入“Select The RAID Set To Create On it”画面，系统会自动检测到现有的Raid Set并显示在画面上。2.选择所要的Raid Set后，按Submit执行。3.设定相关选项：Volume Name：设定Volume Name(最多15个字节)，预设的Volume Name以Vol- ume Set#显示。Raid Level：利用下拉菜单，选取Raid LevelCapacity：系统会显示最大的容量，使用者可以自动设定容量大小。Creater Two TB Volume Support：当容量超过2TB时，此选项即会出现，使用者可以选择(No：则volume不可超过2TB)；(64bit LBA：使用在UNIX或Linux上)；(For Windows：使用在Windows上)。Initialization Mode：可前景执行(Foreground mode)或背景执行(background mode)Stripe Size：RAID 3不能变更Stripe Size。Cache Mode：可选择透过控制器的缓冲存储区(write-back cache)或等资料写入硬盘后回覆(write-through cache)。Tagged Command Queuing：可选择执行指令可(Enable)或否(Disable)。Max SCSI Speed：最大传输速率为320MB/sec。SCSI Channel：可选择单或双SCSI Channel。SCSI ID：选择值：0-15。SCSI Lun：选择值：0-7。8.2 Delete Volume Set1.要删除Volume Set，选选左方的Delete Volume Set，会进入“Select The Volume Set toDelete”画面，系统会自动检测到现有的Volume Set并显示在画面上。2.选选所要删除的Volume Set。3.选选Confirm The Operation后，按Submit执行删除Volume Set的设定。8.3Modify Volume Set1.选选左方的Modify Volume Set，选择所要变更的Volume Set后，按Submit执行。2.变更相关选项：Volume Name、Raid Level、Capacity、Initialization Mode、Stripe Size、Cache Mode、Tagged Command Queuing、Max SCSI Speed、SCSI Channel SCSI ID、SCSI Lun。3.选选Confirm The Operation后，按Submit执行变更Volume Set的设定。8.3.1Volume Expansion当有新增的硬盘加入Raid Set中，可扩充至现有Volume的容量或另新增的Volume Set。要扩充现有Volume的容量，在Volume Capacity的选项填入Volume容量大小，选选Confirm The Operation后，按Submit执行扩充Volume Set的设定。8.3.2Volume Set Migration当Volume Set的RAID Level变更、strip size变更、新增硬盘到RAID Set中，VolumeStatus的状态会变更为Migrating。选选左方的RaidSet Hierarchy即可看见Volume Status。8.4Check Volume Set1.选选左方的Check Volume Set，选择所要确认的Volume Set后，选选Confirm The Operation后，按Submit执行确认Volume Set的设定。2.选选左方的RaidSet Hierarchy即可看见Volume Status变更为Checking。8.5Stop Volume Set Check可利用此选项停止Volume Set Check。9、设定Physical Drive功能9.1Create Pass-Through Disk建立一个单独的硬盘，不具备RAID的功能。1.选选左方的Pass-Through，会进入“Select The IDE drive For Pass Through”画面，系统会自动检测未设定Raid Set的硬盘会且显示在画面中。2.设定相关选项：Cache Mode：可选择透过控制器的缓冲存储区(write-back cache)或等资料写入硬盘后回覆(write-through cache)。Tagged Command Queuing：可选择执行指令可(Enable)或否(Disable)。Max SCSI Speed：最大传输速率为320MB/sec。SCSI Channel：可选择单或双SCSI Channel。SCSI ID：选择值：0-15。SCSI Lun：选择值：0-7。3.完成设定后，选选Confirm The Operation后，按Submit执行设定Pass-Through硬盘的设定。9.2Modify Pass-Through Disk1. 选选左方的Modify Pass-Through，变更相关选项：Cache Mode、Tagged Command Queuing、Max SCSI Speed、SCSI Channel、SCSI ID、SCSI Lun。2.选选Confirm The Operation后，按Submit执行变更Pass-Through的设定。9.3Delete Pass-Through Disk选择左方的Delete Pass-Through,选择所要删除的Pass-Through Disk.1、 选择Confirm The Operation后，按Submit执行删除Pass-Through的设定。9.4Identify Selected Drive为了避免抽到错误的硬盘，可利用此灯功能来试别个别硬盘的相对位置。1、 选择左方的ldentify Drive,会进入“Select The IDE Device For ldentiflcation”书面，系统会自动侦测到您所选择的硬盘。2、 选择要试别的硬盘，接Submit执行选择功能。10System Configuration10.1System Configuration1.选择左方的System Config，设定查关选项。System Beeper Settong:设定蜂鸣声关或开。Raid Rebuild Priority: 设定资料重建。Rerminal Port Configuration：设定传输速率及停止们元。传输速率预设值为115200，停止位元预设值为1bit.JBOD/RAID Configuration：选择JBOD或RAID。Maximun SATA Mode Supported：可选择SATA150，SATA150+NCQ，SATA300，SATA300+NCQ。Disk write cache mode:可选择auto enabled,disabled.当选择auto时，如系统有安装偌援电池（battery backup module）时，则为启动（enabled）为入硬盘的缓冲。（Disk Capacity Truncation Mode：当使用者需要将不同产牌的硬盘互相援时，可选择此功能将硬盘的容量去除尾数，增加容性。Multiples of 10G:去除硬盘个位数的尾数，如123.5GB，则执行此功能后为120GB。Multiples of 1G: 去除硬盘个位数的尾数，如123.5GB，则执行此功能后为123GB。10.2U320 SCSI Target Config 选择左方的U320SCSITarget Config,可选择关启或开关快速选择（QAS）10.3EtherNet Config选择左方的EtherNet Config,设定查关乙太网络选项。10.4 Alert By Mail Config选择左方的Alert By Mail Config,可设定当系统有不正常的情况发生时，传送