MIL-STD-810G军标测试.xls

Test itemsMIL-STD-810G 501.5 Procedure I - Storage. 501.5 Procedure II - Operation. 502.5 Procedure I - Storage. 502.5 Procedure II - Operation. Temperature Shock 503.5 Procedure I-B Rain 506.5 Procedure I - Rain and Blowing Rain. Low Temperature High Temperature Humidity 507.5 Procedure II Aggravated Cycle Sand and Dust 510.5 Procedure I - Blowing Dust Immersion 512.5 Procedure I -Immersion 514.6 Procedure I - General vibration. Category 4 - Truck/Trailer - Secured Cargo. 514.6 Procedure I - General vibration. Category 8 - Aircraft-propeller. Shock 516.6 Procedure III - Fragility. Vibration Confirm conditions Procedure I - Storage. Seven 24-hour cycles，Total 168hours. Humidity no need control Basic hot-Table 501.5-II. Induced Conditions Procedure II - Operation Three 24-hour cycles，Total 72hours Humidity no need control Basic hot-Table 501.5-II. Ambient Air Conditions Procedure I - Storage. a.Nonhazardous or non-safety-related (non-life- support type) materiel:4hours Basic cold (C1)-Table 502.5-I. Induced Environment Procedure II - Operation. a.Nonhazardous or non-safety-related (non-life- support type) materiel:4hours Basic cold (C1)-Table 502.5-I. Ambient Air Procedure I-B Single cycle shock from constant extreme temperature. Figure 503.5-2.- transfer rate 1minute max. 1cycle ,30min for Low and 30min for High Low temperature： -33 High temperature：63 Procedure I - Rain and Blowing Rain. 1.Handset temperature 10 C Higher than water 2.Exposure duration:30 minutes. Procedure II Aggravated Cycle 3060 95%RH，10days Figure 507.5-7 and Table 507.5-IX Procedure I - Blowing Dust.( 150 m). Dust composition.:140 mesh Silica Flour（100 percent less than 150m, 50 percent of 20 5 m.） 6 hours at standard ambient temperature, and an additional 6 hours at the high temperature（Basic hot 43） same as IP6X Procedure I -Immersion Depth of complete immersion:10.1m(measured from the uppermost surface of the test item to the surface of the water) Duration of immersion:30 minute 10 C above the water temperature(normal water temperature,Standard Ambient) Procedure I - General vibration. Category 4 - Truck/Trailer - Secured Cargo. 1. Truck transportation over US highways -refer to Figure 514.6C-1 and Table 514.6C-II. 2.Exposure durations. 60 minutes per axis Procedure I - General vibration. Category 8 - Aircraft - propeller. Exposure durations： one hour per axis Procedure III - Fragility. 1.Trapezoidal shock pulse 2.Drop height (h)：76cm 3.maximum acceleration level (Am)：15gs. 4.one shock per axis Please refer to Figure 516.6-11 MIL-STD-810G军标测试试验要求军标测试试验要求 1.只要求做高温储存，7个24-hours循环 2.温度为3063循环温度,24 hours 一个循环,详 见Table 501.5-II. Induced Conditions 1.只要求做高温工作，3个24-hours循环 2.温度为3043循环,24 hours 一个循环,详见 Table 501.5-II. Ambient Air Conditions 1.只要求做低温存储,4h 2.恒定温度-33 1.只要求做低温工作,4h 2.恒定温度-21 1.Thermal shock 曲线如下： 试验需要满足的条件及参数如下： 1.recommend a minimum rate of rainfall rate:1.7 mm/min 2.Handset temperature 10 C Higher than water 3.droplets diameter from 0.5mm to 4.5mm 4.the drops approach terminal velocity :about 9m/s 5.horizontal wind velocities equal to and exceeding 18 m/s. 6.Exposure duration:30 minutes. 7.Test Facility:Figure 506.5-1 1.温度范围3060 ,相对湿度954% 2.24-hour 一个cycle,曲线如下: 1.Relative humidity (RH) ：at 30 percent or less Air velocity:1.5 1 m/s to 8.9 1.3 m/s Dust concentrations.:10.6 7 g/m3 Dust composition:140 mesh Silica Flour（100 percent less than 150m, 50 percent of 20 5 m.） 6 hours at standard ambient temperature(23), and 6 hours at the high storage or operating temperature.(43) 样品温度需高于水温10 军标要求及实验参数 1.使用标准实验室振动激励器(振动台)、滑台、夹 具 2.试验参数:10-500Hz, 1.04Grms vertical, 0.204Grms transverse,