博科安装手册.doc

博科 200E/300/4100/5000/5100 安装手册一、交换网络配置注意：建立console连接，交换机的默认IP地址为71、通过交换机的串口建立console会话.在Windows 95,98.2000,或者NT的环境中：（超级终端）Bits per second: 9600每秒位数为9600Databits: 8数据位为8Parity: None奇偶校验Stop bits: 1停止位Flow control: None数据流控制登陆到交换机2、在登陆后，首先修改管理员密码.login:adminPasswd:password原账号密码Change passwords as follows:adminPassword: Customer assigned新账号密码（用户自己定义）3、给交换机分配IP地址，子网掩码和默认网关等信息switch:admin ipaddrsetEthernet IP Address 7:7以太网IP地址Ethernet Subnetmask :以太网子网掩码Fibre Channel IP Address :Fibre Channel Subnetmask :光网的IP地址和掩码Gateway IP Address :默认网关Set IP address now? y = set now, n = next reboot:y确认修改IP address being changed.Committing configuration.Done.修改成功switch:admin4、验证交换机网络信息：admin ipaddrshow5、重新加载交换机并且关闭串口console会话.:admin reboot:admin exit确认交换机POST完全加载成功6、开始通过telnet登陆交换机.# telnet 二配置交换机基本参数1、配置交换机的名字：admin switchname“”2、设置日期和时间：admin date 月，日，小时，分钟，年switch:admin dateFri May 5 21:50:00 UTC 1989switch:adminswitch:admin date 0624165203Tue Jun 24 16:52:30 UTC 2003switch:admin3、设置客户需要的时区：:admin help tstimezone例如：:admin tstimezone -8,0(ie GMT-0800):admin tstimezone +8,0(北京时间)4、禁止交换机更改fabric参数.（如果交换机要连接到其他的交换机上，这一步必须做，如果不是，你可以忽略4,5,6步骤）:admin switchdisable:admin configureConfigure.Fabric parameters (yes, y, no, n): no y5、设置交换机Domain ID.（每个SAN交换机独一无二的数字）Domain: (1.239) 16、允许交换机修改fabric参数.:admin switchenable三、配置交换机的ZONES1、确定所有的主机HBAs和存储设备都已经连接上了交换机.:admin switchshow(查交换机的domain ID)switch:admin switchshowswitchName: sw0switchType: 66.1switchState: OnlineswitchMode: NativeswitchRole: SubordinateswitchWwn: 10:00:00:05:1e:57:b3:06 switchDomain: 1switchId: fffc02zoning: OFFswitchBeacon: OFFFC Router: ONFC Router BB Fabric ID: 128Index Port Address Media Speed State Proto=0 0 020000 id N4 No_Light FC1 1 020100 id N4 In_Sync FC Disabled2 2 020200 id N4 No_Light FC3 3 020300 id N4 No_Light FC4 4 020400 id N4 Online FC F-Port 1 N Port + 1 NPIV public5 5 020500 id N4 Online FC F-Port 1 N Port + 1 NPIV public6 6 020600 id N4 Online FC F-Port 1 N Port + 2 NPIV public7 7 020700 id N4 Online FC F-Port 1 N Port + 1 NPIV public8 8 020800 id N4 Online FC F-Port 10:00:00:05:1e:65:95:819 9 020900 id N4 Online FC E-Port 10:00:00:05:1e:40:ff:95sw0 (upstream)(Trunk master):admin nsshow:admin nscamshow2、模块#1：用web工具配置交换机的Zoneshttp:/（安装JRE 1.6，打开IE浏览器）*点击“Zone Admin”按钮3、模块#2：配置Zones通过telnet会话（用CLI）#telnet login: adminpassword: passwordDomain 1Eng HostMkt HostS1S2S3S4S51）创建 Aliases alicreate “Eng_Host”,“1,0”alicreate “Eng_Stor”,“1,4; 1,5”alicreate “Mkt_Host”,“Mktwwn”alicreate “Mkt_Stor”,“s3wwn; s4wwn; s5wwn”2)创建 Zoneszonecreate “Zone_Eng”,“Eng_Host; Eng_Stor”zonecreate “Zone_Mkt”,“Mkt_Host; Mkt_Stor”3)创建 Configurationcfgcreate “Cfg_EngMkt”,“Zone_Eng; Zone_Mkt”sw4100:admin cfgshowDefined configuration:定义配置： cfg: Cfg_EngMkt Zone_Eng; Zone_Mkt zone: Zone_Eng Eng_Host; Eng_Stor zone: Zone_Mkt Mkt_Host; Mkt_Stor alias: Eng_Stor 1,4; 1,5 alias: Eng_Host 1,0 alias: Mkt_Stor 21:00:00:20:37:87:49:29; 21:00:00:20:37:87:e5:20;21:00:00:20:37:87:20:c5 alias: Mkt_Host 21:00:00:20:37:87:23:e2Effective configuration:生效的配置： no configuration in effect 没有配置是有效的4) 激活配置文件 cfgenable “Cfg_EngMkt”switch:admin cfgenable “Cfg_EngMkt”You are about to enable a new zoning configuration.This action will replace the old zoning configuration with thecurrent configuration selected.Do you want to enable Cfg_EngMkt configuration (yes, y, no, n): no yzone config Cfg_EngMkt is in effectUpdating flash .sw4100:admin cfgshowDefined configuration: cfg: Cfg_EngMkt Zone_Eng; Zone_Mkt zone: Zone_Eng Eng_Host; Eng_Stor zone: Zone_Mkt Mkt_Host; Mkt_Stor alias: Eng_Stor 1,4; 1,5 alias: Eng_Host 1,0 alias: Mkt_Stor 21:00:00:20:37:87:49:29; 21:00:00:20:37:87:e5:20;21:00:00:20:37:87:20:c5 alias: Mkt_Host 21:00:0