AB变频器快速调试.doc

编辑参数如下1. 上电时LCD显示器显示为:Output Freq S0.00Hz 按一次SEL键显示组参数编号及字母.按上下键改变组菜单(Basic Display:b基本显示.Basic Pr0gram :P基本编程.Terminal Block:T端子.Communications:C通信.Advanced progran:A高级编程，Aux Relay Cord: R=Aux Relay Card.Advanced Display:d高级显示)。2. 按SEL键进入某组菜单，该组中上次查看时的参数编号将会闪烁。按上下键可选择主菜单功能，先选择基本显示(Display Groupb)参数按下SEL进入:b001:输出频率 002：命令频率003：输出电流 ：004输出电压 005：直流母线电压006：变频器状态 007：故障代码1 008：过程显示 010：输出功率 011：已用电MVV 012：运行时间 013：转矩电流 014：变频器温度 015：已用电KW 以上参数是变频器自动默认不用修改。3. 按上下键可选择主菜单功能，先选基本编程Basic Progran Group按下SEL进入注：这些参数要根据实用的值来进行设定 P031：motor NP Volts(电动机铭牌电压) P032：motor NP Hertz (电动机铭牌频率) P033：motor OL current(电动机额定电流 )P034：minimum Freq(最小频率 )0.00Hz P035：maximum Freq(最大频率)50HZ P036：Start Source(起动源)2-wire 002 P037：Stop mode(停止模式)coast 005 P038:Speed Reference(速度基准值)Analog in1 002 P039:Accel Timel(加速时间为15秒)Sec P040：Decel Timel(减速时间为10秒)Sec P041：Reset to Defalts复位为默认值工Ready/Zdle 000 P042：Auto mode(自动模式) NO Function 003 P043：Motor OL Ret(电机过载值存储)Disabled 0004. 按上下键可选择主菜单功能，先选端子 Terminal Block Group按下SEL进入T051:Terminal Block(数字量输入1选择) Digital in1 sel T052:Digital In2 sel(数字量输入2选择)Local 003 T053:Digital In3 sel(数字量输入3选择) Clear Fault 010 T054:Digital In4 sel(数字量输入4选择) Comm port 004 T055:Relay out1 sel (继电器输出1选择)Ready/Fault 000 T056:Relay out1 Level (继电器输出1幅值)0.00 T058:Relay 1 on Time(继电器1接通On时间)0.00 sec T059:Relay 1 off Time(继电器1断开Off时间)0.00 sec T060:Relay out 2 sel(数字量输出2选择) motor Running 002 T061:Relay out 2 Level (继电器输出2幅值)0.00 T063:Relay 2 on Time(继电器2接通On时间)0.00 sec T064:Relay 2 off Time(继电器2断开Off时间)0.00 sec T065: Opto out sel (光电耦合输出选择)At Frequency 001 T066: Opto out Level(光电耦合输出幅值)0.00 T068: Opto out Logic (光电耦合输出逻辑) 0.00 T069: Analog In 1 Sel(模拟量输入1选择) 4-20mA 001 T070: Analog In 1 LO(模拟量输入1下限) 0.0% T071: Analog In 1 Hi(模拟量输入1上限)100.0% T072: Analog In 1 Loss(模拟量输入1丢失)Disabled 000 T073: Analog In 2 Sel(模拟量输入2选择) 0-10V 002 T074: Analog In 2 LO(模拟量输入2下限) 0.0% T075: Analog In 2 Hi(模拟量输入2上限)100.0% T076: Analog In 2 Loss(模拟量输入2丢失)Disabled 000 T077: Sleep-wake sel (休眠-唤醒选择) Disabled 000 T078: Sleep-Level (休眠等级) 10% T079: Sleep-Time (唤醒时间) 0.0 SEC T080: wake-Level (唤醒等级) 15% T081: wake-Time (唤醒时间) 0.0 SEC T082:Analog out 1 sel (模拟量输出1选择) outFreq 0-10V 000 T083:Analog out 1 High (模拟量输出1上限)100% T084:Analog out 1 setpt(模拟量输出1设定点)0.0% T085:Analog out 2 sel (模拟量输出2选择) outcurr 0-10V 001 T086:Analog out 2 High (模拟量输出2上限)100% T087:Analog out 2 setpt(模拟量输出2设定点)0.0% T088:Anlg Loss Delay (模拟量丢失延时)0.0 SEC T089:Analog In Filter (模拟量输入上限)05. 按上下键可选择主菜单功能，先选通信语言Communications Group按下SEL进入 C101:Language(通信语言)001 EnglishC102:Comm Format(通信格式)C103:Comm Data Rate(通信数据速率)003 9600C104:Comm Node Addr(通信节点地址)C105:Comm Loos Action(通信丢失动作)C106:Comm Loos Time(通信丢失时间)C107:Comm Write Mode(通信写模式)C108:Start Source2(通信起动命令源2)6.按上下键可选择主菜单功能，先选高级编程Advanced Program Group 按下SEL进入 A141:Advanced Program Group(消防强制输入频率)Purge Frequency A142:Internal Freq(内部频率)60HzA143:Preset Freq0(预置频率0)0.0HzA144:Preset Freq1(预置频率1)5.0HzA145:Preset Freq2(预置频率2)10.0HzA146:Preset Freq3(预置频率1)20.0HzA147:Accel Time 2(加速时间2)30.00 SecA148:Decel Time 2(减速时间2)30.00 SecA149:S Curve%(S曲线%)20%A150:PID Trim Hi(PID整定上限)60HZA151:PID Trim LO(PID整定下限)0.0HZA152:PID Ref sel(PID基准值选择)PID setpoint 001A153:PID Feedback sel (PID反馈值选择)Anaiog In1 000 A154:PID Prop Gain(PID比例增益) 1A155:PID Integ Time(PID积分时间)10.0 SscA156:PID Diff Rate(PID微分速率)0.00 1/SecA157:PID Setpoint(PID设置点)50%A158:PID Deadband(PID死区)0.0%A159:PID Preload(PID预负载)0.0HZA160:PID Process Factor(PID过程因数)30.0A163:Auto Rstrt Tries(自动重新起动尝试)0A164: Auto Rstrt Delay(自动重新起动延时)1.0 SecA165:Start At PowerUp (上电起动)Disabled 000 A166:Reverse Disable (反向禁止)REV Disabled 001A167:Flying Start En (飞速起动使能)Disabled 000A168:Pwm Frequency(PWM频率) 4.0KHzA169:Pwm Mode(PWM模式) 2-Phase 001A170:Boost select(升压选择)45.0VT 004A171:Start Boost(起动升压) 2.5%A172:Break Voltage(转折电压)25%A173:Break Frequency(转折频率)15.0HzA174:Maximum Voltage(最大电压)460 VACA175:slip Hertz FLA(满载滑差频率补偿)2.0HzA176:DC Brake Time(直流制动时间)0.0 SECA177:DC Brake Level(直流制动幅值)A178:DC Brk TimeStrt(起动时直流制动时间)0.01SECA179:Current Limit 1(电流限幅1)A180:Current Limit 2(电流限幅2)A181:Motor Select(电动机过载选择)A182:Drive OL Mode(变频器过载模式)A183:SW Current Trip(软件电流跳闸)A184:Load Loss Level(负载丢失幅值)A185:Load Loss Time (负载丢失时间)A186:Stall Fault Time (堵转故障时间)A187:Bus Reg Mode (总线调节模式)A188:Skip Frequency1(跳变频率1)A189:Skip Freq Band1(跳变频率宽带1)A190:Skip Frequency2(跳变频率2)A191:Skip Freq Band2(跳变频率宽带2)A192: Skip Frequency3(跳变频率3)A193:Skip Freq Band3(跳变频率宽带3)A194:Compensation(补偿)A195:Reset Meters(测量复位)A196:Testpoint Sel(测试点选择)A197:Fault Clear(故障清除)A198:Program Lock (编程锁定) A199:Motor NP Poles(电动机铭牌极对数)A200:Motor NP FLA(电动机铭牌电流)7.按上下键可选择主菜单功能，先选辅助继电器Aux Relay Card Group 按下SEL进入 R221:Relay Out3 Sel (继电器输出3选择) R222:Relay Out3 Level (继电器输出3幅值) R224:Relay Out4 Sel (继电器输出4选择) R225:Relay Out4 Level (继电器输出4幅值) R227:Relay Out5 Sel (继电器输出5选择) R228:Relay Out5 Level (继电器输出5幅值) R230:Relay Ou63 Sel (继电器输出6选择) R231:Relay Out6 Level (继电器输出6幅值) R233:Relay Out7 Sel (继电器输出7选择) R234:Relay Out7 Level (继电器输出7幅值) R236:Relay Out8 Sel (继电器输出8选择) R237:Relay Out8 Level (继电器输出8幅值) R239:Aux Motor Mode (辅助电机模式) R240:Aux Motor Qty(辅助电机数量) R241:Aux 1 Start Freq(辅助1起动频率) R242:Aux 1 Stop Freq(辅助1停止频率) R243:Aux 1 Ref Add(辅助1频率增加) R244:Aux 2 Start Freq(辅助2起动频率) R245:Aux 2 Stop Freq(辅助2停止频率) R246:Aux 2 Ref Add(辅助2频率增加) R247:Aux 3 Start Freq(辅助3起动频率) R248:Aux 3 Stop Freq(辅助3停止频率) R249:Aux 3 Ref Add(辅助3频率增加) R250:Aux Start Deiay(辅助起动延时) R251:Aux Stop Deiay(辅助停止延时) R252:Aux Prog Delay(辅助控制延时) R253:Aux AutoSwap Tme (辅助自动切换延时) R254:Aux AutoSwap Lvl (辅助自动切阀值) 8.按上下键可选择主菜单功能，先选辅助继电器Advanced Display Group 按下SEL键进入 d301:Control Source(控制源) d302:Control Source(控制输入状态) d303:Comm Display Group(通讯状态) d304:PID Setpnt Displ(PID设定点显示) d305: