摘要.doc

0041-活门冲孔落料工艺及级进模设计【全套12张CAD图】

收藏

资源目录
跳过导航链接。
压缩包内文档预览:
预览图 预览图
编号:30580927    类型:共享资源    大小:865.44KB    格式:ZIP    上传时间:2019-12-12 上传人:机****料 IP属地:河南
50
积分
关 键 词:
全套12张CAD图 0041 活门 冲孔 工艺 级进模 设计 全套 12 CAD
资源描述:
0041-活门冲孔落料工艺及级进模设计【全套12张CAD图】,全套12张CAD图,0041,活门,冲孔,工艺,级进模,设计,全套,12,CAD
内容简介:
活门冲压工艺及级进模具设计摘 要:本设计题目为活门件冲裁模,体现了典型冲裁模的设计要求、内容及方向,有一定的设计意义。通过对该模具的设计,加强了设计者对冲裁模设计基础知识的理解和运用,为设计更复杂的冲裁模具做好了铺垫。本设计运用冲裁工艺及模具设计的基础知识,首先分析了板材的性能要求,为选取模具的类型做好了准备;然后计算了冲裁件的冲裁力,便于选取压力机吨位及确定压力机型号;最后分析了冲裁件的特征,便于确定模具的设计参数、设计要点及卸件装置。本设计采用了冲孔落料级进模成形活门制件。成形原理可划分为两个阶段:首先冲孔凸模与凹模共同作用先冲出活门制件上的孔,而后利用第一步冲出的两个10mm的半圆孔做精确定位使外形凸模与凹模共同作用使工件落料成形。关键词: 冲孔落料级进模 冲孔凸模 凹模 压力机吨位 The valve ramming craft and the level enter the mold design Abstract: This design topic for the valve punching die, has manifested the typical punching die design request, the content and the direction, has certain design significance.Through to this mold design, strengthened the designer to the punching die design elementary knowledge understanding and the utilization, for designed the more complex blanking mold to complete the upholstery.This design the elementary knowledge which designs using the blanking craft and the mold, first has analyzed the plate performance requirement, for selected the mold the type to prepare for; Then has calculated the blanking blanking force, is advantageous for the selection press tonnage and the definite press model; Finally has analyzed the blanking characteristic, is advantageous for determines the mold the design variable, the design main point and the shedder.This design used the punch holes - to fall the material level to enter the mold forming valve workpiece.The formed principle may divide is two stages: First the punch holes raised mold and the concave mold affect together run out on the valve workpiece first the hole, after but uses two 10mm half round hole which first step runs out to make the pinpointing to cause the contour raised mold and the concave mold affects together causes the work piece to fall the material forming.Key word: The punch holes -
温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
提示  人人文库网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。
关于本文
本文标题:0041-活门冲孔落料工艺及级进模设计【全套12张CAD图】
链接地址:https://www.renrendoc.com/p-30580927.html

官方联系方式

2:不支持迅雷下载,请使用浏览器下载   
3:不支持QQ浏览器下载,请用其他浏览器   
4:下载后的文档和图纸-无水印   
5:文档经过压缩,下载后原文更清晰   
关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

网站客服QQ:2881952447     

copyright@ 2020-2025  renrendoc.com 人人文库版权所有   联系电话:400-852-1180

备案号:蜀ICP备2022000484号-2       经营许可证: 川B2-20220663       公网安备川公网安备: 51019002004831号

本站为文档C2C交易模式,即用户上传的文档直接被用户下载,本站只是中间服务平台,本站所有文档下载所得的收益归上传人(含作者)所有。人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。若文档所含内容侵犯了您的版权或隐私,请立即通知人人文库网,我们立即给予删除!