BF01148160.pdf_第1页
BF01148160.pdf_第2页
BF01148160.pdf_第3页
全文预览已结束

BF01148160.pdf.pdf 免费下载

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

chambers; to assess the bending stresses in the seal strips; and, to optimize the geometric parameters of the seal from the standpoint of its cost and strength characteristics. i. 2. , 4. LITERATURE CITED I. I. Kirillov, Theory of Turbomachinery in Russian, Mashinostroenie, Moscow-Leningrad (1964). L. A. Serovskii, On one method of calculating the thermodynamic properties of compress- ible gases and their mixtures, Materials Presented at the Seventh All-Union Conference on Compressor Construction in Russian, Leningrad. Politekh. Inst., Leningrad (1983), pp. 3-5. Methods of Calculating the Thermophysical Properties of Gases and Liquids in Russian, Khimiya, Moscow (1974). N. P. Vukalovich and N. I. Novikov, Thermodynamics in Russian, Mashinostroenie, Moscow (1972). IMPROVING THE EFFICIENCY OF COOLING SYSTEMS USED IN COMPRESSORS V. P. Parfenov, P. A. Milshtein, and V. A. Myshenko bC 621.512 One of the critical needs in the compressor industry is to improve the cooling systems used in compressors and compressor stations (CACS). This is because of three main problems: the existing cooling systems are unable to maintain high and stable techoeconomic perform- ance parameters during operation of the compressors; a considerable amount of heat is lost during operation of the compressors.which is practically equal to the work done; and the cooling systems of the compressor station require a large amount of water (about 55 million ma/day). Improvement of cooling systems for CACS should be taken up after considering various design factors which determine the efficiency of the system (design of the heat-exchange equipment and cooling system as a whole), as well as the operating conditions (climate, dirt level, system reliability, etc.). The cooling systems for CACS should meet the following requirements: high efficiency during prolonged operation of the CACS; utilization of compression heat; low water consump- tion; high reliability of the CACS; desired level of dehumidification of the compressed air (for pneumatic systems used in machine building, chemical, mining and other industries, railway rolling stock,etc.). These requirements are best met by using heat-exchange equipment (HE) 4 (see Pig. I) and systems with different combinations of cooling media for the interstage and final cool- ing of the compressed gas. The feature of such systems is that stagewise cooling of compressed gas is carried out with various media depending upon the operating conditions, waste heat utilization options, design of the CACS, etc. Thus, when the consuming points are near it is preferable to use the high-potential heat (20-25%of the heat removed by the coolers) for heating the compressed air and increas- ing its energy. In practice, this can be achieved in the waste-heat utilization sections 7 (see Fig. la, c) located immediately after the compression stages i, 2, 3 of the compressor. The other part of the compression heat (60-70%) can be used, during the cold part of the year, for heating the compressor station premises with fresh air heated in the air-cooled sections 5. In these cases, final cooling of the compressed air to the desired temperature is per- formed in the water-cooled sections 6 where 5-15% of the total heat is removed. The water flow through the water-cooled sections can be regulated depending upon the weather conditions. For example, reduction in ambient air temperature will reduce the need for cooling in the Translated from Khimicheskoe i Neftyanoe Mashinostroenie, No. i, pp. 26-27, January, 1990. 42 0009-2355/9050 ?9 1990 Plenum Publishing Corporation i f d f F 9 F 7 a 2 2 $ ,9 b ,f 7 ,f 6 .f 1+ F 2 F $ 4 6(9) . / - 8 8 8 d Fig. 1. Compressors with combined heat-exchanger systems (a, b, c, d) for cooling of compressed air: 1, 2, 3) compression stages; 4)heat exchange systems; 5, 6) air-cooled and water-cooled sections, of the cooling system, respectively; 7, 8) waste heat re- covery section for heating compressed gas and inter- mediate heat transfer medium, respectively; 9) brine section. final stage. Thus, cooling water will not be required at all during some parts of the year. If it is necessary to ensure fully automatic operation of the CACS (without water con- sumption, as in the case of mobile compressor stations), final cooling of the compressed gas can be performed with the help of a refrigerating machine (RM) in the brine sections 9 (see Fig. Ib), or directly in the evaporator RM. Use of such sections is also desirable for deeper cooling (to a lower temperature) of compressed air to ensure dehumidification (see Fig. Ic, d). The first three variants of the heat exchanger (Fig. la, b, c) have air-cooled sections. These have limited utility for large centrifugal compressors (K-500, K-250) because of their complexity. IN such cases it is preferable to use heat exchangers with intermediate heat transfer media and dispense with the air-cooled sections (Fig. id). In the latter design the bulk of the heat (85-95%) is transferred to the intermediate heat transfer medium in the first section 8 for further use, while final cooling is performed in the second section 6 with the help of recycled water, or some other cooling medium. Thus, by using cooling media in different combinations it is possible to reduce cool- ing water consumption by a factor of 10-15. The extent of cooling of compressed gas by this combined method is not less than that with water cooling in summer, while in winter the cooling effect can be even higher as the air-cooled sections will play a dominant role. Moreover, the lower heat load in the water-cooled sections of the combined system reduces the effect of deposits and dirt on the cooling-water surfaces of the heat exchangers. The rate of formation of such deposits will also be less, because of the significantly lower initial temperature of the compressed air in the water-cooled section (50-60 This en- sures more stable cooling of the compressed air in the water-cooled section and reduces costs associated with frequent cleaning of the cooling system. Compactness of the heat-exchange equipment is an important consideration. This has been achieved by using ribbed-plate heat exchangers (RHE) developed at the All-Union Scientific Research Institute for Compressors, or multi-section tubular gas-coolers 1-3. 43 The choice of heat-exchanger depends on the operating conditions, design features of the CACS, and potential users of waste heat. The highest efficiency of the heat ex- change system is achieved in each specific case by resolving a multi-variant problem of technoeconomic optimization, involving optimum distribution of heat load between the cooling sections, optimization of the cooling conditions, optimization of the design parameters of the heat exchanger surfaces in each section, etc. The research carried out at the Omsk Design Institute and the All-Union Scientific Research Institute for Compressors has helped to identify the preferred heat exchanger de- signs and determine the relationship between the design parameters of the cooling sections and cooling conditions. Thus, for example, a range of standardized ribbed-plate heat ex- changer systems based on the first and third variants for intermediate and final cooling of compressed air has been

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论