服装QC评语.doc

服装qc评语英文对照1 approved swatch 已批的布办 art. no./style no. 款号 autolock zipper 自动锁拉链 back stitches 回针/返针 bad joined stitches 驳线不良 broken hole 破洞 broken stitches 断线 broken yarn 断纱 bubbling 起泡 bump at placket edge 筒边钮门位不顺直 center back rides up 后幅起吊 checks / stripes not match 格仔/条子不对称 collar points hi / low 领尖高低 color fading 褪色 color fastness problem 褪色问题 color fibre woven in 杂色纤维织入 color shading 色差 color thread left inside 藏色线 color too dull / bright 颜色太哑/闪 color yarn 色纱 combi program 配色组合 contrast color 撞色 crease mark 折痕 crocking test 摩擦测试 crossed back vent 背叉搅 cuff edge not leveled 鸡英边高低 dirty dot （较小的）污点 dirty mark 污渍 dirty spot （较大的）污点 drop test 跌落测试 dry rub 干擦 excess extension 突咀 fabric defect 布疵 fabric too closed to zipper 面布车得太贴近拉链 flap stricking up 袋盖反翘 fluo.=fluorescence 荧光 flying up 飞起，翘起 fty.sticker 工厂的贴纸 gapping 藏木虱（烫工） glaze mark （熨烫）起镜 hem not leveled 高低脚 hi / low pocket 高低袋 hiking at bottom of placket 前筒吊脚 hiking up 起吊 horizontal seam not leveled 水平缝骨不对称 inner cuff visible 介英反光 iron mark 烫痕 knot 结头 lastest size specification 最新的尺寸表 lining too full / tight 里布太多/太紧 major defect 大疵 match color 配色 material defect 物料疵点 minor defect 小疵 mixed color yarn 色纱 neck drop pucker 筒顶起皱 needle damage 针损坏布料 needle hole * off grain 布纹歪 oil stain 油渍 open seam 爆口 overlapped collar 叠领，踏领 overlapped lips 叠唇 overpress 熨烫过度 overwash 洗水过度 placket bottom spread open 筒脚张开 placket wavy 前筒起蛇（皱） pleated sewing 打褶 pocket opening spray open 口袋“笑口” poor back-stitches 回针不佳 poor ironing 烫工不良 pressing mark 压痕 previous shipment 以前走的货 production status 生产情况 pucker 起皱 qc sticker qc贴纸，“鸡纸” raw edge 散口 run off stitches (车缝）落坑 printing scrimp 印花裂痕 seam overturn 止口反骨 sewn in waste 车缝时混有杂物 shading garment to garment 衫与衫之间色差 shading within 1pcs garment 衣服裁片色差 shipment under consignment 寄卖 short shipment 短装 skipped stitches 跳线 slanting pocket 歪袋 slub 毛粒 smiling pochet 袋“笑口” sticker 贴纸 stitches not in seam shadow 缝线没被盖住 stripes/checks not matching 不对条/格 sub-contractor 外发厂 substitute fabric 代用布 support sitches visible 辅助线外露 fabric swatch 布办 tension 张力 thick yarn 粗纱 toppest placket pucker 筒顶起皱 total different color 颜色完全不同 trapped color thread 藏色线 twist 扭 twist leg 扭髀 uncut thread ends 线头 under stitches visible 底线露出 underply turn out 反光 underply visible outside 反光 underpress 熨烫不够 undesireable odor 臭味，不可接受的气味 uneven collar 歪领 uneven color 深浅色 uneven length of placket 长短筒 uneven length of sleeve 长短袖 uneven lips 大小唇 uneven stitching density 针步密度不均匀 unmatched crotch cross 下裆十字骨错位 unmeet back vent 背叉豁 wet rub 湿擦 wrong combo 颜色组合错误 wrong pattern 图案错误 wrong size indicated 错码 yarn drawn out 抽纱 zipper not movable 拉链不能拉the out-come / appearance of the frills of sealing sample is not acceptable, it looks very flat / dead, must be more balanced / natural look as standard sample dd 28.8.02.前中荷叶边太死太平，不够生动，请以2002年8月28日的办做标准。sort out the major material defects.挑出严重布疵。take care for trimming + cleaning.留意剪线和清洁。string holes from plastic string ( for washing ) at pocket flap visible, must be removed.袋盖上有洗水时打的枪针洞，请消除。front horizontal seam not leveled.前幅横骨不对称。hand feel slightly softer than approved sample.手感比批办稍软。armhole pipping ( inside) 2mm more than sealing sample.夹圈滚条宽度比原办大了2mm。pls. add one more button for bigger sizes.请在大码的衣服上加多一颗钮扣。make sure inner facing is long enough in order to avoid pulling at placket bottom.确保襟贴足够长以避免前襟起吊。pay attn. the workmanship of ironing, dont press the seam too much and avoid the seam allowance see through by heavy pressing.注意烫工，骨位不要烫太重，避免缝骨止口起痕。center front collar not overlap but also not spray.领子前中不要重叠但也不要张开。bust dart seam allowance must be ironed upward.胸折止口要烫向上面。uneven width of top-stitches at closure edge.前襟边面线宽度不均匀。pls. add one more button for all sizes as the distance from hem is too big.请在所有尺码的衣服上加多一颗钮扣，因为离衫脚的距离太大。pls. fix pocket with movable stitches as sealing sample.请跟原办在口袋上车上(可拆去的)假缝线。the collar band must not visible at back when wear.衣服穿着时下级领不能外露。pls. make sure the collar are balanced on both sides.请确保领子两边对称。found 3 colors shade within 10 pcs!十件衣服中有三种色差!3 different color lots in color beige compare to the approved swatch: 3/10 pcs darker, 4/10 pcs lighter, 3/10 as swatch.beige色和色办相比有3种不同色差，其中3件偏深，4件偏浅，3件同色办。pay attention on the color, which within one garment must be in same color shade.注意颜色，一件衣服里不能有色差。due to the price reason, we accept this order with cutting both ways either in direction or against hair but you have to make sure the fabric direction must be always same with one garment.因为价钱问题，我们接受这个订单的可以顺毛裁和逆毛裁，但一定要确保一件衣服内的所有裁片是同一毛向。(灯心绒衣服)pls. cut all jackets against hair.所有夹克要逆毛裁。pls. close the pocket with several movable stitches ( must be not closed all, pls. leave 1cm at each side unstitching).请用在口袋上缝一段可拆除的假线(一定不能全部缝合，两边要各留1cm不缝合)stitching and seams 线步和骨位 1) raw edge 散口2) raw edges 爆口3) untrimmed thread ends 线头未剪4) skipped stitches 跳线5) exposed stitching 露线6) broken stitches 断线7) run-off stitches 间线落坑8) crooked stitches 线步弯曲9) poor join stitching 驳线欠佳10) unsightly over-lapping stitches 驳线不良11) stitches too loose 线步太松12) stitches too tight 线步太紧13) distorted stitches 车线不直14) broken seams 缝线爆幵15) expose stitch 落坑线外露16) inconsistent stitching 线步不一致17) uneven width on double stitching 双线阔窄不均18) uneven stitching density / tension 线步密度 / 松紧度不平均19) 1/4 top stitch not even 1/4面线有宽窄20) expose safety stitch 保险线外露21) inseam is uneven 内缝线不井齐22) merrow stitch density is too big 拨边线步太疏23) overlap stitch is not well 反缝的接线不好24) top & under stitch tension not match 底面线力不相符25) uneven merrow seam 内拨边线弯曲不直26) missing reinforcement stitches 漏车加固线步27) row of stitching missing top stitch 漏车一行线平车线28) stitch count less than standard 线步较标准少29) all top stitch is uneven 所有的面线都不均匀30) blind stitch is broken 筒针有断线现象31) blind stitch is wavy 筒线弯曲不直32) shoulder seam not smooth 小肩缝弯曲不直33) uneven folded width at bottom sweep 1/2hemming. 折车1/2脚围阔窄34) blind stitching visible 挑脚线露面35) incomplete seam stitching 线步不到尾36) uneven for hem closure stitching, uneven stitch at hem 下脚车线不直37) exposed waistband running stitches 裙头/裤头见坑线38) not straight at front fly 裤钮牌车线不顺直39) not straight at back yoke 后担干车线不直, 纽曲40) skipping stitches, looping stitches 跳线, 车线太松起耳仔41) seam allowance, sewing thread too tight 子口补间线, 线太紧起豆角42) pleated seam 骨位打褶43) puckered seam 骨位起皱44) open seam 爆骨45) burst seam 爆骨46) under seam visible 底骨露面47) waviness on seams 骨位起波浪48) twisted seams / seam rolling 扭骨49) twisting at side seam, wavy at side seam 侧骨纽, 不顺直.50) seam closures uneven 骨位结尾不平均51) missing bar-tack 漏打枣加固52) seam not properly secured 骨位不牢固53) fullness on seams 骨位太谷, 不平伏54) seam not fully opened before stitching. 骨位未完全拨开间线55) cracked seam 骨位拉时有响声(引致断线)56) too loose at princess seam 前公主骨拉松起泡57) puckering at back princess seam 后公主骨溶位太多, 起皱/起豆角58) too tight or too loose at side seam. 侧骨车线太紧或太松59) too loose at cf / cb seam 前中/后中骨太松60) too loose at shoulder seam, unbalance of front & back panel at shoulder seam 肩骨拉松(要落定位)61) too flat at shoulder seam, too slant of shoulder seam 肩骨太平/太斜shading defects 色差问题 1) color shading 色差2) color shading within one garment. 同一件衣服内有色差。3) color shading between trims and body. 配件与衫身之间有色差。4) shade differs from approved standard. 颜色与批核色版不同。5) shading caused by poor color interlining matching. 纸朴颜色不配合, 引致色差。accessories 辅料问题 1) missing button / label / badge 漏钮 / 漏唛头 / 漏章2) button position not well match buttonhole. 钮与钮门位置欠配合3) button inside out 钮的底面倒置4) button marking not removed. 点钮笔痕没有清除5) damaged button/buttonhole 钮烂/烂钮门6) rusted stud按扣 工字钮生锈7) paint peel off on stud 工字钮颜色脱落8) button and buttonhole not aligned对准的 均衡的 cause bulge. 钮及钮门位置不配合, 引致谷起9) buttonhole too small to allow button to pass through. 钮门太细, 钮不能顺利通过10) uncut buttonhole / partially cut buttonhole 钮门未幵 / 钮门未开尽11) ragged edges at buttonhole 钮门纱线不清12) broken buttonhole stitches 钮门断线13) button thread easily pulled out. 钉钮线容易拉脱14) snap / rivet easily pulled off.吸钮、撞钮容易拉脱15) buttonhole is not match button size 钮洞尺寸与钮扣大小不相配16) button misplaced 钮扣位置不对17) buttonhole misplaced 钮洞位置不对18) button is not sewing security 钮扣未钉牢19) button is sewn too tight 钮扣钉得太紧20) buttonhole is fray 钮洞有毛口21) key buttonhole density is too loose 凤眼钮洞的车缝线步太疏22) key buttonhole is misplaced 凤眼钮洞位置不对23) snap misplaced 揿钮位置不对24) snap tape is misplaced 揿钮扁带位置不对25) snap tape setting not well 揿钮扁带装得不好26) there is bubble on buttonhole area 钮洞周围有气泡27) hood and bar is misplaced 裙扣位置不对28) hole at zip top / end 拉链顶 / 尾有洞29) zipper setting is twisting 拉链装得扭曲30) shoulder pad not attach to garment security 肩棉未钉牢31) shoulder pad not cover well 肩棉未包好32) velcro is misplaced 么朮贴位置不对33) waistband belt is not set straight 腰耳装得不直 belt loop34) waistband belt length and width are uneven 腰耳的长、宽不一致35) incomplete adhesive on interlining. 黏朴未完全黏好36) strike through of adhesive on interlining. 黏朴胶露面37) strike back of adhesive on interlining. 黏朴脱落38) blistering occurred on interlining. 黏朴起泡39) insecure shoulder pad attached. 肩棉钉缝不稳40) label placement incorrect. 唛头位置不正确41) care label content not as specified. 成份唛内容不符合要求42) main label and size/content label are set too closed 主唛与尺码成份唛装得太靠近43) main label setting is misplace 钉主唛不井齐44) wrong care label sewn on garment. 成份唛车错位置45) label not properly secured. 唛头车缝不稳46) label sewn beyond label edge. 唛头车缝太入47) label sewing seam uneven / puckered. 唛头车缝不平均或48) wrong accessories used. 用错辅料button out of line. 钮位不成直线 collar 领unbalance collar 领不平衡asymmetric collar 领位不对称uneven collar width 左右领阔不一致uneven neckline 左右领圈不一致uneven collar point 领尖不对称uneven lapel shapes 左右前领咀形状不一样too much easing at c.f. neckline 前领口溶位太多(有太多溶位于前中领窝)collar too tight at cb 后领中太紧collar band is twisting 领座扭曲不平顺fullness at front collar and lapel 领及前领咀不平顺neckline is not smooth 领圈不圆顺neck setting not smooth 领子装得不平顺high & low back neck 后领圈有高低edge of front opening is crooked 前门领边不直front opening not straight 前门领边不直front facing is exposed at bottom hem 前门领贴在下摆处外露front opening facing is shorter than body 前门领贴短于大身neck was stretched 领圈拉松too much tie on front collar 前领处有豁口sleeve & armhole 袖&夹puckering at left/right armhole 左右夹圈有溶位不平伏.too loose at right armhole, uneven for left/right armhole 右夹圈有拉松, 左右夹圈不相称.sleeve running to back(衣袖走后) / sleeve running to front(衣袖走前) 操兵袖too loose at front sleeve seam 前袖骨拉松too tight at back sleeve seam 后袖骨过紧.poor cuff setting 袖子装得不好sleeve placket is not set well 袖叉装得不好underarm seam was stretched 袖底缝被拉松armhole setting not smooth 袖孔不圆顺ease on sleeve cap is uneven 袖顶缩拱不均 front/back 前后幅hiking at front, cf facing too short 吊襟hiking at back, lining too short 吊里curve at cf zip(too much fullness at cf zip) 前中拉链溶位太多curve at cf zipper because of no easing of zipper. 前中拉链无溶位(引致纽曲)hiking at back / hiking at front 后幅吊起 / 前幅吊起front panel is bigger than under panel(lining) 前幅底幅细面幅松？lining too big, too short, too small, too long 里布太大, 太短, 太小, 太长grain line are not match at front & back panel 前后幅布纹不相称front length uneven 左右前长不一致too loose at shell, too loose at back/lining, turn insider out 底松, 面松, 向外反 hem 衫脚seam binding stitch tension is too tight, causing bottom not smooth. 下摆丝带过紧, 使下摆不平顺bottom hem is not in line / not straight. 下脚不够不平(直)twisting hem, puckering at hem 下脚纽纹起豆角.un