外文翻译--传动轴简介

附 录 附录 A 外文文献原文 A shaft assembly, profile The shaft axis in two different, even in its working process and relative position between the two shafts changing. According to the important components - shaft, can have the different universal classification. If the direction in reverse universal elastic, whether can be divided into the rigid universal shaft transmission and flexible joints. The former is the hinged on parts of the power transmission link, the latter by elastic parts, and has passed dynamic buffer reduced. Rigid gimbal and can be divided into different speed universal shaft type (such as cross gimbal) and patterned (such as double type gimbal, three pin shaft type gimbal) and patterned (such as ball cage gimbal, fork type gimbal). Patterned constant, and refers to the driven shaft rotation in driving shaft with the rotation Angle, whether of equal velocity, of course, driving shaft and driven shafts is equal to the speed of the average. Lord, the driven shaft axis in two angular change when the Angle between the universal and equal still called patterned or DengJiao velocity universal. They mainly used to drive axles, breaking the wheel transmission device etc, and is mainly used in the power of the car. When the car for a rear wheel drive, often using the universal shaft, on the part of high-grade car, have adopted the isokinetic ball head, When the car for front wheel drive, often USES patterned constant - universal shaft, but also a kind of different appellation. In front of a rear wheel drive motor (or all round the bus driver), due to the automobile suspension in athletic process, main reducer drive shaft transmission (or input shaft and FenDongXiang) output shaft is relative motion between often, in addition to avoid certain institutions or device (not) line, there must be a device to realize the dynamic transfer, then the normal appeared gimbal transmission. Universal must have the following characteristics: the transmission and ensure that the relative position of the two shafts in expected range changes, can reliably transfer power, B, ensure that connects the two shafts could even operation. Due to the universal and additional load Angle, the vibration and noise should be allowed in, C, high transmission efficiency, long service life, simple structure, easy fabrication, easy maintenance. For automobile, due to a cross gimbal output shaft relative to the input shaft (have) is not constant rotation Angle, therefore, must adopt double gimbal (or more), and the universal shaft driving connected with the two cardan arrangement in the same plane and make two equal to the Angle. It is very important. In the design to minimize the Angle. Shaft assembly imbalance is the transmission of the bending vibration. The cause of the vibration noise is obvious. In addition, the universal joint cardan shaft kiln, axial clearance, the sliding spline shaft assembly precision, peeling ends when high-speed rotary shaft transmission and the elastic deformation of a hot spot balance affecting factors can change the imbalance of shaft assembly. Reducing the imbalance, shaft for cars, especially the high-speed car like (car) is extremely important, otherwise it will cause a lot of relevant fault or damage. The universal shaft rigidity of vehicle drivetrain is in the most widely used, and the long history. Usually say the shaft is generally refers to the universal shaft rigidity type. The axial rigidity of universal is mainly used in the transmission Angle of CAM flange, generally, the shaft needle bearing assembly, cardan joint or sliding fork, fork or spline fork, needle bearing axial fixation. Ashdod, with the gearbox commonly margin fork shaft drive or other such links. Tu margin with a fork is the flange, generally USES the fork form part of the carbon steel or medium-carbon steel forging, also have adopted the ductile iron castings and sand carbon steel or medium-carbon steel high precision castings. Tu margin with a flat binary general, also have brought a flanged end flange of trapezoid tooth. The shaft needle bearing assembly includes four needle bearing, a cross axis, a grease. Roller bearings are generally consists of several needle roller bearings, a bowl, a blade rubber seal (more than with partial skeleton). In some needle bearing, and a belt round bearings, nylon, gasket also adopts copper or other materials, mainly for the decrease of universal shaft axial clearance, improve the quality of dynamic balance. A binary form cardan parts, generally USES medium-carbon steel or carbon steel forging parts, also have adopted the precision casting medium-carbon steel. Needle bearing axial fixation thing is generally holes (or axis) with elastic ring (internal and external), or bearing the cassette, bolt locking plate, etc.Another shaft is an important part of the spline is sliding, internal and external spline (rectangular), and the involute used to convey length change.The universal shaft and sliding swinging Angle of slip is biggest spline is decorated, according to the vehicle shaft and beat the check.Transmission of low carbon steel tube generally made of steel wire coiling of big norms, the tube, also have adopted the cold drawn seamless tube. The tube diameter and wall thickness (or diameter) is based on the maximum transmission torque, highest speed conditions of work. Hollow shaft tube has smaller quality and can deliver large torque, and the same diameter than the solid shaft possesses higher critical speed characteristics. Normally, two gimbal centre distance is not more than 1.5 m. When the distance is close, generally by two universal and a sliding spline shaft, no vice. When the distance and make more than 1.5 m shaft length, often divided into two or three roots, using three or four joints, and finally a belt, the rest of the spline vice sliding bearing structure among belt.Typical middle by a supporting general cylindrical ball bearing, a housing, two seal, a rubber pad, a grease mouth. By supporting bracket among middle shaft connecting to the frame beams, transmission line and the middle axis required support among perpendicular to the plane. General layout in supporting shaft transmission system among the first-order critical speed nodes.In use process, generally need timely maintenance. In the joints, sliding bearing etc, among the spline is fat mouth place, want to periodically according to related regulations prescribed grease filling. Also have adopted in maintenance free universal shaft bearings and support in the reserve, need not regular grease filling grease. Second, the universal description Universal joint is a key component of the car transmission. In front of the rear wheel drive motor vehicle, universal shaft installed in transmission and the output shaft drive between input shaft gear reducer, And lead the front wheel drive motor vehicle omitted, universal shaft driving is responsible for installation in the front axle and be responsible for steering wheels and half shaft. Automobile is a movement of objects. The bus driver, engine, clutch and transmission as a whole, and installed in the frame by elastic suspension frame and drive connections between a distance, the need for connection. The car runs in rough pavement produces change, load or two assembly location, will make the output shaft transmission with the reducer drive shaft Angle between input and the distance change, therefore, to use a in changing devices to solve this question, it is the universal. In between, off-road vehicle transmission and the front drive thansfer can turn with half shaft drive between the universal, need to do . The structure and function of a bit like human limbs, it is allowed to connect the Angle between the parts. But it and body joints and different forms of activities, it only allows the Angle of the change in a certain range.Universal shaft type is the universal, rigid patterned (double axle and three pin shaft type), patterned (ball fork and ball cage), cross gimbal sex. After the car at the most widely used a cross gimbal.Single gimbal cannot make the output shaft and the instantaneous velocity of axle shaft vibration, easy to cause the equal parts, aggravate the damage, produce a lot of noise. Therefore, after the car driver using universal form of transmission shaft double gimbal, is a universal at each end, its function is equal to the transmission Angle, both the output shaft and the instantaneous velocity of axle shaft always equal. In order to satisfy the power transmission, steering and auto operation generated by beating down before the Angle, drive the car drive shaft and the wheel, and also used between universal connected. Due to the limit, the axial dimensions of landform and bigger, request to do, so common universal widely adopted various patterned. In general, the former drive car every half shaft with two patterned, near the speed of universal joint is a half drive axle shaft inside, near the universal shaft lateral velocity is half. In various patterned, common ball cage is universal, it with six steel ball force, driving shaft and driven shafts intersect in any of the circumstances, the ball is located on the intersection of two in two axis, namely the equally intersect, thus ensure the driven shaft, equal angles speed transmission. 附录 B 外文文献中文翻译 传动轴简介 传动轴，在不同轴心的两轴间甚至在工作过程中相对位置不断变化的两轴间传递动力。传动轴按其重要部件 万向节的不同，可有不同的分类。如果按万向节 在扭转的方向是否有明显的弹性可分为刚性万向节传动轴和挠性万向节传动轴。前者是靠零件的铰链式联接传递动力的，后者则靠弹性零件传递动力，并具有缓冲减振作用。刚性万向节又可分为不等速万向节（如十字轴式万向节）、准等速万向节（如双联式万向节、三销轴式万向节）和等速万向节（如球笼式万向节、球叉式万向节）。等速与不等速，是指从动轴在随着主动轴转动时，两者的转动角速率是否相等而言的，当然，主动轴和从动轴的平均转速是相等的。 主、从动轴的角速度在两轴之间的夹角变动时仍然相等的万向节，称为等速万向节或等角速万向节。 它们主要用于转向驱动桥、断开式驱动桥等的车轮传动装置中，主要用于轿车中的动力传递。当轿车为后轮驱动时，常采用十字轴式万向节传动轴，对部分高档轿车，也有采用等速球头的；当轿车为前轮驱动时，则常采用等速万向节 等速万向节也是一种传动轴，只是称谓不同而已。 在 发动机 前置后轮驱动（或全轮驱动）的汽车上，由于汽车在运动过程中悬架变形，驱动轴主减速器输入轴与变速器（或分动箱）输出轴间经常有相对运动，此外，为有效避开某些机构或装置（无法实现直线传递），必须有一种装置来实现动力的正常传递，于是就出现了万向节传动 。万向节传动必须具备以下特点：a、 保证所连接两轴的相对位置在预计范围内变动时，能可靠地传递动力； b 、保证所连接两轴能均匀运转。由于万向节夹角而产生的附加载荷、振动和噪声应在允许范围内； c 、 传动效率要高，使用寿命长，结构简单，制造方便，维修容易。对汽车而言，由于一个十字轴万向节的输出轴相对于输入轴（有一定的夹角）是不等速旋转的，为此必须采用双万向节（或多万向节）传动，并把同传动轴相连的两个万向节叉布置在同一平面，且使两万向节的夹角相等。这一点是十分重要的。在设计时应尽量减小万向节的夹角。 传动轴 总成不平衡是传动系弯曲振动的主要原因。其引起的振动噪声是明显的。此外，万向节十字轴的轴向窜动、传动轴滑动花键中的间隙、传动轴总成两端连接处的定心精度、高速回转时传动轴的弹性变形及传动轴上点焊平衡片时的热影响因素等都能改变传动轴总成的不平衡度。降低传动轴的不平衡度，对于汽车，尤其是高速汽车如（轿车）是极其重要的，否则会引起很多相关故障或异常损坏。 十字轴式刚性万向节传动轴在汽车传动系中用得最广泛，历史也最悠久。平时所说的传动轴一般指的就是十字轴式刚性万向节传动轴。十字轴式刚性万向节主要用于传递角度的 变化，一般由突缘叉、十字轴带滚针轴承总成、万向节叉或滑动叉、中间连接叉或花键轴叉、滚针轴承的轴向固定件等组成。突缘叉一般与变速箱 、驱动桥或别的传动轴等连接。突缘叉是一个带法兰的叉形零件，一般采用中碳钢或中碳合金钢的锻造件，也有采用球墨铸铁的砂型铸造件和中碳钢或中碳优质合金钢的精密铸造件。突缘叉一般带一个平法兰，也有带一个端面梯形齿法兰的。十字轴带滚针轴承总成一般包括四个滚针轴承、一个十字轴、一个滑脂嘴。滚针轴承一般由若干个滚针、一个轴承碗、一个多刃口橡胶油封（部分带骨架）组成。在某些滚针轴承中，还有一个带油 槽的圆形垫片，有尼龙的，也有采用铜片或其他材料的，主要用于减小万向节轴向间隙，提高传动轴动平衡品质。万向节叉是一个叉形零件，一般采用中碳钢或中碳合金钢的锻造件，也有采用中碳钢的精密铸造件。滚针轴承的轴向固定件一般是孔（或轴）用弹性挡圈（内外卡式），或轴承压板、锁片、螺栓等。 传动轴的另外一个重要的组成部分是滑动花键副，由内、外花键（矩形、渐开线）组成，用于传递长度的变化。传动轴的万向节摆角和滑动花键副的最大伸缩量，是根据整车布置时进行的传动轴跳动校核而确定的。传动轴管一般由低碳钢板卷制的电焊钢管制 成，对大规格的轴管，也有采用冷拔无缝管的。轴管的外径和壁厚（或内径）是根据传动轴所传递的最大工作扭矩、最高工作转速等条件确定的。空心的轴管具有较小的质量并能传递较大的扭矩，并且比相同