模具零部件名称及中英文对照.doc

作业指导书文件名称文件编号：WI-EN-001制定日期：2006-08-23模具零部件名称及中英文对照文件版次：A/01发行日期：2006-08-24修订：1次页次：第 13 页 共 13 页版本修订内容修订日期修订者NO.12345678910部门单位总经理管理代表行政部业务部工程部品管部资材部生产部分发份数分发号文件受控章批准审核制定1.0目的： 统一公司模具及配件的名称，以方便进行标识与追溯。2.0范围： 适用于福帆公司模具及配件统一名称。3.0权责：3.1工程部：统一公司的模具及配件的名称。3.2相关部门：按工程部的统一名称进行相关标识与作业。4.0内容： 41模具零部件名称：SideSideNippleSideInsKnockEjector BladeInsAngel lifterSprue bushinggate insert heel blockAnlgeHeal blockGIBSlideSafety strapSleeve pinLatch lock42模具零部件中英文对照：Mould base 模架Moving half 动模Top clamping plate (TCP)上模板Fixing half定模A plateA板Cavity 上模型腔B plateB板Cavity pin (cav Pin)上模镶针Spacer block方铁Cavity insert (Cav Ins)上模镶件Ejector retain plate (Eje Retain Pla)顶针面板Core下模型芯Ejector plate (Eje Pla)顶针底板Core pin下模镶针Bottom clamping plate (BCP)下模板Core insert (Core Ins)下模镶件Runner stripper plate流道板Floating core浮呵Support plate支撑板Safety strap 安全锁扣Manifold retainer plate热流道板Puller plate 定位拉板Stripper plate (str pla) 推板Straight side interlock精定位Insulate plate隔热板Slide滑块Eyebolt吊环Slide wear plate (sld w p)滑块底部耐磨板Leader bushing (Lea Bus)导套heel block 铲机Leader pin导柱Slide center guide滑块中心导轨Shoulder guide bush有托导套Slide insert (sld ins)滑块型芯Ejector guide bushings中托司Slide pin (sld Pin)滑块镶针Straight guide bush直导柱Slide stopper plate (sld stop pla)滑块限位板Ball Ejector bush滚珠导套Gib滑块压板Self-lubricating自润滑Spacer ring垫圈Return pin 回针Locating ring 定位圈Tapered interlock圆形锥度精定位Ejector bar (eje bar) 顶块Rectangular interlock 方形精定位Knock rod顶棍Ejector sleeve (Eje Sle)丝筒Knockout hole顶棍孔Sleeve pin丝筒针Support pillar (S.P) 支撑柱Ejector blade扁顶针Edge gate侧胶口Ejector pin (Eje Pin)顶针Pinpoint gate 细水口Stepped ejector Pin有托顶针Submarine潜水口Sleeve pin block (sle pin blk)丝筒压紧块Gate入水口Gate insert点浇口镶件Angle lifter (AL)斜顶Distance spacer顶距限位杆Lifter guide (Lif Guide)斜顶导向块Puller pin拉杆Lifter slide (Lif Sl)斜顶滑块Puller bolt collar拉杆介指Lifter wear plate (Lif W P)斜顶耐磨块Helical spindle来福线丝杆Latch lock扣机Helical nut来福线丝套Interchangeable Insert替换镶件Dowel pin销钉Fix block固定块Distance bolt (dis bolt)拉杆限位钉Wedge block (wedge blk)逼紧块Sprue puller pin 拉料针Connector block连接块Angle pin斜导柱Angle pin insert斜导柱镶件S.H.C.S内六角螺丝Lifter block平衡杆H.S.S无头螺丝Adjust plate调节板F.H.S平头螺丝Stripper insert (str ins)推板镶件Socket set screw无头螺丝Baffle隔水片Sholder screw (SH scw)塞打螺丝Connector sockets快速接头Spring loaded set screw波仔螺丝Oil nipple 油管接头Limit switch限位开关Pressure plug(1/4 1/8NPT)堵头Hydraulic motor油压马达Plug (1/4 1/8NPT) 水嘴Oil cylinder油缸Extension plug加长水嘴Air cylinder汽缸Cooling block运水块Tapered interlocks锥度锁Quick clamp pin快速码模杆Slide retainer行位锁Angle nipples转弯接头Counter计数器Wire connector接线盒Air poppet valve气阀MB-stand模具撑脚Mold dating inserts日期章Treadless brass pressure pliugs 止水栓Spring弹簧Nitriding渗氮Stopper pin (st pin)垃圾钉Tempering回火O ring O型圈Annealing退火Parallel key平键Hardening淬火Bearing轴承Parting line分模线Rack齿条Datum基准Gear wheel齿轮Detail详图Threaded bush螺纹衬套Draft出模角Two stage ejector二次顶出装置Finish光洁度Early ejector return assembly先复位机构Kiss off碰穿Runner流道Venting疏气Hot runner热流道Revision (REV.)修正Heated nozzle热喷嘴Undercut(u cut)倒扣Thermocouple热电偶Engrave雕字Cartridge heated加热棒Raised凸高Sprue bushing (sprue bus)浇口套Flush平凹Heat pipes散热针Shut off擦位Vent pin散气针Tolerance (TOL.)公差Puller insert (puller ins)勾针镶件Texture皮纹Extension bushing加长唧嘴套Logo商唛Ejector set cov