IEC61850工程实施规范 附录A 逻辑节点类一致性要求 (企业报批稿).doc

IEC61850工程实施规范附录A：逻辑节点类一致性要求A.1逻辑节点零LLN0属性名属性类型全称M/O中文语义公用逻辑节点信息ModINCModeM模式BehINSBehaviourM行为HealthINSHealthM健康状态NamPltLPLNameM逻辑节点铭牌LocSPSLocal operation for complete logical deviceO就地位置OpTmhINSOperation timeO运行时间控制DiagSPCRun DiagnosticsO装置自检LEDRsSPCLED resetO复归LEDMainEnaSPCE主保护软压板MainEna2SPCE主保护2软压板DISEnaSPCE距离保护软压板RTOCEnaSPCE零序过流软压板RETRIPEnaSPCE远跳投入软压板CHARGEnaSPCE充电保护软压板ROCEnaSPCE相电流保护软压板AccelEnaSPCE双回线加速软压板A.2 保护通道PSCH属性名属性类型全称M/O中文语义公用逻辑节点信息ModINCModeM模式BehINSBehaviourM行为HealthINSHealthM健康状态NamPltLPLNameM逻辑节点铭牌OpCntRsINCResetable operation counterO可复归的动作计数器状态信息ProTxSPSTeleprotection signal transmittedM纵联保护发信或远跳保护发信ProRxSPSTeleprotection signal receivedM纵联保护收信或远跳保护收信StrACDCarrier SendM启动OpACTOperateM动作 纵联保护动作或远跳保护动作CarRxACTCarrier received after unblock logicO解闭锁逻辑收信LosOfGrdSPSLoss of guardO监频消失EchoACTEcho signal from weak end infeed functionO弱馈回音信号WeiOpACTOperate signal from weak end infeed functionO弱馈动作信号RvABlkACTBlock signal from current reversal functionO功率倒向闭锁信号GrdRxSPSGuard ReceivedO监频收信RemSig1TxSPSRemote signal 1 receivedE远传1发信RemSig1RxSPSE远传1收信RemSig2TxSPSRemote signal 2 receivedE远传2发信RemSig2RxSPSE远传2收信PhSegPmsEnaACTPhase Segregated Permiss ive Signal EnableE分相允许信号Ch1AlmSPSChannel 1 alarmE通道1告警Ch2AlmSPSChannel 2 alarmE通道2告警ChFailSPSChannel failedE通道中断SynErrSPSSynchronization errorE同步出错ChSwSPSChannel switchedE通道切换ChNeedChkSPSChannel need checkE通道需检查ChDlLongSPSChannel transmission delay too longE通道传输延时过长ChDlUnstdSPSChannel transmission delay unsteadyE通道传输延时不稳定Ch1IDUnmachSPSChannel 1 ID unmatchedE通道1编号不匹配Ch2IDUnmachSPSChannel 2 ID unmatchedE通道2编号不匹配RemTrPersSPSRemote trip persistentE远跳长期不复归RemSig1PersSPSRemote signal 1 persistentE远传1长期有开入RemSig2PersSPSRemote signal 2 persistentE远传2长期有开入A.3 保护跳闸逻辑PTRC属性名属性类型全称M/O中文语义公用逻辑节点信息ModINCModeM模式BehINSBehaviourM行为HealthINSHealthM健康状态NamPltLPLNameM逻辑节点铭牌OpCntRsINCResetable operation counterO可复归的动作计数器控制TrLPSPCE跳闸出口压板StrBFLPSPCE启动失灵出口压板StrRecLPSPCE启动重合闸出口压板BlkRecLPSPCE闭锁重合闸出口压板StrRemTrLPSPCE启动远跳出口压板StrBusTrLPSPCE失灵启动母差出口压板状态信息TrACTTripC跳闸OpACTOperateC动作StrACDStartO启动StrBFACTStart Braker FailureE启动失灵StrRecACTStart RecloserE启动重合闸BlkRecSPSBlock RecloserE闭锁重合闸StrRemTrSPSStart Remote TripE启动远跳StrBusTrSPSStart Bus TripE失灵启动母差跳闸PSelFailTPSPStriple pole tripping for phase select failedE选相无效三跳SPlFailTPSPStriple pole tripping for single pole tripping failedE单跳失败三跳TPFailPTSPSPersistent tripping for triple pole tripping failedE三跳失败永跳PerTriFailSPSPersistent tripping failE永跳失败SPhRunTPSPStriple pole tripping for single phase runningE单相运行三跳条件C: Tr，Op状态信息中至少应该使用一个。A.4 三相不一致保护PPDP（Pole Disagreement Protection）属性名属性类型全称M/O中文语义公用逻辑节点信息ModINCModeM模式BehINSBehaviourM行为HealthINSHealthM健康状态NamPltLPLNameM逻辑节点铭牌OpCntRsINCResetable operation counterO可复归的动作计数器状态信息StrACDStartM启动OpACTOperateM动作A.5 自动重合闸RREC属性名属性类型全称M/O中文语义公用逻辑节点信息ModINCModeM模式BehINSBehaviourM行为HealthINSHealthM健康状态NamPltLPLNameM逻辑节点铭牌OpCntRsINCResetable operation counterO可复归的动作计数器控制BlkRecSPCBlock ReclosingO重合闸软压板ChkRecSPCCheck ReclosingO检同期投入压板FstRecEnSPCEnable the master auto-reclosingE投先合软压板（3/2接线边开关先合闸）RecMod1SPCE重合闸方式1软压板RecMod2SPCE重合闸方式2软压板OpLPSPCE重合闸出口压板TPTrEnaLPSPCE沟通三跳出口压板状态信息AutoSPSAutomatic Operation (external switch status)O开关自动状态OpACTOperate (used here to provide close to XCBR)M动作. 重合闸动作信号AutoRecStINSAuto Reclosing StatusM重合闸状态TPTrEnaSPSThree pole tripping enableE沟通三跳OpTrgRecStSPSE保护跳闸起动重合TPTrgRecStSPSE保护三跳起动重合A.6 冷却器全停监视SCAS（Cooler All Stopped）属性名属性类型全称M/O中文语义公用逻辑节点信息ModINCModeM模式BehINSBehaviourM行为HealthINSHealthM健康状态NamPltL