关 键 词：

5张CAD图纸及文档全套打包 数控加工中心 盘式刀库 设计 20 CAD 图纸 文档 全套 打包

资源描述：

购买设计请充值后下载，，资源目录下的文件所见即所得，都可以点开预览，，资料完整，充值下载就能得到。。。【注】：dwg后缀为CAD图，doc,docx为WORD文档，有不明白之处，可咨询Q:414951605

内容简介：

摘 要随着数控技术的发展和普及，加工中心的作用越发突显它的重要性。为进一步提高数控机床的加工效率，数控机床正向着工件在一台机床一次装夹即可完成多道工序或全部工序加工的方向发展，因此出现了各种类型的加工中心机床，如车削中心、镗铣加工中心、钻削中心等等。这类多工序加工的数控机床在加工过程中要使用多种刀具，因此必须有自动换刀装置，也就是所说的刀库，以便选用不同刀具，完成不同工序的加工工艺。自动换刀装置应当具备换刀时间短、刀具重复定位精度高、足够的刀具储备量、占地面积小、安全可靠等特性。本论文是开发设计出一种体积小、结构紧凑、价格较低、生产周期短的小型立式加工中心无机械手换刀刀库。首先介绍了国内外加工中心研究现状及发展趋势，阐明了本课题研究的目的、意义。然后进一步介绍本小型加工中心刀库总体结构和各部件方案的选择，并在此基础上进行了小型加工中心刀库的机械结构的设计计算，主要包括刀盘部件设计（含刀盘，夹块，刀爪），刀库转动定位机构设计（含转臂，槽轮，滚子，锁止盘），刀库总体机构设计（含轴承套，轴，箱盖，箱体）刀库移动部分设计。关键词：数控系统 加工中心 刀库AbstractAlong with the numerical control technology development and the popularization, the processing center function reveals its importance even more suddenly. For further enhances the numerical control engine laths the processing efficiency, the numerical control engine laths is clamping to the work piece in an engine laths attire then completes the multi-channel working procedure or the complete working procedure processing direction develops, therefore appeared each kind of type processing center engine laths, ike the turning center, the boring mill processing center, drills truncates center and so on. This kind of working procedure processing numerical control engine laths must use many kinds of cutting tools in the processing process, therefore must have trades the knife installment automatically, also is the knife storehouse which said, in order to select the different cutting tool, completes the different working procedure the processing craft. Trades the knife equipment to have automatically to have trades the knife time short, the cutting tool repetition pointing accuracy high, the enough cutting tool margin, the area small, safe reliable and so on the characteristics. The present paper is the development designs one kind of volume slightly, the structure compact, the price is low, production cycle short small vertical processing center knife storehouse this article. Then further introduced this small processing center knife storehouse overall structure and various parts plan choice, and has carried on the small processing center knife storehouse mechanism design calculation in this foundation, mainly includes the knife storehouse overall organization design, the electrical machinery selection, the knife storehouse rotation detent mechanism design knife storehouse migration part design and so on. Keywords: numerically controlled lathe machining centers cut database目 录摘要iAbstractii1 绪论1 1.1 国内外的研究现状和发展趋势1 1.1.1 当前世界NC机床的研究现状1 1.1.2 我国数控机床产业的发展状况2 1.1.3 加工中心的发展动向3 1.1.4 我国数控机床研究存在的问题3 1.2 加工中心概论4 1.2.1 自动换刀系统产品化的意义和前景6 1.3 本论文研究的目的和意义6 1.4 本论文完成的主要工作6 2 总体方案的设计8 2.1 运动方案的设计8 2.1.1 运动数目的确定8 2.1.2 运动方案的确定8 2.2 功能部件的设计方案9 2.2.1 主传动系统9 2.2.2 进给伺服系统10 2.2.3自动换刀系统11 2.2.4 基础部件13 2.2.5 数控系统14 2.2.6 辅助装置142.3 总体布局142.4 主要技术参数14 2.5 小结16 3 刀库的设计17 3.1 刀库的结构设计17 3.1.1 刀库主要参数的确定17 3.1.2 刀盘部分的设计17 3.1.3 刀库转动定位机构的设计18 3.1.4 轴的设计21 3.1.5 滚动轴承的选择计算24 3.1.6 键的选用与计算25 3.1.7 刀库的支承部分的设计25 3.2 刀库移动部分的设计26 3.2.1 刀库支承横梁和导轨的设计26 3.2.2 刀库移动丝杠和电机的选择27 3.3 刀库、横梁的安装27 3.4 小结38 结论29 致谢30 参考文献31 ivNUMERICAL CONTROLNumerical control(NC)is a form of programmable automation in which the processing equipment is controlled by means of numbers，letters，and other symbolsThe numbers，letters，and symbols are coded in an appropriate format to define a program of instructions for a particular workpart or jobWhen the job changes，the program of instructions is changedThe capability to change the program is what makes NC suitable for low-and medium-volume productionIt is much easier to write programs than to make major alterations of the processing equipmentThere are two basic types of numerically controlled machine tools：pointtopoint and continuouspath(also called contouring)Pointtopoint machines use unsynchronized motors，with the result that the position of the machining head Can be assured only upon completion of a movement，or while only one motor is runningMachines of this type are principally used for straightline cuts or for drilling or boring The NC system consists of the following components：data input，the tape reader with the control unit，feedback devices，and the metalcutting machine tool or other type of NC equipmentData input，also called“mantocontrol link”，may be provided to the machine tool manually，or entirely by automatic meansManual methods when used as the sole source of input data are restricted to a relatively small number of inputsExamples of manually operated devices are keyboard dials，pushbuttons，switches，or thumbwheel selectorsThese are located on a console near the machineDials ale analog devices usually connected to a syn-chro-type resolver or potentiometerIn most cases，pushbuttons，switches，and other similar types of selectors aye digital input devicesManual input requires that the operator set the controls for each operationIt is a slow and tedious process and is seldom justified except in elementary machining applications or in special casesIn practically all cases，information is automatically supplied to the control unit and the machine tool by cards，punched tapes，or by magnetic tapeEightchannel punched paper tape is the most commonly used form of data input for conventional NC systemsThe coded instructions on the tape consist of sections of punched holes called blocksEach block represents a machine function，a machining operation，or a combination of the twoThe entire NC program on a tape is made up of an accumulation of these successive data blocksPrograms resulting in long tapes all wound on reels like motion-picture filmPrograms on relatively short tapes may be continuously repeated by joining the two ends of the tape to form a loopOnce installed，the tape is used again and again without further handlingIn this case，the operator simply loads and unloads the partsPunched tapes ale prepared on type writers with special tapepunching attachments or in tape punching units connected directly to a computer systemTape production is rarely error-freeErrors may be initially caused by the part programmer，in card punching or compilation，or as a result of physical damage to the tape during handling，etcSeveral trial runs are often necessary to remove all errors and produce an acceptable working tape While the data on the tape is fed automatically，the actual programming steps ale done manuallyBefore the coded tape may be prepared，the programmer，often working with a planner or a process engineer, must select the appropriate NC machine tool，determine the kind of material to be machined，calculate the speeds and feeds，and decide upon the type of tooling needed. The dimensions on the part print are closely examined to determine a suitable zero reference point from which to start the programA program manuscript is then written which gives coded numerical instructions describing the sequence of operations that the machine tool is required to follow to cut the part to the drawing specificationsThe control unit receives and stores all coded data until a complete block of information has been accumulatedIt then interprets the coded instruction and directs the machine tool through the required motionsThe function of the control unit may be better understood by comparing it to the action of a dial telephone，where，as each digit is dialed，it is storedWhen the entire number has been dialed，the equipment becomes activated and the call is completedSilicon photo diodes，located in the tape reader head on the control unit，detect light as it passes through the holes in the moving tapeThe light beams are converted to electrical energy，which is amplified to further strengthen the signalThe signals are then sent to registers in the control unit, where actuation signals are relayed to the machine tool drivesSome photoelectric devices are capable of reading at rates up to 1000 characters per secondHigh reading rates are necessary to maintain continuous machinetool motion；otherwise dwell marks may be generated by the cutter on the part during contouring operationsThe reading device must be capable of reading data blocks at a rate faster than the control system can process the dataA feedback device is a safeguard used on some NC installations to constantly compensate for errors between the commanded position and the actual location of the moving slides of the machine toolAn NC machine equipped with this kind of a direct feedback checking device has what is known as a closed-loop systemPositioning control is accomplished by a sensor which，during the actual operation，records the position of the slides and relays this information back to the control unitSignals thus received ale compared to input signals on the tape，and any discrepancy between them is automatically rectifiedIn an alternative system，called an openloop system，the machine is positioned solely by stepping motor drives in response to commands by a controllersThere are three basic types of NC motions, as follows: Point-to-point or Positional Control In point-to-point control the machine tool elements (tools, table, etc.) are moved to programmed locations and the machining operations performed after the motions are completed. The path or speed of movement between locations is unimportant; only the coordinates of the end points of the motions are accurately controlled. This type of control is suitable for drill presses and some boring machines, where drilling, tapping, or boring operations must be performed at various locations on the work piece. Straight-Line or Linear Control Straight-Line control systems are able to move the cutting tool parallel to one of the major axes of the machine tool at a controlled rate suitable for machining. It is normally only possible to move in one direction at a time, so angular cuts on the work piece are not possible, consequently, for milling machines, only rectangular configurations can be machined or for lathes only surfaces parallel or perpendicular to the spindle axis can be machined. This type of controlled motion is often referred to as linear control or a half-axis of control. Machines with this form of control are also capable of point-to-point control.Continuous Path or Contouring Control In continuous path control the motions of two or more of the machine axes are controlled simultaneously, so that the position and velocity of the can be tool are changed continuously. In this way curves and surfaces can be machined at a controlled feed rate. It is the function of the interpolator in the controller to determine the increments of the individual controlled axes of the machines necessary to produce the desired motion. This type of control is referred to as continuous control or a full axis of control.Some terminology concerning controlled motions for NC machines has been introduced. For example, some machines are referred to as four-or five-or even six-axis machines. For a vertical milling machine three axes of control are fairly obvious, these being the usual X, Y, Z coordinate directions. A fourth or fifth axis of control would imply some form of rotary table to index the work piece or possibly to provide angular motion of the work head. Thus, in NC terminology an axis of control is any controlled motion of the machine elements (spindles, tables, etc). A further complication is use of the term half-axis of control; for example, many milling machines are referred to as 2.5-axis machine. This means that continuous control is possible for two motions (axes) and only linear control is possible for the third axis. Applied to vertical milling machines, 2.5axis control means contouring in the X, Y plane and linear motion only in the Z direction. With these machines three-dimensional objects have to be machined with water lines around the surface at different heights. With an alternative terminology the same machine could be called a 2CL machine (C for continuous, L for linear control). Thus, a milling machine with continuous control in the X, Y, Z directions could be termed be a three-axis machine or a 3c machine, Similarly, lathes are usually two axis or 2C machines. The degree of work precision depends almost entirely upon the accuracy of the lead screw and the rigidity of the machine structureWith this systemthere is no self-correcting action or feedback of information to the control unitIn the event of an unexpected malfunction，the control unit continues to put out pulses of electrical currentIf，for example，the table on a NC milling machine were suddenly to become overloaded，no response would be sent back to the controllerBecause stepping motors are not sensitive to load variations，many NC systems are designed to permit the motors to stall when the resisting torque exceeds the motor torqueOther systems are in use，however，which in spite of the possibility of damage to the machine structure or to the mechanical system，ale designed with special hightorque stepping motorsIn this case，the motors have sufficient capacity to“overpowerthe system in the event of almost any contingency The original NC used the closedloop systemOf the two systems，closed and open loop，closed loop is more accurate and，as a consequence，is generally more expensiveInitially，openloop systems were used almost entirely for light-duty applications because of inherent power limitations previously associated with conventional electric stepping motorsRecent advances in the development of electro hydraulic stepping motors have led to increasingly heavier machine load applications.数控技术数控是可编程自动化技术的一种形式，通过数字、字母和其他符号来控制加工设备。数字、字母和符号用适当的格式编码为一个特定工件定义指令程序。当工件改变时，指令程序就改变。这种改变程序的能力使数控适合于中、小批量生产，写一段新程序远比对加工设备做大的改动容易得多。数控机床有两种基本形式：点位控制和连续控制(也称为轮廓控制)。点位控制机床采用异步电动机，因此，主轴的定位只能通过完成一个运动或一个电动机的转动来实现。这种机床主要用于直线切削或钻孔、镗孔等场合。数控系统由下列组件组成：数据输入装置，带控制单元的磁带阅读机，反馈装置和切削机床或其他形式的数控设备。数据输人装置，也称“人机联系装置”，可用人工或全自动方法向机床提供数据。人工方法作为输人数据唯一方法时，只限于少量输入。人工输入装置有键盘，拨号盘，按钮，开关或拨轮选择开关，这些都位于机床附近的一个控制台上。拨号盘通常连到一个同步解析器或电位计的模拟装置上。在大多数情况下，按钮、开关和其他类似的旋钮是数据输入元件。人工输入需要操作者控制每个操作，这是一个既慢又单调的过程，除了简单加工场合或特殊情况，已很少使用。几乎所有情况下，信息都是通过卡片、穿孔纸带或磁带自动提供给控制单元。在传统的数控系统中，八信道穿孔纸带是最常用的数据输入形式，纸带上的编码指令由一系列称为程序块的穿孔组成。每一个程序块代表一种加工功能、一种操作或