摘要.doc

机械毕业设计-400×1500片材离心成型机设计(含CAD图纸全套)

收藏

压缩包内文档预览:
预览图 预览图 预览图 预览图 预览图 预览图 预览图 预览图 预览图
编号:50653721    类型:共享资源    大小:1.98MB    格式:RAR    上传时间:2020-02-22 上传人:机****料 IP属地:河南
50
积分
关 键 词:
机械 毕业设计 400 1500 离心 成型 设计 CAD 图纸 全套
资源描述:
机械毕业设计-400×1500片材离心成型机设计(含CAD图纸全套),机械,毕业设计,400,1500,离心,成型,设计,CAD,图纸,全套
内容简介:
沈阳化工大学科亚学院学士学位论文 引言摘要聚氨酯全称为聚氨基甲酸酯 ,是主链上含有重复氨基甲酸酯基团的大分子化合物的统称。它是由有机二异氰酸酯或多异氰酸酯与二羟基或多羟基化合物加聚而成。聚氨酯大分子中除了氨基甲酸酯外 ,还可含有醚、酯、脲、缩二脲 ,脲基甲酸酯等基团。聚氨酯成型机是通过对聚氨酯加热到熔融状态,再靠离心机的离心原理将熔融的聚氨酯输送到搅拌头。经过高速强烈搅拌,使之料液均匀而喷出,形成所需产品。而离心成型技术是利用离心力成型管状或空心筒状制品的方法。通过挤出机或专用漏斗将定量的液态树脂或树脂分散体注入旋转并加热的容器(即模具)中,使其绕单轴高速旋转(每分钟几十转到两千转),此时放入的物料即被离心力迫使分布在模具的近壁部位。在旋转的同时,放入的物料发生固化,随后视需要经过冷却或后处理即能取得制品。在成型增强塑料制品时还可同时加入增强性的填料。离心浇铸通常用的都是熔体粘度较小、热稳定性较好的热塑性塑料,如聚酰胺、聚乙烯、聚氨酯等。离心成型时,聚氨酯填充模具型腔主要靠的是离心机旋转时产生的离心力。离心力与质量成正比,与离心机转速的平方成正比,与旋转半径成正比。因此,对某一规格的转子而言,聚氨酯的质量和旋转半径是一定的,所以离心力的大小仅与离心机的转速有关,增大或减少离心力,只须改变离心机的转速即可。在离心成型时,聚氨酯除了受到自身的重力作用外,主要是靠离心力的作用来填充模具型腔的,其填充方式是先填充远离旋转中心的型腔的外部,然后逐渐向心部填充完毕。因有离心力的存在,且它比重力大得多,所以聚氨酯的填充能力要比重力成型时强,只要离心机转速适当,离心力的大小合适,生产出的转子的质量就一定比浇注成型时形成的转子要好得多。关键词:聚氨酯;离心成型;滚筒AbstractPolyurethane full-called polyurethane, is the main chain contains repeating urethane groups of molecules, collectively. It is an organic diisocyanate or polyisocyanate or polyol with two hydroxyl addition polymerization is made. Polyurethane macromolecules in addition to urethane, it can also contain ether, ester, urea, biuret, urea-based groups such as ester.Polyurethane polyurethane molding machine is heated to melt through the state to rely on the principle of centrifuge centrifuge transported to the melting of the polyurethane mixing head. After strong stirring speed, so that even the spray liquid, to form the desired product. The centrifugal molding technology is the use of centrifugal force forming tubular or hollow tubular products method.Through the extruder hopper or dedicated to quantitative liquid resin or resin dispersion into the rotation and heating container (ie, mold), making it rotate around the axis high-speed (tens of per minute to two thousand rpm), then put incurs centrifugal force into the material distributed in the mold wall parts. Rotating at the same time, into the material cures, and then as needed through the cooling or post-processing that is able to obtain products. Enhanced the molding plastic products can also added to enhance the nature of filler. Centrifugal casting melt viscosity are usually smaller, better thermal stability of thermoplastics such as polyamide, polyethylene, polyurethane, etc.Centrifugal molding, polyurethane fill the mold cavity is the main centrifuge rotation by the centrifugal force generated. Centrifugal force is proportional with the quality, speed proportional to the square with the centrifuge, and the radius is proportional to. Therefore, a specification of the rotor, the polyurethane is a certain quality and radius, so the size of the centrifugal force only with the speed of the centrifuge, increase or reduce the centrifugal force, centrifuge speed can only change.In centrifugal molding, polyurethane except by their own gravity, the centrifugal force depends mainly on the role to fill the mold cavity, the fill mode is first filling away from the center of rotation of the external cavity, and then gradually to the heart of the Department of Tianchong completed . Due to the presence of centrifugal force, gravity force and it is much larger, so the polyurethane molding filling capacity than gravity is strong, as long as the appropriate centrifuge speed, the centrifugal force of the right size to produce the quality of the rotor must be better than pouring molding form The rotor is much better.Key words: polyurethane; centrifugal molding; drum 目 录引言11 筒体、转盘质量及转动惯量计算2 1.1筒体壁厚的计算2 1.2筒体体积计算3 1.3筒体质量计算4 1.4筒体转动惯量计算5 1.5轴盘及转动惯量的计算52 电机的选择7 2.1类型7 2.2功率计算7 2.2.1启动转鼓等转动件所需功N1 7 2.2.2 克服转鼓、物料与空气摩擦所需的功率N27 2.3 选定82.4 工作原理8 2.4.1 工作条件.8 2.4.2 负载特性8 2.4.3 离心式分离机82.4.4 外形及安装尺寸Y90S-6.83 带轮的设计11 3.1 计算功率Pa113.2 选择带轮型号11 3.3 确定带轮的基准直径D1、D2113.4 验算带轮V113.5 确定中心距a和带的基准直径Ld.123.6验算小带轮上的包角.123.7 确定带的根数Z123.8 计算轴压力Q133.9 带轮材质133.10 小带轮质量计算133.10.2 部分质量计算143.10.3 部分质量计算143.10.4 总质量m.14 3.11 大带轮质量计算153.11.1 部分质量计算153.11.2 部分质量计算153.11.3 总质量m154轴的设计和校核16 4.1 轴的设计计算164.1.1 按弯扭合成强度计算轴径公式16 4.1.2 按扭转刚度计算轴径的公式1641.3 取轴径164.2 轴的结构设计174.2.1 轴的强度计算.175 总质心的校核19 5.1 轴总质心的校核.195.1.1 轴质量计算195.1.2 轴质心校核.206 轴承的选择216.1 轴承的选择.设计及寿命校核.216.3 确定轴承寿命216.2 当量动载荷217 铆钉的计算22 7.1取半圆头铆钉227.2.2 按扭转强度计算227.2.1 按铆钉剪切强度计算227.2 确定铆钉的个数228 成型机的生产流程及电气控制238.1 生产流程238.2 电气控制原理249 总结2610 参考文献2711 致谢2812 附录29引言 片材离心成型机是使聚氨酯能够被应用的重要的生产设备,目前世界各国对聚氨酯类产品的需求之旺盛,聚氨酯产品种类之多已经远远超出之前人们的预估,我国作为发展中国家在聚氨酯的成型技术方面还有些许不足,本篇论文所研究的片材离心成型机就是为了改善国内聚氨酯成型技术,通过对聚氨酯材料特性的了解,以及国内对聚氨酯需求的种类要求,加以研究调查,整理出大量材料,针对需求进行逆向研究。能够进行研究的最重要一方面是对聚
温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
提示  人人文库网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。
关于本文
本文标题:机械毕业设计-400×1500片材离心成型机设计(含CAD图纸全套)
链接地址:https://www.renrendoc.com/p-50653721.html

官方联系方式

2:不支持迅雷下载,请使用浏览器下载   
3:不支持QQ浏览器下载,请用其他浏览器   
4:下载后的文档和图纸-无水印   
5:文档经过压缩,下载后原文更清晰   
关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

网站客服QQ:2881952447     

copyright@ 2020-2025  renrendoc.com 人人文库版权所有   联系电话:400-852-1180

备案号:蜀ICP备2022000484号-2       经营许可证: 川B2-20220663       公网安备川公网安备: 51019002004831号

本站为文档C2C交易模式,即用户上传的文档直接被用户下载,本站只是中间服务平台,本站所有文档下载所得的收益归上传人(含作者)所有。人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。若文档所含内容侵犯了您的版权或隐私,请立即通知人人文库网,我们立即给予删除!