链斗输送机装配检验记录 Inspection Report on Complete Machine of Bucket chain conveyor.doc

链斗输送机装配检验记录chain bucket conveyor Check Record 合 同 号Contract number机型TypeUser名称name检验项目Testing items技术要求Techinal requirements检验结果Testing results(允许打“”或“”)(Allow to sign “”or“”)制作者及交验日期Producers and the date of Producing for examination头部HEADPART1、头轴、机壳复验First axis、machine shell check again符合装配图要求Meet the requirements of assembly picture符合Eligible毛国柱Mao guozhu2010-4-52、头轮齿数、节距Firs twheel drawingteeth number、knot distance、符合装配图要求 Meet the requirements of assembly pictureZ= 5.5 t=2503、大链轮齿数、节距Large sprocke drawi teeth number、knot distance符合装配图要求Meet the requirements of assembly pictureDrawing No. Z= 52 t=38.14、产品标牌Product label内容正确,安装牢固Content correc，Firmly installed符合Eligible5、装配型式Assembly type符合生产表要求Meet the requirements of production table左( ) 右( )Left() right( ) 6、头轮旋转方向First wheel rotation direction符合装配图要求,标识正确Meet the requirements of assembly picture，the mark is right符合Eligible7、头轮中央平面对壳体对称平面对称度The symmetry between the surface of the first wheel center and the symmetric surface of the shell body 1.5mm1.5mm1.5mm8、头轮转动灵活性Flexibility of first wheel rotation手搬转灵活、无卡阻hands switch is flexible、without block符合Eligible9、头轮中心高Height of first wheel尺寸符合装配图要求且两轴承位等高Size meets requirements of the assembly picture and the height of the two axis is the same符合Eligible10、头轮及头轴定位可靠性reliability of the first wheeland first axiss posistion定位方式符合装配图要求,定位可靠Type of setting position meets requirements of assembly picture and it is reliable符合Eligible11、头部侧压板与其相配面装配间隙Space between head side plate and match surface device0.5mm0.5mm12、轮、轴、键配合精度、轴密封型式The cooperation accuracy among wheel、axis、key and type of the asis seal轮、轴、键配合符合装配图要求;轴密封型式符合装配图要求The cooperation among wheel、axis and key meets requirements of assembly picture;type of the asis seal meets requirements of assembly picture符合Eligible13、各联接部位联接质量及密封、润滑the quality among all parts and seal、lubrication联接部位联接紧密;密封垫符合产品图样;气密型联接部位不允许存在间隙.轴承腔内充满润滑脂The connection parts connect well; type of the asis seal meets requirements of product design;no space in air seal connected part;the cavity of axis is full of grease符合Eligible14、外观appearance外观无明显缺陷,贴合面贴合前上底漆;焊接牢固且施焊处彻底清除焊渣;壳体内应无杂物、铁屑Appearance no obvious defects;put the primer on the joint surface before jointed;welding firmly and clean welding slag in welding place;shell should be no junk and iron slag符合Eligible尾部TAILPART1、尾部调节装置装配Tail adjustment device assembly 调节可靠、有效、全程调节灵活、方便Reliable、effctive、fexible、convenient符合Eligible毛国柱Mao guozhu2010-4-72、尾部调节行程The trip of tail adjutment符合装配图要求Meet the requirements of assembly picture符合Eligible3、滑动板与尾部侧板间隙space between the sliding board and tail sideboard0.5mm0.5mm4、尾轮tail wheel符合装配图要求Meet the requirements of assembly picture符合Eligible5、尾轮中央平面对壳体对称平面对称the symmetry between center surface of tail wheel and shell body symmetric surface1.5mm1.5mm6、尾轮转动灵活性Flexibility of tail wheel rotation手搬转、灵活、卡阻hands switch is flexible、without block符合Eligible7、尾轮中心高Height of the center of tail wheel尺寸符合装配图要求且两轴承位等高Meet the size requirements assembly picture and the height of the bearing is the same 符合Eligible8、尾轮及尾轴定位可靠性reliability of tail wheel and the position of tail axis定位符合装配图要求、可靠Setting position meets requirements of assembly picture and reliable符合Eligible9、各联接部位联接质量、密封、润滑the quality among all parts and seal、lubrication联接部位联接紧密;密封垫符合产品图样;气密型联接部位不允许存在间隙.轴承内腔充满润滑脂尾部丝杆涂黄油润滑The parts connect well; type of the asis seal meets requirements of product design;no space in air seal connected part;the cavity of axis is full of grease符合Eligible10、外观Appearance外观无明显缺陷、贴合面贴合前上底漆;焊接牢固且施焊处彻底清除焊渣;壳体内应无杂物、铁屑Appearance no obvious defects;put the primer on the joint surface before jointed;welding firmly and clean welding slag in welding place;shell should be no junk and iron slag符合Eligible驱动装置DRIVINGARRANGEMENT1、电机型号、主要参数、标识Motor models、Main Parameters、logo产品标识内容符合生产表要求,有进货检验合格证标识The contents of the product mark meet the requirements of production table,have the purchase qualified check mark型号:Model Y112M-4/Y132S-4功率: power 4kw/54kw防护等级Protection levels IP55绝缘等级: Insulation levels :F毛国柱Mao guozhu2010-4-72、减速器型呈、主要参数、标识Gearbox models 、Main Parameters、 logo产品标识内容符合生产表要求,有进货检验合格证标识The contents of the product mark meet the requirements of production table,have the purchase qualified check mark型号:ZSY160-71-modelXWD4.0-7-74/XWD5.5-8-873、小链轮、齿数、节距small sprocket teeth number、knot distance符合装配图要求Meet the requirements of assembly pictureZ=15 t=38.14、轮、轴、键配合精度The cooperation accuracy among wheel、axis、key符合装配图要求Meet the requirements of assembly picture符合Eligible5、驱动装置架钻孔the drilled hole of driving device frame符合产品图样Meet product design符合Eligible6、试车后电器验收After trying the car, check and accept是否按要求拆卸Whether follow the required demoli