配置VLAN间通过VLANIF接口通信博客.docx

配置VLAN间通过VLANIF接口通信任务：配置vlan间通过vlanif接口进行通信，要求LSW2上vlan10里的pc1与vlan20里的pc2之间能相互通信在eNSP模拟器上交换机没有Eth接口，为完成此配置实验，需准备如下的数据：1.在LSW1上配置接口GE0/0/1加入VLAN10 和VLAN20。2.在LSW1上配置VLANIF10 的IP 地址为192.168.2.1/24。3.在LSW1上配置VLANIF20 的IP 地址为192.168.3.1/24。4.在LSW2上配置接口GE0/0/1加入VLAN10 和VLAN20。6.在LSW2上配置接口GE0/0/2加入VLAN10。7.在LSW2上配置接口GE0/0/3加入VLAN20。设备之间连接如下图所示： 操作如下：一、配置交换机LSW1system-view Enter system view, return user view with Ctrl+Z.Huaweiundo info-center enableInfo: Information center is disabled.Huaweivlan batch 10 20Info: This operation may take a few seconds. Please wait for a moment.done.Huaweiinterface giga 0/0/1Huawei-GigabitEthernet0/0/1port link-type trunkHuawei-GigabitEthernet0/0/1port trunk allow-pass vlan 10 20Huawei-GigabitEthernet0/0/1quitHuaweiinterface vlanif 10Huawei-Vlanif10ip address 192.168.2.1 24Huawei-Vlanif10quitHuaweiinterface vlanif 20Huawei-Vlanif20ip address 192.168.3.1 24Huawei-Vlanif20quitHuawei二、配置交换机LSW2system-viewEnter system view, return user view with Ctrl+Z.Huaweiundo info-center enableInfo: Information center is disabled.Huaweivlan batch 10 20Info: This operation may take a few seconds. Please wait for a moment.done.Huaweiinterface giga 0/0/1Huawei-GigabitEthernet0/0/1port link-type trunkHuawei-GigabitEthernet0/0/1port trunk allow-pass vlan 10 20Huawei-GigabitEthernet0/0/1quitHuaweiinterface eth 0/0/1 Error: Wrong parameter found at position.Huaweiinterface ethernet 0/0/1 Error: Wrong parameter found at position.上面的命令出错了，在模拟器上没有ethernet接口Huaweiinterface giga 0/0/2Huawei-GigabitEthernet0/0/2port link-type accessHuawei-GigabitEthernet0/0/2port default vlan 10Huawei-GigabitEthernet0/0/2quitHuaweiinterface giga 0/0/3Huawei-GigabitEthernet0/0/3port link-type accessHuawei-GigabitEthernet0/0/3port default vlan 20Huawei-GigabitEthernet0/0/3quitHuawei User interface con0 is available三、配置两台PC电脑 设置PC1的IP为 192.168.2.2 24 192.168.2.1 设置PC2的IP为 192.168.3.2 24 192.168.3.1 四、检查结果在PC1上能ping通PC2在PC2上能ping通PC1配置前与配置后的对比Welcome to use PC Simulator!PCping 192.168.2.2Ping 192.168.2.2: 32 data bytes, Press Ctrl_C to breakFrom 192.168.3.2: Destination host unreachableFrom 192.168.3.2: Destination host unreachableFrom 192.168.3.2: Destination host unreachableFrom 192.168.3.2: Destination host unreachableFrom 192.168.3.2: Destination host unreachablePCping 192.168.2.2Ping 192.168.2.2: 32 data bytes, Press Ctrl_C to breakFrom 192.168.2.2: bytes=32 seq=1 ttl=127 time=62 msFrom 192.168.2.2: bytes=32 seq=2 ttl=127 time=47 msFrom 192.168.2.2: bytes=32 seq=3 ttl=127 time=63 msFrom 192.168.2.2: bytes=32 seq=4 ttl=127 time=47 msFrom 192.168.2.2: bytes=32 seq=5 ttl=127 time=47 ms- 192.168.2.2 ping