文档包括:
说明书一份。38页,18800字。
论文申报表一份。
外文翻译一份。
图纸共19张,如下所示
A0-底面预弯模.dwg
A0-落料冲孔模.dwg
A0-零件图-7张.dwg
A0-零件图-9张.dwg
A1-压弯成型模.dwg
摘 要
本文主要以后悬置左支架为研究对象,根据产品的特点以及其冲压模具设计的要求,制定了冲压加工工艺并进行了模具结构设计。
通过对后悬置左支架结构特点的分析,制定了其冲压加工工艺。依据工艺分析确定需要三套冲压模具共同完成后悬置左支架的成形,分别是落料冲孔复合模具、第一次弯曲成型模具以及第二次弯曲成型模具。按照加工工艺,分别进行了毛胚尺寸的计算和冲裁模、弯曲工艺的计算,最终完成本次设计。
本文在模具设计中的设计方法可以有效地运用到其它冲模设计过程之中,可以大大降低设计和生产成本从而指导生产,为以后的冲压产品的生产找到了很好方法和手段。
关键词:模具设计 落料冲孔 Z型弯曲模 压弯成型模
ABSTRACT
In this paper, the rear suspension left bracket is studied, and according to the characteristics of the left bracket and requirements of die design, the stamping process and die structure is given.
Through the analysis on the structure characteristics of the rear suspension left bracket, the stamping process is designed. Based on the process analysis the paper identifies three sets of stamping die together to form rear suspension left bracket, namely composite blanking punching mold, the first bending mold and the second bending mold. Based on the stamping forming process the blank size and bending force is calculated.
The analysis and design method used in the paper can be put into the other die design process. It can significantly reduce production costs so as to guide the design and production of stamping products, and found ways and means for the production in the future.
Keyword: Mold Design Blanking punch Z-Bending Die Bending molding
目 录
第一章 绪 论 1
1.1冲压的概念、特点及应用 1
1.2冲压加工的基本工序及模具类型 2
1.2.1冲压的基本工序 2
1.2.2冲压模具的类型 2
1.3冲压技术和模具制造技术的现状及发展方向 3
1.4本文的研究目的及意义 5
第二章 后悬置左支架冲压成型工艺制定 7
2.1 冲压工艺的分析 7
2.2 冲压工序的确定 7
2.3 工艺方案的编制 8
第三章 冲压模具的设计与计算 10
3.1 落料冲孔模的设计与计算 10
3.1.1 板料排样设计与计算 10
3.1.2 冲裁力的计算 12
3.1.3 压力中心的计算 14
3.1.4 冲压设备的选用 15
3.1.5 凸凹模刃口尺寸计算 16
3.1.6 凸模、凹模、凸凹模的结构设计 18
3.2 弯曲模的设计与计算 22
3.2.1 Z型弯曲模的相关计算及模具设计 23
3.2.2 压弯成型模的相关计算及模具设计 26
第四章 模具结构设计的校核 31
4.1 凸模强度的校核 31
4.2 螺栓强度的校核 32
4.3 压力机闭合高度的校核 33
总 结 34
致 谢 35
参 考 文 献 36
题目来源、教师准备情况、主要培养学生哪些能力
1.本题目来源于指导教师的命题。
2.指导教师对此课题有深厚的理论基础及实际经验,在师生共同努力下定能顺利、按期完成该课题设计。
3.通过毕业设计强化对基本知识和基本技能的理解和掌握,培养自主收集资料和调查研究的能力,一定的方案比较、论证的能力,一定的理论分析与设计运算能力,进一步提高应用计算机绘图的能力以及编写编制能力。
4.培养学生对所学的机械原理、机械设计、机械工艺的实际应用情况。
题 目 内 容 及 要 求
题目:后悬置左支架的冲压工艺及模具设计
要求:
1.写出1~1.5万字的论文,绘制总装图及零件图。
2.论文内容包括:
(1)阐述国内外组合机床现状
(2)组合机床的总体设计
(3)机床夹具的设计
3.将一篇与本课题有关的英文资料,翻译成中文(约5000字)。




