大直径辊筒双头镗孔专机【12张图/14400字】【优秀机械毕业设计论文】

文档包括:
说明书一份,36页,14400字左右.

图纸共12张,如下所示
A0-承载装置工程图.dwg
A0-外形图.dwg
A0-自定心装置.dwg
A2-齿轮轴.dwg
A2-道夫辊筒.dwg
A3-固定导轨.dwg
A3-滑动导轨组合件.dwg
A3-旋转盘连杆组合件.dwg
A4-螺纹球柄.dwg
A4-扭杆弹簧转臂.dwg
A4-扭杆弹簧扭杆.dwg
A4-球面套筒.dwg

摘要
本论文是关于大直径辊筒双头镗孔专机承载装置和自定心装置的设计说明。首先，本文简要概述了课题的选题背景及发展现状，对双头镗孔专机的加工对象锡林辊筒及道夫辊筒进行了结构和加工工艺的分析。其次，根据承载装置和自定心装置的性能要求进行了方案的拟定并在方案对比分析的基础上确定出了相对合理的方案。承载装置对锡林辊筒与道夫辊筒的定位采用类似V形面的定位方式，驱动方式为减速电动机齿轮传动。自定心装置采用带双矩形导轨的可移动箱体实现三个旋转轴的同时进给，采用液压缸驱动六杆机构运动进而实现自定心装置的三个旋转轴同步转动。同时，对方案中用到的电动机、液压缸、扭杆弹簧进行了计算选择及连杆机构的运动确定性的验证。最后，校核了承载装置中驱动轴的强度及轴承的寿命，并在结论中总结了本设计的优点和创新点，对方案中存在的问题进行了分析并提出了改进方向。
关键词：承载装置 自定心装置 六杆机构

Abstract
This thesis is a piece of explanation of design that about the bearing and self-centering device of the specialized and two-headed boring machine to process the big diameter roller. 
Firstly, these papers briefly summarize the background and development present situation of the topic. It also analyze the structure and processing manufacturability of cylinder and doffer rollers which was processed by specialized and two-headed boring machine. 
Secondly, according to the performance requirement of the bearing and self-centering device to make the project block in, then on the basis of the project analysis make out a relatively reasonable project. The cylinder and doffer rollers are located by the V-shaped surface and the drive mode is reducer motors gear transmission. Self-centering device adopt the removable tank body with double rectangular guide rail to realize three axis remove in the meantime. It also adopts hydraulic cylinder driving mechanism drive linkage mechanism to realize the three axes rotate meanwhile. At the same time, makes a calculation and choice to the motor and hydraulic cylinder used in the project.
Finally, checks the strength of drive shaft and bearing life of bearing device, summarizes this designing project’s advantage and innovations, analyzes the problems in the project and put up with improving direction.
Key words: bearing device self-centering device six-connecting rod mechanism

目录
引言 1
1 课题介绍 2
1.1 课题名称 2
1.2 课题概述 2
1.3 课题背景及发展现状 2
2 零件的结构和加工工艺分析 4
2.1 辊筒的加工工艺要求 5
2.2 辊筒的加工工艺流程 5
2.3 零件的工艺分析 5
3 方案拟定 6
3.1 承载装置及自定心装置的设计要求 6
3.1.1 承载装置的设计要求 6
3.1.2 自定心装置的设计要求 7
3.2 课题可行性分析 7
3.3 方案的设计与对比分析 8
3.3.1 承载装置方案设计 8
3.3.2 承载装置方案的对比分析 12
3.3.3 自定心装置方案设计 13
3.3.4 自定心装置方案的对比分析 17
3.4 方案的选择确定 18
4 理论计算及关键零部件的校核 18
4.1 理论计算 18
4.1.1 电动机的选择 18
4.1.2 液压缸的选择 19
4.1.3 连杆机构的计算 22
4.1.4 自定心装置中扭杆弹簧的计算 23
4.2 关键零部件的校核 25
4.2.1 承载装置驱动轴的校核 25
4.2.2 键联接的选择与校核 28
4.2.3 轴承的校核 28
结论 30
参考文献 31
致谢 32
附录 33