文档包括:
说明书一份,38页,13500字左右。
任务书一份。
图纸共8张,如下所示
A0-后盖.dwg
A0-多轴箱装配图.dwg
A0-机床尺寸联系图.dwg
A0-箱体补充加工图.dwg
A2-加工示意图.dwg
A3-加工零件零件.dwg
A3-轴承主轴.dwg
A3-零件工序图.dwg
目 录
摘 要 I
Abstract II
第1章 绪论 1
1.1 组合机床综述 1
1.2 组合机床总体设计 2
1.2.1 被加工零件的特点 3
1.2.2 工艺路线的确立 3
1.2.3 机床配置型式的选择 4
第2章 组合机床的结构设计与计算 5
2.1 切削扭矩及切削功率的计算 5
2.2 组合机床总体设计 6
2.2.1 被加工零件工序图 6
2.2.2 加工示意图 8
2.2.3 机床联系尺寸总图 13
2.2.4 机床生产率计算卡 15
2.3 确定主轴箱轮廓尺寸 17
2.4 通用部件的选择 18
第3章 组合机床主轴箱设计 20
3.1 绘制主轴箱设计原始依据图 20
3.2 主轴、齿轮的确定及动力计算 21
3.3 主轴箱传动系统的设计与计算 22
3.3.1 驱动轴、主轴的坐标计算 22
3.3.2 拟订主轴箱传动路线 22
3.3.3 确定传动轴位置和齿轮齿数 22
3.4 多轴箱坐标计算、绘制坐标检查图 24
3.4.1 选择加工基准坐标系XOY,计算主轴、驱动轴坐标 24
3.4.2 计算传动轴的坐标 24
3.4.3 绘制坐标检查图 24
3.5 齿轮强度校核 24
3.5.1 校核齿根弯曲疲劳强度 25
3.5.2 校核接触疲劳强度 26
3.6 传动轴直径的确定和轴的强度校核 27
3.6.1 轴的直径的确定 27
3.6.2 轴的强度校核 27
3.7 主轴箱体及其附件的选择设计 31
3.7.1 主轴箱的选择设计 32
3.7.2 主轴箱上的附件设计 32
结 论 33
致 谢 34
参考文献 35
CONTENTS
Abstract II
The 1 chapter of introduction 1
1.1 Combination machine Reviews 1
1.2 Modular machine tool design 2
1.2.1 The characteristics of processed parts 3
1.2.2 Process route is established 3
1.2.3 Machine configuration type selection 4
The 2 chapter of structure design and calculation of combined machine tool 5
2.1 Cutting torque and cutting power calculation 5
2.2 Modular machine tool design 6
2.2.1 Processed the components working procedure chart 6
2.2.2 The processing schematic drawing 8
2.2.3 The engine bedrelation dimensional layout 13
2.2.4 Machine productivity calculation card 15
2.3 Determining the spindle box outline size 17
2.4 The choice of generic components 18
The 3 chapter combined machine tool headstock design 20
3.1 Draw spindle box based on the original design plans 20
3.2 Main shaft, gear determination and power calculation 21
3.3 Spindle box drive system design and calculation 22
3.3.1 Drive shaft, spindle coordinate calculation 22
3.3.2 Elaboration of spindle box transmission line 22
3.3.3 To determine the location and teeth of gear transmission shaft 22
3.4 Multiple spindle coordinate calculation, drawing coordinate test chart 24
3.4.1 Selection of machining datum coordinate system XOY, main shaft,
drive shaft coordinates calculation 24
3.4.2 Calculation of transmission axis of coordinates 24
3.4.3 The drawing coordinate test chart 24
3.5 Gear strength 24
3.5.1 Check the tooth root bending fatigue strength 25
3.5.2 Check the contact fatigue strength 26
3.6 Drive shaft diameter is determined and the axis of strength checking 27
3.6.1 Shaft diameter determination 27
3.6.2 The axis of strength checking 27
3.7 Spindle box and accessories selection design 31
3.7.1 The selection and design of spindle box 32
3.7.2 Spindle box attachment material design 32
Conclusion 33
Thanks 34
Reference 35
摘 要
本次设计的题目是发动机支架立式单面组合钻床设计,是在发动机支架上加工4个深6mm,尺寸要求 17的孔。
本次设计分为总体设计和主轴箱设计两个部分。首先,对机床进行总体结构的设计,需要确定切削用量、计算切削力、切削扭矩、切削功率及刀具耐用度,然后以此确定主轴、外伸尺寸等,绘制“三图一卡”,即被加工零件工序图、加工示意图、机床尺寸联系总图,以及生产率计算卡。其次,对主轴箱进行设计,绘制设计原始依据图,确定主轴箱及各个通用部件的选用,计算各齿轮的传动比和主轴的坐标位置。最后,根据分析的结果,对齿轮和轴的强度和刚度进行校核。
本专用机床能满足加工要求,保证加工精度,机床运转平稳,工作可靠,结构简单,装卸方便,便于维修、调整、操作,减轻了工人的劳动强度,提高了劳动生产率。
关键词:组合机床;钻孔;主轴箱;传动设计
Abstract
The design topic is Engine bracket of vertical single combination drilling machine design. Aimed at the engine support processing 4 meet the size requirements of the 17 and 6mm deep hole.
The design is divided into two parts overall design and the headstock design. Firstly, the overall structure of the machine tools design, need to determine the cutting parameters, calculation of cutting force, cutting torque, cutting power and tool life, and thus determine the main shaft, extended size, etc..Rendering the "three plans for a card", that is, process map parts to be processed, processing diagram, machine sizes contact General Plan, and the productivity calculation card. Secondly, the design of the spindle box, drawing the original design basis, for the identification of various common spindle box and the selection of components, to calculate the transmission gear ratios and the principal axis coordinates. Finally, the results of the analysis, the gear and shaft to check the strength and stiffness.
This special machine can meet the processing requirements to ensure the machining accuracy, tool smooth operation, reliable, simple, easy handling, easy maintenance and adjustment. Operation simple, reducing labor intensity and improve labor productivity.
Key words:special purpose machine; drilling; spindle box; transmission design
一、设计题目:发动机支架立式单面组合钻床设计
二、设计的主要内容:
(1)设计参数:材料是HT200,硬度是HB160~210。
(2)设计图纸:主轴箱装配图1张,箱体、后盖、输出主轴、工件零件图各1张,机床尺寸联系图、加工示意图、零件工序图各1张。
(3)说明书主要内容及字数要求:
说明书主要内容:1)中英文摘要;2)组合机床总体结构设计与计算;3)组合机床主轴箱设计。
字数:1.5万字以上
三、设计目标:根据发动机支架设计要求,查阅相关文献资料,综合运用所学知识,完成相应机构设计。主要包括:总体设计方案的确定;三图一卡的设计;主轴箱的设计等。按照工程设计规范要求,绘制工程图,并编写设计说明书。







